• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.331-336
• /
• 2021

The Non-dispersive Infrared (NDIR) gas sensor has high selectivity, measurement reliability, and long lifespan. Thus, even though the NDIR gas sensor is expensive, it is still widely used for carbon dioxide (CO₂) detection. In this study, to reduce the cost of the NDIR CO₂ gas sensor, we proposed the new optical waveguide structure design based on ready-made gas pipes that can improve the sensitivity by increasing the initial light intensity. The new optical waveguide design is a structure in which a part of the optical waveguide filter is inclined to increase the transmittance of the filter, and a parabolic mirror is installed at the rear end of the filter to focus the infrared rays passing through the filter to the detector. In order to examine the output characteristics of the new optical waveguide structure design, optical simulation was performed for two types of IR-source. As a result, the new optical waveguide structure can improve the sensitivity of the NDIR CO₂ gas sensor by making the infrared rays perpendicular to the filter, increasing the filter transmittance.

• Korean Journal of Materials Research
• /
• v.20 no.8
• /
• pp.408-411
• /
• 2010

Indium doped $SnO_2$ thick films for gas sensors were fabricated by a screen printing method on alumina substrates. The effects of indium concentration on the structural and morphological properties of the $SnO_2$ were investigated by X-ray diffraction and Scanning Electron Microscope. The structural properties of the $SnO_2$:In by X-ray diffraction showed a (110) dominant $SnO_2$ peak. The size of $SnO_2$ particles ranged from 0.05 to $0.1\;{\mu}m$, and $SnO_2$ particles were found to contain many pores, according to the SEM analysis. The thickness of the indium-doped $SnO_2$ thick films for gas sensors was about $20\;{\mu}m$, as confirmed by cross sectional SEM image. Sensitivity of the $SnO_2$:In gas sensor to 2000 ppm of $CO_2$ gas and 50 ppm of H2S gas was investigated for various indium concentrations. The highest sensitivity to $CO_2$ gas and H2S gas of the indium-doped $SnO_2$ thick films was observed at the 8 wt% and 4 wt% indium concentration, respectively. The good sensing performances of indium-doped $SnO_2$ gas sensors to $CO_2$ gas were attributed to the increase of oxygen vacancies and surface area in the $SnO_2$:In. The $SnO_2$:In gas sensors showed good selectivity to $CO_2$ gas.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.1
• /
• pp.83-86
• /
• 2004

A high temperature tolerant microelectronic-based carbon monioxde(CO) gas sensor has been developed. The gas sensing performance has been studied over a wide temperature range$(100-300^\circ{C)}$. The gas sensitivity of the sensor is high, its initial sensing behavior is very fast, and the sensor is reproducible. Pt-SiC and $Pt-SnO_2-SiC$ diodes are fabricated using standard semiconductor processes and their CO gas-sensing behaviors are analyzed as a function of CO gas concentration and temperature by I-V and $\Delta{I-t}$ methods under steady-state and transient conditions. The sensitivity of the device with $Pt-SnO_2$ catalytic gate is higher than that of the Pt gate. The experimental results indicate that $SnO_2$ layer improves the catalytic reaction of the Pt layer.

• Journal of Sensor Science and Technology
• /
• v.19 no.5
• /
• pp.385-390
• /
• 2010

CO sensing thick film gas sensors using $Co_3O_4$ powders prepared by hydrothermal reaction method, were fabricated, and their structural, electrical and CO gas sensing properties were investigated. The specific surface area of the $Co_3O_4$ powders obtained from BET analysis was about 79.0 $m^2/g$. XRD and SEM results show that the thick films heat-treated at $500^{\circ}C$ for 30 min after screen printing had the preferred orientation of (311) direction and the crystalline size was calculated to 221 $\AA$. The maximum activation energy obtained from the temperature-resistance characteristics was 3.11 eV in the temperature range of $290^{\circ}C$ to $310^{\circ}C$. The sensitivity to 1,000 ppm CO was about 150 %. The specific surface area, crystalline size, and maximum activation energy were increased significantly and the sensitivity for CO gas was improved largely.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.453-457
• /
• 1998

In order to improve CO gas sensitivity, $TiO_2$added $SnO_2$ composite ceramics were prepared. Using XRD and SEM, the phases and micro structures of these ceramics were investigated. The resistances as a function of gas atmosphere were measured by High Voltage Measure/Source Unit. The maximum 100 ppm CO gas sensitivities of $SnO_2-TiO_2$composites were 2.5 times larger than that of pure $SnO_2$ composite and showed the obvious temperature dependence of sensitivities in 500, 100 ppm CO gas atmospheres.

• Journal of Sensor Science and Technology
• /
• v.17 no.4
• /
• pp.303-307
• /
• 2008

$NiO,\;Cu_2O,\;Mn_2O_3$ and $Cr_2O_3$ as p-type semiconductors were added in CoO with 15 wt.% ethylene glycol binder and measured the butane gas sensing characteristics. The highest sensitivity is obtained for the NiO-CoO sensors. CoO-20 at.% NiO sensor with 15 wt.% ethylene glycol binder sintered at $1100^{\circ}C$ for 24 h exhibits high sensitivity of 90 % to 5000 ppm butane gas at the sensor temperature of $250^{\circ}C$, compared to low sensitivities at the low operating temperature for commercial sensors. Response and recovery times are, respectively, within few seconds and 1min in the static flow system, indicating rapid adsorption and desorption of butane gas on sensor surface even at this low temperature.

• Journal of Sensor Science and Technology
• /
• v.20 no.6
• /
• pp.406-411
• /
• 2011

$Co_3O_4$ thick film gas sensor using the powder prepared by hydrothermal reaction method(HRM) was fabricated. For comparison study, we also prepared the sensor using commercial $Co_3O_4$ powder under the same fabrication conditions. Sensitivity, time response, and selectivity of them to variable gases such as iso-$C_4H_{10}$, CO, $NH_3$, and $CH_4$ were investigated. The sensor from the powder prepared by HRM showed higher sensitivity to every gas than those from commercial powder. For iso-$C_4H_{10}$ gas, the sensitivities of both sensor to 100 ppm are 160 % and 40 %, respectively. Time response and selectivity of the sensor using the powder prepared by HRM were better than those of the sensor using commercial powder.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.39-40
• /
• 1993

• Journal of the Korean Ceramic Society
• /
• v.47 no.1
• /
• pp.92-96
• /
• 2010

Based on the differential electrode equilibria approach, potentiometric YSZ sensors with semiconducting oxide electrodes for CO detection are developed. To improve the selectivity, sensitivity and response-time of the sensor, our strategy includes (a) selection of an oxide with a semiconducting response to CO, (b) addition of other semiconducting materials, (c) addition of a catalyst (Pd), (d) utilization of combined p- and n-type electrodes in one sensor configuration, and (e) optimization of operating temperatures. Excellent sensing performance is obtained by a novel device structure incorporating $La_2CuO_4$ electrodes on one side and $TiO_2$-based electrodes on opposite substrate faces with Pt contacts. The resulting response produces additive effects for the individual $La_2CuO_4$ and $TiO_2$-based electrodes voltages, thereby realizing an even higher CO sensitivity. The device also is highly selective to CO versus NO with minor sensitivity for NO concentration, compared to a notably large CO sensitivity.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.9
• /
• pp.1621-1625
• /
• 2010

Recently, due to increase in the usage of toxic gas and inflammability gas, the ability to monitor and precisely measurement of these gases is crucial in preventing the occurrence of various accidents. CuO doped and undoped $WO_3$ thick films gas sensors were prepared using screen-printing method on alumina substrates. A structural properties of $WO_3$:CuO thick films had monoclinic phase and triclinic phase of $WO_3$ together. Sensitivity of $WO_3$:CuO sensor at 2000 ppm of $CO_2$ gas and 50 ppm of $H_2S$ gas was investigated. 4 wt% Cu doped $WO_3$ thick films had the highest sensitivity of $CO_2$ gas and $H_2S$ gas.