• Journal of Sensor Science and Technology
• /
• v.32 no.4
• /
• pp.238-245
• /
• 2023

0.75(Bi_1/2Na_1/2)TiO₃-0.25SrTiO₃ (BNT-25ST) ceramics with high densities were successfully prepared at a sintering temperature of 1,000℃ by adding a mixture of 1 mol% CuO and 0.5 mol% Na₂CO₃ or 0.5 mol% CuO and 0.25 mol% Na₂CO₃. Double polarization-electric field (P-E) hysteresis curves and sprout-shaped bipolar strain-electric field (S-E) hysteresis curves with small negative strains were observed in the pristine and CuO-added BNT-25ST ceramics whereas the Na₂CO₃-added sample showed similar P-E and S-E curves to a typical ferroelectric. The pristine BNT-25ST ceramics showed an extremely large strain and a large-signal piezoelectric strain constant (d₃₃^*): 0.287 % at 80 kV/cm and 850 pm/V at 20 kV/cm. Similar values, 0.248 % at 80 kV/cm and 655 pm/V at 20 kV/cm, were obtained in the CuO-added sample. However, the pristine and CuO-added samples showed large hysteresis in unipolar S-E curves at an electric field of less than 20 kV/cm. The Na₂CO₃-added sample showed smaller values of the strain and d₃₃^* but displayed a linear change and small hysteresis in the unipolar S-E curve. The co-added sample with CuO and Na₂CO₃ displayed intermediate P-E and S-E hysteresis curves.

• Clean Technology
• /
• v.28 no.1
• /
• pp.1-8
• /
• 2022

To confirm the applicability of the water gas shift reaction for the production of high purity hydrogen for petroleum cokes, an unutilized low grade resource, Cu/ZnO/MgO/Al₂O₃ (CZMA), catalyst was prepared using the co-precipitation method. The prepared catalyst was analyzed using BET and H₂-TPR. Catalyst reactivity tests were compared and analyzed in two cases: a single LTS reaction from syngas containing a high concentration of CO, and an LTS reaction immediately after the syngas passed through a HTS reaction without condensation of steam. Reaction characteristics in accordance with steam/CO ratio, flow rate, and temperature were confirmed under both conditions. When the converted low concentration of CO and steam were immediately injected into the LTS, the CO conversion was rather low in most conditions despite the presence of large amounts of steam. In addition, because the influence of the steam/CO ratio, temperature, and flow rate was significant, additional analysis was required to determine the optimal operating conditions. Meanwhile, carbon deposition or activity degradation of the catalyst did not appear under high CO concentration, and high CO conversion was exhibited in most cases. In conclusion, it was confirmed that when the Cu/ZnO/MgO/Al₂O₃ catalyst and the appropriate operating conditions were applied to the syngas composition containing a high concentration of CO, the high concentration of CO could be converted in sufficient amounts into CO₂ by applying a single LTS reaction.

• Clean Technology
• /
• v.21 no.1
• /
• pp.39-44
• /
• 2015

This study investigated the effects of six metal oxide nanoparticles (NPs: CuO, NiO, TiO₂, Fe₂O₃, Co₃O₄, ZnO) on seed germination and germination index (G.I) for five types of seeds: Brassica napus L., Malva verticillata L., Brassica olercea L., Brassica campestris L., Daucus carota L. NPs of CuO, ZnO, NiO show significant toxicity impacts on seed activities [CuO (6-27 mg/L), ZnO (16-86 mg/L), NiO (48-112 mg/L)], while no significant effects were observed at > 1000 mg/L of TiO₂, Fe₂O₃, Co₃O₄. Tested five types of seed showed different sensitivities on seed germination and root activity, especially on NPs of CuO, ZnO, NiO. Malva verticillata L. seed was highly sensitive to toxic metal oxide NPs and showed following EC₅₀s : CuO 5.5 mg/L, ZnO 16.4 mg/L, NiO 53.4 mg/L. Mostly following order of toxicity was observed, CuO > ZnO > NiO > Fe₂O₃ ≈ Co₃O₄ ≈ TiO₂, where slightly different toxicity order was observed for carrot, showing CuO > NiO ≈ ZnO > Fe₂O₃ ≈ Co₃O₄ ≈ TiO₂.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.9
• /
• pp.1695-1698
• /
• 2008

• Environmental and Resource Economics Review
• /
• v.30 no.4
• /
• pp.607-625
• /
• 2021

The objective of this study is to estimate the relationship between CO₂ emissions and both nuclear power and renewable energy generation, and compare the cost efficiencies of nuclear power and renewable energy generation in reducing CO₂ emissions in Korea. The results show that nuclear power and renewable energy generation should be increased by 1.344% and 7.874% to reduce CO₂ emissions by 1%, respectively. Using the estimated coefficients and the levelized costs of electricity by source including the external costs, if the current amount of electricity generation is one megawatt-hour, the range of generation cost of nuclear power generation to reduce 1% CO₂ emissions is $0.72~$1.49 depending on the level of external costs. In the case of renewable energy generation, the generation cost to reduce 1% CO₂ emissions is $6.49. That is, to mitigate 1% of CO₂ emissions at the total electricity generation of 353 million MWh in 2020 in Korea, the total generation costs range for nuclear power is $254 million~$526 million for the nuclear power, and the cost for renewable energy is $2.289 billion for renewable energy. Hence, we can conclude that, in Korea, nuclear power generation is more cost-efficient than renewable energy generation in mitigating CO₂ emissions, even with the external costs of nuclear power generation.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.6
• /
• pp.115-131
• /
• 2022

Carbon dioxide (CO₂) emissions from the transportation sector in South Korea accounts for 16.5% of all CO₂ emissions, and road transportation accounts for 96.5% of this sector's emissions in South Korea. Hence, constant research is being carried out on methods to reduce CO₂ emissions from this sector. With the emerging use of smart crossings, attempts to monitor individual vehicles are increasing. Moreover, the potential commercial deployment of autonomous vehicles increases the possibility of obtaining individual vehicle data. As such, CO₂ emission research was conducted at five signalized intersections in the Gangnam District, Seoul, using data such as vehicle type, speed, acceleration, etc., obtained from image detectors located at each intersection. The collected data were then applied to the MOtor Vehicle Emission Simulator (MOVES)-Matrix model-which was developed to obtain second-by-second vehicle activity data and analyze daily CO₂ emissions from the studied intersections. After analyzing two large and three small intersections, the results indicated that 3.1 metric tons of CO₂ were emitted per day at each intersection. This study reveals a new possibility of analyzing CO₂ emissions using actual individual vehicle data using an improved analysis model. This study also emphasizes the importance of more accurate CO₂ emission analyses.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.26 no.4
• /
• pp.327-342
• /
• 2021

The global coastal region is considered as a sink for atmospheric CO₂. Since most of the studies in the East Sea focused on the Ulleung Basin, the importance of coastal region for carbon cycle has been overlooked. In this study, we compared the biological pump and CO₂ absorption between the Ulleung Basin and coastal region by surface measurements of biological O₂ supersaturation (𝚫O₂/Ar) and partial pressure of CO₂ (fCO₂). Cold and less saline waters in the coastal regions were in contrast with a warm and saline water in the Ulleung Basin. The coastal waters near Samcheok and Pohang showed higher fluorescence, 𝚫O₂/Ar, and lower fCO₂ than those in the Ulleung Basin, indicating higher primary production and CO₂ absorption in the areas. The average net community production estimated by 𝚫O₂/Ar were 19 ± 6 and 60 ± 9 mmol O₂ m^-2d^-1 in the Samcheok and Pohang, respectively, 2-7 times higher than that of 8 ± 4 mmol O₂ m^-2d^-1 in the Ulleung Basin. Similarly, the average CO₂ flux between the seawater and atmosphere were -17.1 ± 8.9 and -25.8 ± 13.2 mmol C m^-2d^-1 in the Samcheok and Pohang, respectively, 4-5 times higher than that of -4.7 ± 2.5 mmol C m^-2d^-1 in the Ulleung Basin. In the Samcheok and Pohang, degrees of N₂ saturation were lower by 3% than that the ambient waters, suggesting the possibility of nitrogen fixation by primary producers.

• Economic and Environmental Geology
• /
• v.53 no.1
• /
• pp.33-43
• /
• 2020

CO₂ geological storage is currently considered as the most stable and effective technology for greenhouse gas reduction. The saline formations for CO₂ geological storage are generally located at a depth of more than 800 m where CO₂ can be stored in a supercritical state, and an extensive impermeable cap rock that prevents CO₂ leakage to the surface should be distributed above the saline formations. Trough analysis of seismic and well data, we identified the basalt flow structure for potential CO₂ storage where saline formation is overlain by basalt cap rock around PZ-1 exploration well in the Southern Continental Shelf of Korea. To evaluate CO₂ storage capacity of the saline formation, total porosity and CO₂ density are calculated based on well logging data of PZ-1 well. We constructed a 3D geological grid model with a certain size in the x, y and z axis directions for volume estimates of the saline formation, and performed a property modeling to assign total porosity to the geological grid. The estimated average CO₂ geological storage capacity evaluated by the U.S. DOE method for the saline formation covered by the basalt cap rock is 84.17 Mt of CO₂(ranges from 42.07 to 143.79 Mt of CO₂).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.64-70
• /
• 2006

In this study, the $LiCoO_2/LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$ mixed cathode electrodes were prepared and their electrochemical performances were measured in a high cut-off voltage. As the content of $LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$ increased in a mixed cathode, the reversible specific capacity and cycleability of the electrode enhanced, but the rate capability was deteriorated. On the contrary the rate capability of the cathode enhanced, but the reversible specific capacity and cycleability were deteriorated, increasing the content of $LiCoO_2$ in the mixed cathode. The cell of $LiCoO_2/LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$ ($50:50 wt\%$) mixed cathode delivered a discharge capacity of ca. 168 mAh/g at a 0.2 C rate. The capacity of the cell decreased with the current rate and a useful capacity of ca. 152 mAh/g was obtained at a 2.0 C rate. However, the cell showed very stable cycleability: the discharge capacity of the cell after 20th charge/discharge cycling maintains ca. 163 mAh/g.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.682-688
• /
• 2012

In this study we aimed to examine the co-doping effects of 1/6 mol% $Co_3O_4$ and 1/4 mol% $Cr_2O_3$ (Co:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were formed in all systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi = 1.0 by Cr rather than Co. A more homogeneous microstructure was obtained in all systems affected by ${\alpha}$-spinel. In ZBS(CoCr), the varistor characteristics were improved (non-linear coefficient, ${\alpha}$ = 20~63), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.20 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of an electrically single barrier (0.94~1.1 eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phase development, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundary properties were controlled by Co rather than by Cr.