• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.606-612
• /
• 2022

Relatively high indoor CO₂ concentration (>1,000 ppm) has a negative impact on human health. In this work, indoor CO₂ adsorbent was developed by impregnating KOH or K₂CO₃ on commercial activated carbon, named as KOH/AC and K₂CO₃/AC. Commercial activated carbon (AC) showed relatively high BET surface area (929 m²/g) whereas KOH/AC and K₂CO₃/AC presented lower BET surface area of 13.6 m²/g and 289 m²/g. Two experimental methods of TGA (2,000 ppmCO₂, weight basis) and chamber test (initial concentration: 2,000 ppmCO₂, CO₂ IR analyzer) were used to investigate the adsorption capacity. KOH/AC and K₂CO₃/AC exhibited similar adsorption capacities (145~150 mg_CO2/g), higher than K₂CO₃/Al+Si supports adsorbent (84.1 mg_CO2/g_sample). Similarly, chamber test also showed similar trend. Both KOH/AC and K₂CO₃/AC represented higher adsorption capacities (KOH/AC: 93.5 mg_CO2/g K₂CO₃/AC: 94.5 mg_CO2/g_sample) K₂CO₃/Al+Si supports. This is due to the KOH or K₂CO₃ impregnation increased alkaline active sites (chemical adsorption), which is beneficial for CO₂ adsorption. In addition, the regeneration test results showed both K-based adsorbents pose a good regeneration and reusability. Finally, the current study suggested that both KOH/AC and K₂CO₃/AC have a great potential to be used as CO₂ adsorbent for indoor CO₂ adsorption.

• Clean Technology
• /
• v.27 no.3
• /
• pp.255-260
• /
• 2021

A drawback in the CO₂ capture process using an aqueous amine solution is the high energy requirement for the regeneration process. In order to overcome this disadvantage, this study investigated CO₂ capture characteristics using a biphasic absorbent in which isopropanol (IPA) was introduced into an aqueous solution of diethylenetriamine (DETA). When the IPA composition exceeded 20 wt% in 20 wt% DETA aqueous solution, the absorbent phase was liquid-liquid separated into a CO₂-rich phase and a CO₂-lean phase because of the low solubility of the salt formed by the reaction of CO₂ with DETA in isopropanol. When the isopropanol composition in the DETA aqueous solution increased, the phase volume ratio of the CO₂-rich phase to the volume of the CO₂-lean phase increased; and, accordingly, the CO₂ in the CO₂-rich phase was more concentrated. The results of absorbing CO₂ in a packed tower using 20 wt% DETA + IPA + water absorbent confirmed that both the CO₂ absorption capacity and the absorption rate were higher than that of the 20 wt% DETA aqueous solution. When a biphasic absorbent composed of DETA + IPA + water is applied to CO₂ capture, it can be expected to concentrate CO₂ because of phase separation and thereby reduce regeneration energy owing to volume reduction of the CO₂-rich phase.

• Economic and Environmental Geology
• /
• v.53 no.2
• /
• pp.213-220
• /
• 2020

When CO₂ foam is injected into the saline aquifer, the relative permeability of CO₂ decreases and its viscosity increases, thereby reducing mobility in porous media and ultimately improving CO₂ storge with enhanced sweep efficiency. In general, surfactants were used to fabricate CO₂ foam. Recently, nanoparticles have been used to form stable foam than surfactant. This paper introduces CO₂ storage technology using nanoparticle stabilized CO₂ foam. If the surface of the hydrophilic nanoparticles is partially modified into a CO₂-philic portion, the particles have an affinity for CO₂ and water, thus forming a stable CO₂ foam even in deep saline aquifers under high temperature and high salinity conditions, thereby it can be stored in the pores of the rock. In terms of economics, injection method using nanopaticle-stabilized CO₂ foam is more expensive than the conventional CO₂ injection, but it is estimated that it will have price competitiveness because the injection efficiency is improved. From an environmental point of view, it is possible to inject chemical substances such as surfactants and nanomaterials into aquifers or reservoirs for specific purposes such as pollutant removal and oil production. However, some studies have shown that nanoparticles and surfactants are toxic to aquatic animals, so environmentally proven substances should be used. Therefore, further research and development will be needed to study the production and injection of nanoparticle-stabilized CO₂ foam that are environmentally safe and economically reasonable.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.59-71
• /
• 2023

Carbon capture, and storage (CCS) is important for the reduction of greenhouse gases and achieving carbon neutrality. CCS focuses on storing captured CO₂ permanently in underground reservoirs. CO₂-enhanced oil recovery (CO₂-EOR) is one form of CCS, where CO₂ is injected into the underground to enhance oil recovery. CO₂-EOR not only aids in the extraction of residual oil but also contributes to carbon neutrality by storing CO₂ underground continuously. CO₂-EOR can be classified into miscible and immiscible methods, with the CO₂-water alternating gas (CO₂-WAG) technique being a representative approach within the miscible method. In CO₂-WAG, water and CO₂ are alternately injected into the reservoir, enabling oil production and CO₂ storage. The WAG method allows for controlling the breakthrough of injection fluids, providing advantages in oil recovery. It also induces hysteresis in relative permeability during the injection and production process, expanding the amount of trapped CO₂. In this study, the effects of enhancing oil recovery and storing CO₂ underground during CO₂-EOR were presented. Additionally, cases of CO₂-EOR application in relation to CCS were introduced.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.260-266
• /
• 2023

In recent years, excessive emissions of carbon dioxide(CO₂) have become the cause of global climate change. Consequently, there has been significant research activity aimed at both removing and utilizing CO₂. This study assesses the potential utilization of railway tie concrete waste, generated from railway infrastructure, as a CO₂ absorption material and investigates the physicochemical properties before and after CO₂ absorption to understand the CO₂ removal mechanisms. Railway tie concrete waste primarily consists of Si(26.60 %) and contains 9.82 % of Ca. Compared to samples of Cement and Normal concrete waste, it demonstrated superior potential for use as a CO₂ absorption material, with approximately 98 % of the Ca content participating in CO₂ absorption reactions. Through Thermogravimetric Analysis(TGA) and X-ray Diffraction(XRD) analysis, it was confirmed that the carbonate reaction, where the Ca in railway tie concrete waste converts into CaCO₃ through reaction with CO₂ gas, is the primary mechanism for CO₂ removal. Furthermore, Scanning Electron Microscopy(SEM) analysis revealed the formation of numerous CaCO₃ particles with sizes less than 0.1 ㎛ after the CO₂ absorption reaction. This transformation of large internal voids in the CO₂ absorption material into mesopores resulted in an increase in the specific surface area of the material.

• Journal of Environmental Health Sciences
• /
• v.34 no.3
• /
• pp.240-246
• /
• 2008

The purpose of this study was to gain basic information on the characteristics of $CO_2$ adsorption in relation to $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon in a Fixed Bed Reactor. From the results of this study the following conclusions were made: $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon had a longer breakthrough time and more enhanced adsorption capacity than activated carbon alone. When tested with isothermal adsorption and tested for $CO_2$ adsorption the amount of $CO_2$ adsorbed varied with temperature, $CO_2$ inlet concentration, gas flow rate, aspect ratio, etc. Based on the results, when Langmuir, Freundlich and Dubinin-Polanyi adsorption isotherms were used for linear regression of isothermal adsorption data, Langmuir adsorption isotherm was the most suitable. And, the optimum condition for $Na_2CO_3$ and $K_2CO_3$ impregnated activated carbon make-up was 1N and $Li_2CO_3$ was 0.1N. It could be concluded that adsorption capacity was decreased with adsorption temperature and increased gas concentration. When the aspect ratio (L/D) was varied 0.5, 1.0 and 2.0, the significant drop of adsorption amount was observed below 1.0 and breakthrough time was shortened with gas flow rate.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.230-236
• /
• 2021

Ionic conduction mechanism of Mg-Al layered double hydroxides (LDHs) intercalated with CO₃^2- (Mg-Al CO₃^2- LDH) was studied. The electromotive force for the water vapor concentration cell using Mg-Al CO₃^2- LDH as electrolyte showed water vapor partial pressure dependence and obeyed the Nernst equation, indicating that the hydroxide ion transport number of Mg-Al CO₃^2- LDH is almost unity. The ionic conductivity of Mg(OH)₂, MgCO₃ and Al₂(CO₃)₃ was also examined. Only Al₂(CO₃)₃ showed high hydroxide ion conductivity of the order of 10^-4 S cm^-1 under 80% relative humidity, suggesting that Al₂(CO₃)₃ is an ion conducting material and related to the generation of carrier by interaction with water. To discuss the ionic conduction mechanism, Mg-Al CO₃^2- LDH having deuterium water as interlayer water (Mg-Al CO₃^2- LDH(D₂O)) was prepared. After the adsorbed water molecules on the surface of Mg-Al CO₃^2- LDH(D₂O) were removed by drying, DC polarization test for dried Mg-Al CO₃^2- LDH(D₂O) was examined. The absorbance attributed to O-D-stretching band for Mg-Al CO₃^2- LDH(D₂O) powder at around the positively charged electrode is larger than that before polarization, indicating that the interlayer in Mg-Al CO₃^2- LDH is a hydroxide ion conduction channel.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.26 no.2
• /
• pp.71-76
• /
• 2020

CO₂ concentration in kimchi package has emerged recently as a potential index of product ripening to be monitored or sensed in intelligent packaging. Considering that addition of CO₂ absorber into the flexible kimchi package changes behavior of its CO₂ concentration, ripening of kimchi in total acidity, package CO₂ concentration in partial pressure (P_CO2) and package volume at 10℃ were estimated by mathematical model for two size packages included with different CO₂ absorbers. In small size package containing 0.5 kg of kimchi, relatively less gas permeable low density polyethylene (LDPE) sachet of the absorber was found to give rise of P_CO2 linearly correlated with acidity at acceptable conditions of absorber amount and size. The levels of P_CO2 at optimum ripening were different with absorber amount. However, highly gas permeable microporous spunbonded film (Tyvek) sachet did not show the linear relationship except a condition of 1.5 g of CO₂ absorbent. In large size package containing 2.0 kg, absorber sachets of LDPE and Tyvek could give the linear relationship between product acidity and package P_CO2 but at different levels (P_CO2 of package with LDPE sachet: 0.46~0.79 bar, P_CO2 of package with Tyvek sachet: 0.00~0.75 bar). The P_CO2 at optimal ripening was found to be less variable with LDPE sachets than with Tyvek ones. Use of package CO₂ concentration as an indicator of kimchi ripening was shown to be possible on the limited conditions where the linear relationship between them is established or confirmed.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.26 no.2
• /
• pp.105-112
• /
• 2020

As sprout vegetables of interest growing, its maintaining the quality of the technology was needed to solve the problem of increasing growth and maintain quality after harvest. This experiment proved that the quality of radish sprout vegetable was affected by CO₂ treatment during cultivation. Thus, the effect of CO₂ treatment during cultivation on postharvest quality of radish sprout vegetable was investigated in terms of the quality changes in weight loss, gas partial pressure, SPAD, hue angle external appearance during storage at polypropylene film (thickness 30 ㎛) at 10℃. CO₂ treatment used the way to gas with 700 ppm or carbonated water with 700 ppm and 1,400 ppm. The study revealed that growths on CO₂ treated plant were more than those of non-treatment on stem length. After harvesting, the CO₂ treated plant and control growing little different characteristics on fresh weight, plant length and so on. However, there were no differences between the CO₂ treated plant and control on the Fv/Fm and SOD (superoxide dismutase). In gas partial pressure, the O₂ consumption and CO₂ accumulation of the CO₂ treated plant tended to be more than that of non-treated plant. This study also checked that after packaging, the effects of CO₂ treatment during cultivation on the quality of radish sprout vegetable was not significant. However, there were tended to CO₂ treatments were lower value compared to control on SPAD, hue angle and general appearance. CO₂ treatments of radish sprouting vegetable before harvest were improve growth of stem length, but ones were not improving the maintain of quality on radish sprout vegetable during shelf-life period. The results indicated that CO₂ treatment only affected stem elongation until radish sprout vegetable its growth.