• 자원리싸이클링
• /
• 제30권6호
• /
• pp.12-18
• /
• 2021

수성가스 전환 반응은 가스화로 생성된 합성 가스에 수소 생산 증가와 H₂/CO 비율 제어를 위해 수증기를 첨가하는 가스화 후속 공정이다. 본 연구에서는 RPF(Refuse plastic fuel) 가스화 시스템의 합성가스를 대상으로 수성가스 전환 반응을 연구하였다. 수성가스 전환 반응은 촉매를 이용하여 high temperature shift(HTS) 와 low temperature shift(LTS) 반응에 대하여 lab scale 관형 반응기를 이용하여 반응 온도, steam/carbon ratio, 유량의 변화가 H₂ 생성과 CO 전환율에 미치는 영향을 조사하였다. 운전 온도는 HTS 시스템이 250-400℃, LTS 시스템이 190-220℃이며 steam/carbon ratio는 1.5-3.5로 변화시켰다. 반응 모의 가스의 농도는 RPF 합성가스의 농도를 기준으로 CO, 40vol%, H₂, 25vol%, CO₂, 25vol%이다. 반응 온도와 steam/carbon ratio가 증가함에 따라 CO 전환율 및 H₂ 생성량이 증가하고, 유량이 증가하면 촉매층의 체류시간 단축으로 CO 전환율과 H₂ 생성량이 감소하였다.

• 한국환경보건학회지
• /
• 제34권3호
• /
• pp.240-246
• /
• 2008

The purpose of this study was to gain basic information on the characteristics of $CO_2$ adsorption in relation to $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon in a Fixed Bed Reactor. From the results of this study the following conclusions were made: $Na_2CO_3$, $K_2CO_3$, $Li_2CO_3$-impregnated activated carbon had a longer breakthrough time and more enhanced adsorption capacity than activated carbon alone. When tested with isothermal adsorption and tested for $CO_2$ adsorption the amount of $CO_2$ adsorbed varied with temperature, $CO_2$ inlet concentration, gas flow rate, aspect ratio, etc. Based on the results, when Langmuir, Freundlich and Dubinin-Polanyi adsorption isotherms were used for linear regression of isothermal adsorption data, Langmuir adsorption isotherm was the most suitable. And, the optimum condition for $Na_2CO_3$ and $K_2CO_3$ impregnated activated carbon make-up was 1N and $Li_2CO_3$ was 0.1N. It could be concluded that adsorption capacity was decreased with adsorption temperature and increased gas concentration. When the aspect ratio (L/D) was varied 0.5, 1.0 and 2.0, the significant drop of adsorption amount was observed below 1.0 and breakthrough time was shortened with gas flow rate.

• 대한원격탐사학회지
• /
• 제39권2호
• /
• pp.129-142
• /
• 2023

본 연구는 2018년 4월부터 2022년 4월까지 Orbiting Carbon Observatory-2/3의 건조공기 이산화탄소 몰분율(column-averaged carbon dioxide dry-air mole fraction, XCO₂) 자료와 TROPOspheric monitoring instrument의 일산화탄소(carbon monoxide, CO) 및 이산화질소(nitrogen dioxide, NO₂) 연직컬럼농도(본 연구에서 XCO, XNO₂로 명명) 자료를 활용하여 한국과 중국의 도시 및 권역에 대해 CO와 CO₂, CO와 NO₂의 비율을 분석하고, 사회경제적 지표(인구, 차량 등록 대수, 지역내총생산)와 비율의 관계, 한국과 중국에서의 특성 차이를 제시하였다. 먼저 CO₂, CO 그리고 NO₂ 세 기체상 물질의 대기 중 체류시간 차이로 CO₂, CO는 배경값과 추세선을 제거한 ΔXCO₂, ΔXCO로 분석하였다. 지역별로 세 값을 비교한 결과 ΔXCO, ΔXCO₂는 중국 지역이 XNO₂는 한국 지역이 상대적으로 높은 값을 보였으며, 두 값의 비율(ΔXCO/ΔXCO₂, ΔXCO/XNO₂) 모두 한국보다 중국에서 높은 것으로 나타났다. ΔXCO/ΔXCO₂, ΔXCO/XNO₂와 사회경제적 지표는 양의 상관관계를 보였으며, 이는 도시 규모가 크고 경제활동이 활발할수록 대기오염기체 및 온실기체의 농도가 높다는 점을 시사한다. 한국과 중국의 비율 특성 차이를 분석하기 위해 두 나라의 지역별로 분석한 ΔXCO와 ΔXCO₂ 관계는 한국은 음의 관계성을 중국은 양의 관계성을 나타냈다. ΔXCO와 XNO₂의 상관성을 여름과 겨울에 대해 각각 살펴본 결과, 한국은 계절에 따른 ΔXCO 증감이 크지 않은 것에 비해 중국은 북동부 지역을 중심으로 계절에 따른 ΔXCO와 XNO₂의 증감이 크게 나타나며 관계성의 차이를 보였다. 이는 온실기체와 대기오염기체의 비율을 분석할 때, 계절 변동성 및 국가별 배출 특성을 감안해야 함을 시사한다.

• 대기
• /
• 제31권5호
• /
• pp.625-635
• /
• 2021

South Korea established the 2050 Carbon Neutral Plan in response to the climate crisis, and to achieve this policy, it is very important to monitor domestic carbon emissions and atmospheric carbon concentration. Both CO₂ and CO are emitted from fossil fuel combustion processes, but the relative ratios depend on the combustion efficiency and the strength of local emission regulations. In this study, the relationship between CO₂ and CO was analyzed using ground observation data for the period of 2018~2020 at Anmyeon-do site and the CO/CO₂ ratio according to regional origin during high CO₂ cases was investigated based on the footprint simulated from Stochastic Time-Inverted Lagrangian Transport (STILT) model. CO₂ and CO showed a positive correlation with correlation coefficient of 0.66 (p < 0.01), and averaged footprints during high CO₂ cases confirmed that air particles mainly originated from eastern and north-eastern China, and inland of Korean Peninsula. In addition, it was revealed that among the cases of high CO₂ concentration, when the CO/CO₂ ratio is high, the industrial area of eastern China is greatly affected, and when the ratio is low, the contribution of the domestic region is relatively high. The ratio of CO₂ and CO in this study is significant in that it can be used as a useful factor in determining the possibility of domestic and foreign origins of climate pollutants.

• 한국수소및신에너지학회논문집
• /
• 제34권4호
• /
• pp.327-333
• /
• 2023

The water gas shift reaction was carried out using the commercial catalyst pellet and the simulated gases expected to occur from waste plastic gasification. In the water gas shift reaction, the high temperature shift reaction and the low temperature shift reaction were continuously performed with CO:H₂O ratio of 1:2, 1:2.5, and 1:3, and the CO conversion and H₂ increase rate were evaluated. The H₂ increase rate increased in order to CO:H₂O ratio of 1:3 > CO:H₂O ratio of 1:2.5 > CO:H₂O ratio of 1:2. The CO conversion showed a high value of more than 97% at each CO:H₂O ratio. The water gas shift reaction at a CO:H₂O ratio of 1:3 showed the highest H2 increase rate and CO conversion.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.21-26
• /
• 2020

The objective of this work is to numerically reveal the effect of equivalence ratio change on the simultaneous reduction of NO_X and soot emissions from the simulated-EGR compression ignition engine containing CO₂. An experiment was conducted by using a single-cylinder common-rail injection system engine, an intake control system, and exhaust emissions analyzers. The numerical analysis results were validated under the same experimental conditions. To investigate the effect of equivalence ratio by simulated-EGR containing CO₂, the O₂, N₂, and CO₂ mole fraction were changed in the initial air conditions to the cylinder. The results were analyzed in terms of peak cylinder pressure, indicated mean effective pressure, indicated specific nitrogen oxide, and indicated specific soot. It was revealed that ignition delay characteristics and heat release rate (ROHR) characteristics were not significantly different according to the equivalence ratio. However, as the equivalence ratio increased from 0.68 to 0.83, the maximum combustion pressure and IMEP decreased by about 6.5% and 9.4%, respectively. In the case of ISFC, as is well known, the trend is opposite of IMEP. In the case of ISNO, as the equivalence ratio increased, less NO was generated, and as the equivalence ratio increased by 0.05, the ISSoot value of about 10% increased.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.737-743
• /
• 2006

[ $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ ] powder was prepared using a simple combustion method. specially, ratio of 2:1, 3:2, 1:1, 2:3, 1:2 was adopted as acetate source/nitrate source. The diffraction pattern of $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ powder showed that this compound could be classified as hexagonal $a-NaFeO_2$ structure (space group : $R\bar{3}m$). The size of powder was less than $1{\mu}m$. Small particle size of cathode powder would give a good ionic and electronic conductivity to cathode electrode, which made of cathode powder. As the increase of nitrate source-ratio, discharge capacity of $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ at high charge-discharge rate was increased. When the ratio of acetate source/nitrate source was 1:2, discharge capacity at 10 C rate (2000 mA/g) was 180 mAh/g. It was $10{\sim}15%$ larger than that of powder, which have 2:1 as acetate source/nitrate ratio.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.43-45
• /
• 2012

As a part of recent CO₂ emission reduction studies in the concrete industry with active use of concrete admixtures with low basic unit of CO₂ emission such as blast furnace slag (BFS), basic unit of CO₂ emission by SBFS was computed in order to assess CO₂ emission by reinforced concrete building with smart blast furnace slag (SBFS). In addition, SBFS concrete was applied to the subject building for assessment of CO₂ emission during material production step among construction steps. Life cycle CO₂ emission assessment on the subject building was classified into 7cases according to mix ratio of BFS and SBFS.

• 한국수소및신에너지학회논문집
• /
• 제35권2호
• /
• pp.140-145
• /
• 2024

High temperature co-electrolysis of H₂O-CO₂ mixtures using solid oxide cells has attracted attention as promising CO₂ utilization technology for production of syngas (H₂/CO), feedstock for E-fuel synthesis. For direct supply to E-fuel production such as hydrocarbon and methanol, the outlet gas ratio (H₂/CO/CO₂) of co-electrolysis should be controlled. In this work, current voltage characteristic test and product gas analysis were carried out under various reaction conditions which could attain proper syngas ratio.

• 청정기술
• /
• 제27권3호
• /
• pp.255-260
• /
• 2021

아민 수용액을 이용한 CO₂ 포집 공정의 문제점은 재생에 따른 높은 에너지 요구량이다. 이러한 단점을 극복하기 위해서 본 연구에서는 디에틸렌트리아민(diethylenetriamine, DETA) 수용액에 이소프로판올(isopropanol, IPA)을 도입한 상분리 흡수제 적용에 따른 CO₂ 포집 특성을 고찰하였다. 20 wt% DETA 수용액에서 IPA 조성이 20 wt%를 이상이 되면 CO₂를 흡수함에 따라 흡수제의 상이 CO₂-농축상과 CO₂-희박상으로 액-액 분리된다. 그 이유는 CO₂와 DETA가 반응하여 형성된 염의 IPA에 대한 낮은 용해도 때문이다. DETA 수용액에서 IPA 조성이 증가하면 CO₂-희박상의 부피에 대한 CO₂-농축 상의 부피비가 증가하게 되고 이에 따라 CO₂-희박상에서의 CO₂ 농축 정도가 높아지게 된다. 20 wt% DETA + IPA + 물 흡수제를 이용하여 흡수탑에서 CO₂를 흡수한 결과 20 wt% DETA 수용액 흡수제에 비해 CO₂ 흡수능 및 흡수속도가 모두 높은 것으로 확인되었다. DETA + IPA + 물로 구성된 상분리 흡수제를 CO₂ 포집에 적용할 경우 상분리 따른 CO₂ 농축과 CO₂-농축상의 부피 감소에 따른 재생에너지 저감을 기대할 수 있다.