• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1296-1300
• /
• 2004

SnO$_2$ is one of the most suitable gas sensor materials. The microstructure and surface morphology of films must be controlled because the electrical and optical properties of SnO$_2$ films depend on these characteristics. The effects of chemical mechanical polishing(CMP) on the variation of morphology of SnO$_2$ films prepared by RF sputtering system were investigated. The commercially developed ceria-based oxide slurry, silica-based oxide slurry, and alumina-based tungsten slurry were used as CMP slurry. Non-uniformities of all slurries met stability standards of less than 5 %. Silica slurry had the highest removal rate among three different slurries, sufficient thin film topographies and suitable root mean square(RMS) values.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.86-89
• /
• 2003

Chemical Mechanical Planarization(CMP) has been accepted as the most effective processes for ultra large scale integrated (ULSI) chip manufacturing. However, as the polishing process continues, pad pores get to be glazed by polishing residues, which hinder the supply of new slurry. And pad surface is ununiformly deformed as real contact distance. These defects make material removal rate(MRR) decrease with a number of polishied wafer. Also the desired within-chip planarity, within wafer non-uniformity(WIWNU) and wafer to wafer non-uniformity(WTWNU) arc unable to be achieved. So, pad conditioning in CMP Process is essential to overcome these defects. The eletroplated or brazed diamond conditioner is used as the conventional conditioning. And. allumina long fiber, the jet power of high pressure deionized water, vacuum compression. ultrasonic conditioner aided by cavitation effect and ceramic plate conditioner are once used or under investigation. But. these methods arc not sufficient for ununiformly deformed pad surface and the limits of conditioning effect. So this paper focuses on the characteristics of diamond conditioner which reopens glazed pores and removes ununiformly deformed pad away.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.343-346
• /
• 2003

A systematic study of Cu CMP in terms of the effect of slurry chemicals(oxidizer, corrosion inhibitor, complexing agent) on the process characteristics has been performed. In acidic media, a corrosion inhibitor, benzotriazole(BTA) and tolytriazol(TTA) was used to control the removal rate and avoid isotropic etching. When complexing agent is added with $H_2O_2$ 2wt% in the slurry, a corrosion rate was presented very good. Most of in, it was appeared that BTA is possible to be replaced by TTA. The tartaric acid was distinguished for the effect among complexing agents. n we apply this results to copper CMP process, it is thought that we will be able to obtain better yield.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.168-173
• /
• 2001

The chemical mechanical polishing (CMP) is generally consisted of pad, slurry including abrasives and so on. However, there are some problems in a general CMP: defects, a high Cost of Consumable (CoC), an environmental problem. The slurry including abrasives especially gives rise to not only increase a CoC, but also prohibition from achieving an eco-process. This paper introduces an abrasive capsulation pad to achieve an eco-process decreasing abrasives used is CMP. The binder wth a water a water swelling and a water soluble characteristic is used for an auto-conditioning, and the $CeO_2$abrasive is selected for an abrasive capsulation pad. Comparing with a conventional CMP, an abrasive capsulation pad appears good characteristics in ILD CMP and is able to achieve an eco-process decreasing wasted slurry.

• Journal of Microbiology and Biotechnology
• /
• v.15 no.3
• /
• pp.573-578
• /
• 2005

Pyrimidine nucleotide N-ribosidase (pyrimidine 5'-nucleotide phosphoribo(deoxyribo)hydrolase/pyrimidine 5'-nucleotide nucleosidase, EC 3.2.2.10) catalyzes the breakdown of pyrimidine 5'-nucleotide into pyrimidine base and ribose(deoxyribo)-5-phosphate. However, detailed characteristics of the enzyme have not yet been reported. The enzyme was purified to homogeneity 327.9-fold with an overall yield of $6.1\%$ from Pseudomonas oleovorans ATCC 8062. The enzyme catalyzed cytidine monophosphate (CMP) and uridine monophosphate (UMP), but not adenosine monophosphate (AMP) and guanosine monophosphate (GMP). The enzyme optimally metabolized CMP at pH 6.0 and UMP at around 8.5, and the optimum temperature for the overall enzyme reaction was found to be $37^{\circ}C$. The $K_m$ values of the enzyme for CMP (at pH 6.0) and UMP (at pH 8.5) were 1.6 mM and 1.1 mM, respectively. AMP, deoxyCMP, and deoxyUMP were very effective inhibitors of the reaction. Double-reciprocal plots obtained in the absence and in the presence of AMP revealed that this inhibitory effect was of the mixed competitive type with respect to the breakdown of CMP and of the noncompetitive type with respect to the breakdown of UMP. In the presence of AMP, the enzyme followed sigmoid kinetics with respect to each substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.568-574
• /
• 2000

We have been optimized tungsten(W) plug CMP(chemical mechanical polishing) characteristics using two different kinds of component of slurry and two different kinds of pad which have different hardness. The comparison of oxide film roughness on around W plug after polishing has been carried out. And W plug recess for consumable sets and dishing effect at dense area according to the rate of over-polishing has been investigated. Also the analysis of residue on surface after cleaning have been performed. As a experimental result we have concluded that the consumable set of slurry A and hard pad was good for W plug CMP process. After decreasing the rate of chemical reaction of silica slurry and adding two step buffering we could reduce the expanding of W plug void however we are still recognizing to need a more development for those kinds of CMP consumables.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.41-44
• /
• 2003

As the device feature size is reduced to the deep sub-micron regime, the chemical mechanical polishing (CMP) technology is widely recognized as the most promising method to achieve the global planarization of the multilevel interconnection for ULSI applications. However, cost of ownership (COO) and cost of consumables (COC) were relatively increased because of expensive slurry. In this paper, the effects of different slurry composition on the oxide CMP characteristics were investigated to obtain the higher removal rate and lower non-uniformity. We prepared the various kinds of slurry. In order to save the costs of slurry, the original slurry was diluted by de-ionized water (DIW). And then, alunima abrasives were added in the diluted slurry in order to promote the mechanical force of diluted slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.50-53
• /
• 2003

CMP (chemical mechanical polishing) process remained to solve several problems in deep sub-micron integrated circuit manufacturing process. especially consumables (polishing pad, backing film, slurry, pad conditioner), one of the most important components in the CMP system is the slurry. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are important in determining polish rate and planarization ability of a CMP process. However, the cost of abrasives is still very high. So, in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.145-148
• /
• 2003

Recently, the recycle of CMP (chemical mechanical polishing) slurries have been positively considered in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in CMP process. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are one of the most important components. Especially, the abrasive particles of slurry are needed in order to achieve a good removal rate. However, the cost of abrasives, is still very high. In this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slury, As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.527-527
• /
• 2007

CMP가 1980년 IBM에 의해 반도체 웨이퍼의 표면 연마를 위해 적용된 후, 많은 연구 개발의 노력으로 반도체 집적회로의 제조 공정에서 필수 핵심기술이 되었으나, 소모자재(연마패드, 탄성지지대, 슬러리, 패드 컨디셔너)의 비용이 CMP 공정 비용의 70% 이상을 차지하는 등 제조단가가 높다는 단점을 극복할 수가 없었다. 특히, 고가의 슬러리가 차지하는 비중이 40% 이상을 넘고 있어, 슬러리 원액의 소모량을 줄이기 위한 연구들이 현재 활발히 연구 중이다. 슬러리의 변수로는 연마입자의 종류 및 특성, 용액의 pH, 연마입자의 슬러리내 안정성 등이 있다. 슬러리내 연마입자는 연마량과 균일도 측면에서 밀접한 관계를 가지고 있다. 또한, 연마제의 영향에 따라 연마율의 차이 즉, CMP 특성의 변화를 보이고 있기 때문에 투입량 또한 최적화가 필요하다. 본 연구에서는 새로운 연마제의 특성을 알아보기 위해 탈이온수(de-ionized water; DIW)에 $CeO_2,\;MnO_2,\;ZrO_2$ 등을 첨가한 후 분산시간에 따른 연마 특성과 atomic force microscopy (AFM)분석을 통해 표면 거칠기를 비교 분석하였다. 그리고, 세 가지 종류의 연마제를 각각 1wt%, 3wt%, 5wt% 첨가하여 산화막에 대한 CMP 특성을 알아본 후, scanning electron microscopy (SEM) 측정과 입도 분석을 통해 그 가능성을 알아보았다.