• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.527-527
• /
• 2007

CMP가 1980년 IBM에 의해 반도체 웨이퍼의 표면 연마를 위해 적용된 후, 많은 연구 개발의 노력으로 반도체 집적회로의 제조 공정에서 필수 핵심기술이 되었으나, 소모자재(연마패드, 탄성지지대, 슬러리, 패드 컨디셔너)의 비용이 CMP 공정 비용의 70% 이상을 차지하는 등 제조단가가 높다는 단점을 극복할 수가 없었다. 특히, 고가의 슬러리가 차지하는 비중이 40% 이상을 넘고 있어, 슬러리 원액의 소모량을 줄이기 위한 연구들이 현재 활발히 연구 중이다. 슬러리의 변수로는 연마입자의 종류 및 특성, 용액의 pH, 연마입자의 슬러리내 안정성 등이 있다. 슬러리내 연마입자는 연마량과 균일도 측면에서 밀접한 관계를 가지고 있다. 또한, 연마제의 영향에 따라 연마율의 차이 즉, CMP 특성의 변화를 보이고 있기 때문에 투입량 또한 최적화가 필요하다. 본 연구에서는 새로운 연마제의 특성을 알아보기 위해 탈이온수(de-ionized water; DIW)에 $CeO_2,\;MnO_2,\;ZrO_2$ 등을 첨가한 후 분산시간에 따른 연마 특성과 atomic force microscopy (AFM)분석을 통해 표면 거칠기를 비교 분석하였다. 그리고, 세 가지 종류의 연마제를 각각 1wt%, 3wt%, 5wt% 첨가하여 산화막에 대한 CMP 특성을 알아본 후, scanning electron microscopy (SEM) 측정과 입도 분석을 통해 그 가능성을 알아보았다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.111-111
• /
• 2008

태양전지는 태양에너지를 직접 전기에너지로 변환시켜주는 광전 소자로서 구조적으로 단순하고 제조 공정도 비교적 간단하지만, 실용화를 위해서는 비용적인 측면이 많은 걸림돌이 되고 있다. 기존의 실리콘 태양전지는 낮은 광흡수율, 고비용임에도 불구하고 가장 많이 활용되고 있는 태양전지 기술이다. 그러나 태양전지의 경제성 향상과 실용화를 위해서는 기존의 실리콘 태양전지 보다 고효율 및 고신뢰도의 박막형 태양전지의 개발이 필요하다. 박막헝 태양전지의 재료로는 비정질 실리콘, 다결정 실리콘. CIGS, CdTe 등이 있다. 그 중에서도 박막형 태양전지에 광흡수층 물질로는 밴드갭 에너지 (l.4eV 부근), 변환 효율, 경제성 등을 고려했을 때 II-VI족 화합물인 CdTe가 가장 적합한 것으로 각광받고 있다. 하지만 아직까지 실리콘 태양전지에 비해 효율이 많이 떨어지는 단점을 가지고 있기 때문에 효율을 더 끌어올리기 위한 연구가 활발히 진행되고 있는 실정이다. 또한 CMP(chemical mechanical polishing) 공정은 반도체 박막 분야뿐만 아니라 물리, 화학 반응의 기초 연구에도 널리 응용이 되는 기술로써, 시료와 연마 패드 사이의 회전마찰에 의한 기계적 연마와 연마제 (abrasive) 에 의한 화학적 에칭으로 박막 표면을 평탄화하는 기술이다. 본 연구에서는 sputtering 법에 의해 증착된 CdTe 박막에 CMP 공정을 적용하여 표면 특성을 개선한 뒤 태양전지 변환 효율과 직접적인 연관성을 가지고 있는 표면 및 광특성의 변화를 CMP 공정 전과 후로 비교하였다. 표면의 변화를 관찰하기 위해서 AFM(atomic forced microscope) 과 SEM(scanning electron microscopy) 을 이용하였으며, 광특성의 비교를 위해서 흡수율과 PL특성을 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.382-385
• /
• 2003

Chemical mechanical polishing(CMP) is an essential process in the production of copper-based chips. On this work, the stability of Hydrogen Peroxide($H_2O_2$) as oxidizer of Cu CMP slurry has been investigated. $H_2O_2$ is known as the most common oxidizer in Cu CMP slurry. Copper slowly dissolves in $H_2O_2$ solutions and the interaction of $H_2O_2$ with copper surface had been studied in the literature. Because hydrogen peroxide is a weak acid in aqueous solutions, a passivation-type slurry chemistry could be achieved only with pH buffered solution.[1] Moreover, $H_2O_2$ is so unstable that its stabilization is needed using as oxidizer. As adding KOH as pH buffering agent, stability of $H_2O_2$ decreased. However, stability went up with putting in small amount of BTA as film forming agent. There was no difference of $H_2O_2$ stability between KOH and TMAH at same pH. On the other hand, $H_2O_2$ dispersion of TMAH is lower than that of KOH. Furthermore, adding $H_2O_2$ in slurry in advance of bead milling lead to better stability than adding after bead milling. Generally, various solutions of phosphoric acids result in a higher stability. Using Alumina C as abrasive was good at stabilizing for $H_2O_2$; moreover, better stability was gotten by adding $H_3PO_4$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.543-543
• /
• 2008

반도체 집적회로의 제조 공정 중 CMP 공정이 필수 핵심기술이 되었다. 이처럼 CMP 공정 기술이 다층 배선 구조의 광역 평탄화를 위해서는 매우 효과적이지만 기계적인 연마패드와 화학적인 식각 작용을 하는 슬러리를 이용하여 연마가 진행되므로 공정 결함이 문제시되어 왔다. 그 중에서도, 소모자재의 비용이 CMP 공정비용의 70% 이상을 차지하는 제조단가가 높다는 단점이 있다. 특히 고가의 슬러리가 차지하는 비중이 40% 이상을 넘고 있어, 슬러리 원액의 소모량을 줄이기 위한 연구들이 현재 활발히 연구 중에 있다. 본 논문에서는 새로운 혼합 연마제 슬러리에 대한 CMP 특성을 통해 기존에 상용화된 슬러리의 CMP 특성과 비교 고찰하여 MAS의 우수성을 입증하고, 최적화된 공정기술 연구의 기반으로 활용하고자 실리카 슬러리에 $MnO_2$ 연마제를 혼합하여 연마특성을 비교분석하였고, AFM, EDX, XRD, TEM분석을 통해 그 가능성을 알아보았다.

• Proceedings of the KAIS Fall Conference
• /
• 2006.11a
• /
• pp.272-275
• /
• 2006

본 논문에서는 CMP(Chemical Mechanical Polishing) 슬러리용으로 사용되는 저가이면서 입도 분포가 균일한 콜로이달 실리카(Colloidal Silica)를 사용하여 추가의 첨가제 없이 열처리 공정만을 거쳐 석영유리를 제조하여 6N의 순도와 1 mm 두께 기준 86%의 자외선 투과율 그리고 AFM(Atomic Force Microscopy) 및 간섭계 현미경을 이용하여 표면의 거칠기가 1 nm 미만인 고순도 석영유리를 제조하였다.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.41-44
• /
• 2015

Silicon trench process for bulk fin field effect transistor (finFET) is suggested without using chemical mechanical polishing (CMP) that cause contamination problems with chemical stuff. This process uses thickness difference of photo resistor spin coating and silicon nitride sacrificial layer. Planarization of silicon oxide and silicon trench formation can be performed with etching processes. In this work 50 nm silicon trench is fabricated with AZ 1512 photo resistor and process results are introduced.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.1
• /
• pp.5-10
• /
• 2007

Using a reference slurry, ammonium dodecyl sulfate (ADS), an anionic and environmentally friendly surfactant, was investigated as an alternative to BTA for its inhibition and lubrication characteristics. Results demonstrated that the inhibition efficiency of ADS was superior to that of BTA. Coefficient of friction (COF) was the lowest when the slurry contained ADS. This suggested that adsorbed ADS on the surface provided lubricating action thereby reducing the wear between the contacting surfaces. Temperature results were consistent with the COF and removal rate data. ADS showed the lowest temperature rise again confirming the softening effect of the adsorbed surfactant layer and less energy dissipation due to friction. Spectral analysis of shear force showed that increasing the pad-wafer sliding velocity at constant wafer pressure shifted the high frequency spectral peaks to lower frequencies while increasing the variance of the frictional force. Addition of ADS reduced the fluctuating component of the shear force and the extent of the pre-existing stick-slip phenomena caused by the kinematics of the process and collision event between pad asperities with the wafer. By contrast, in the case of BTA, there were no such observed benefits but instead undesirable effects were seen at some polishing conditions. This work underscored the importance of real-time force spectroscopy in elucidating the adsorption, lubrication and inhibition of additives in slurries in CMP.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.68-69
• /
• 2005

BTO ($BaTiO_3$) thin film is one of the high dielectric materials for high-density dynamic random access memories (DRAMs) due to its relatively high dielectric constant. It is generally known that BTO film is difficult to be etched by plasma etching, but high etch rate with good selectivity to pattern mask was required. The problem of sidewall angle also still remained to be solved in plasma etching of BTO thin film. In this study, we first examined the patterning possibility of BTO film by chemical mechanical polishing (CMP) process instead of plasma etching. The sputtered BTO film on TEOS film as a stopper layer was polished by CMP process with the self-developed $BaTiO_3$- and $TiO_2$-mixed abrasives slurries (MAS), respectively. The removal rate of BTO thin film using the$ BaTiO_3$-mixed abrasive slurry ($BaTiO_3$-MAS) was higher than that using the $TiO_2$-mixed abrasive slurry ($TiO_2$-MAS) in the same concentrations. The maximum removal rate of BTO thin film was 848 nm/min with an addition of $BaTiO_3$ abrasive at the concentration of 3 wt%. The sufficient within-wafer non-uniformity (WIWNU%)below 5% was obtained in each abrasive at all concentrations. The surface morphology of polished BTO thin film was investigated by atomic force microscopy (AFM).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.101-102
• /
• 2006

BTO ($BaTiO_3$) thin film is one of the high dielectric materials for high-density dynamic random access memories (DRAMs) due to its relatively high dielectric constant, It is generally known that BTO film is difficult to be etched by plasma etching, but high etch rate with good selectivity to pattern mask was required. The problem of sidewall angle also still remained to be solved in plasma etching of BTO thin film. In this study, we first examined the patterning possibility of BTO film by chemical mechanical polishing (CMP) process instead of plasma etching. The sputtered BTO film on TEOS film as a stopper layer was polished by CMP process with the sell-developed $BaTiO_3$- and $TiO_2$-mixed abrasives slurries (MAS). respectively. The removal rate of BTO thin film using the $BaTiO_3$-mixed abrasive slurry ($BaTiO_3$-MAS) was higher than that using the $TiO_2$-mixed abrasive slurry ($TiO_2$-MAS) in the same concentrations. The maximum removal rate of BTO thin film was 848 nm/min with an addition of $BaTiO_3$ abrasive at the concentration of 3 wt%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.117-117
• /
• 2008

In MIM capacitor, poly-Si bottom electrode is replaced with metal bottom electrode. Noble metals can be used as bottom electrodes of capacitors because they have high work function and remain conductive in highly oxidizing conditions. In addition, they are chemically very stable. Among novel metals, Ru (ruthenium) has been suggested as an alternative bottom electrode due to its excellent electrical performance, including a low leakage of current and compatibility to high dielectric constant materials. Chemical mechanical planarization (CMP) process has been suggested to planarize and isolate the bottom electrode. Even though there is a great need for development of Ru CMP slurry, few studies have been carried out due to noble properties of Ru against chemicals. In the organic chemistry literature, periodate ion ($IO_4^-$) is a well-known oxidant. It has been reported that sodium periodate ($NaIO_4$) can form $RuO_4$ from hydrated ruthenic oxide ($RuO_2{\cdot}nH_2O$). $NaIO_4$ exist as various species in an aqueous solution as a function of pH. Also, the removal mechanism of Ru depends on solution of pH. In this research, the static etch rate, passivation film thickness and wettability were measured as a function of slurry pH. The electrochemical analysis was investigated as a function of pH. To evaluate the effect of pH on polishing behavior, removal rate was investigated as a function of pH by using patterned and unpatterned wafers.