• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.247-252
• /
• 2004

To secure stability and availability of Rammed Aggregate Pier method as the foundation of a structure, the bearing capacity and failure behavior characteristics was studied through soil laboratory tests in a model ground. In this study, soil laboratory tests use carried out to find the applicability of RAP method as the foundation of a structure. And bearing capacity and the failure mechanism of RAP method was studied according to relative density($60\%,\;70\%,\;90\%$), diameter(45mm, 60mm, 70mm) of each pier ana depth(5cm, l0cm, 15cm, 20cm, 25cm, 30cm). Earth pressure cell is set up approach RAP and 1.0D space at RAP center. Bearing acpacity and the failure mechanism of RAP is investigated by load test As a result, bulging failure was happened in $5\~10cm\;(1.0D\~2.00)$ depth which the maximum lateral earth pressure is acting. Especially, diameter changing of RAP are in inverse proportion to the relative density and the lateral stress is very much influenced by the lateral earth pressure in every layer and tends to decrease according to depth.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.57-66
• /
• 2001

In order to measure steel corrosion in mortar by a transient electro-magnetic (TEM) Method, the development of the sensors have been studied. The sensors were made of enamelled wire with diameter of 0.25mm and Acril. The sensor configuration was used as a coincident loop type. The secondary electro motive force(EMF) was measured with SIROTEM III. The accelerator was equipped with the SIROTEM III. The accelerator permits the transmitter to turn off approximately 10~15 times faster than normal. The high resolution time series used for very shallow or high resistivity investigation was selected. The steels were embedded in mortar which were made from sand : cement : water ratio of 2 : 1: 0.5. The mortar specimen was 50cm long, 20cm wide and 10cm thick. To investigate steel corrosion in mortar, the sensors used were with 2$\times$2$cm^2$(3, 6, 9$\Omega$), 3$\times$3$cm^2$(3, 6, 9$\Omega$) and 6$\times$6$cm^2$(3, 6, 9$\Omega$). The obtained result obtained showed that the sensor 8(6$\times$6$cm^2$, 6$\Omega$) was the proper sensor for the measurement of steel corrosion in mortar.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3525-3534
• /
• 2023

Non-uniformity of Pu and Cm composition in used nuclear fuel was analyzed to determine its effect on Pu accountancy in pyroprocessing, while employing the Pu-to-²⁴⁴Cm ratio method. Burnup simulation of a typical pressurized water reactor fuel assembly, required for the analysis, was carried out using MCNP code. Used fuel nuclide composition, as a function of nine axial and two radial meshes, were evaluated. The axial variation of neutron flux and self-shielding effects were found to affect the uniformity of Pu and Cm compositions and in turn the Pu-to-²⁴⁴Cm ratio. However, the results of the study showed that these non-uniformities do not affect the use of Pu-to-²⁴⁴Cm ratio method for Pu accountancy, if the measurement samples are drawn from the voloxidized powder at the feed step of pyroprocessing. 'Material Unaccounted For' and its uncertainty estimates are also presented for a pyrprocessing facility to verify safeguards monitoring requirements of the IAEA.

• Journal of radiological science and technology
• /
• v.1 no.1
• /
• pp.69-73
• /
• 1978

This study was conducted in order to determine width, length of lung by radiographic method. The measurements carried out on normal chest X-ray film of 1,036 persons who took the radiograph from the April of 1977 to the June of 1978. As a result of this study, the following conclusions were obtained: 1. In the case of male, the average width, and length of both side lung size from new birth to nineteen of age was larger than female with the exception of partly age group. 2. Lung size in average width at adult was from 27.60cm to 29.20cm and female was 25.10cm to 26.22cm. 3. The mean length of left lung at adult was from 26.32cm to 25.27cm in female. 4. The average length of right lung at adult was from 25.8cm to 28.35cm in male and female was from 24.86cm to 25.17cm. 5. It was found that lung sige in width and length was slightly increased until 39 years of age, but was trend to decrease it of lung in the age of 40 years old. 6. In the case of adult, the difference of the average length between right and left lung, the length of right lung was slightly shorter than left that.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.3
• /
• pp.295-303
• /
• 2018

In the DBB delivery system, the design stage and the construction stage are separated. Because of this, design changes frequently occur, and problems such as construction cost overrun, schedule delay, and quality deterioration happen as well. Recently, in the construction industry CM at Risk(CM@R) delivery system, which can systematically solve the above-mentioned problems of DBB delivery system, meet various demands of clients, and overcome the limited cost and period. In the CM@R delivery system, the contractor negotiates for a maximum guaranteed price(GMP) with the client at the design stage, and the CM performer carries out the construction within the GMP. However, uncertainties are inherent in the GMP calculation because the calculation is based on unfinished drawings and documents. In this study, a Probabilistic Earlier GMP Calculation Method by combining a probabilistic tool of Monte Carlo simulation with a case based reasoning is proposed so that the uncertainty in GMP calculation is reflected. After the earlier GMP is calculated, a process to calculate the $2^{nd}$ GMP at the time of around 80 % of detailed deign and to negotiate with the client to fix the final GMP is proposed. The Probabilistic Earlier GMP Calculation Method is verified through the case study. In this study, researchers set the range of GMP through the proposed probabilistic GMP calculation and tried to reduce the risk through negotiation between the client and the CM performer. The proposed method and process would contribute to the successful introduction of CM@R in Korea.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.96-97
• /
• 2019

Pulse Width Modulation (PWM) is a widely adopted technique to drive the motor using the voltage source inverters. Since they generate high frequency Common Mode (CM) Voltage, a high shaft voltage in induction motor is induced which leads to parasitic capacitive currents causing adverse effects such as premature deterioration of ball bearings and high levels of electromagnetic emissions. This paper presents an Active Cancellation Circuit (ACC) which can significantly reduce the CM voltage hence the common mode current in the three phase induction motor drives. In the proposed method the CM voltage is detected by the capacitors and applied to the frame of the motor to cancel the CM voltage hence the CM current. Unlike the conventional methods the proposed method does not insert the transformer in between the inverter and motor, a high power rating three phase transformer is not required and no losses associated with it. In addition the proposed method is applicable to any kind of PWM motor drives regardless of their PWM methods. The effectiveness of the proposed method is proved by the experiments with a three phase induction motor (1.1kW 415V/60Hz) combined with a three phase voltage source inverter modulated by the Space Vector Modulation (SVM).

• Current Optics and Photonics
• /
• v.6 no.3
• /
• pp.244-251
• /
• 2022

We introduce a spectral reconstruction method to enhance the spectral resolution in a static modulated Fourier-transform spectrometer. The optical-path difference and the interferogram in the focal plane, as well as the relationship of the interferogram and the spectrum, are discussed. Additionally, for better spectral reconstruction, applications of phase-error correction and apodization are considered. As a result, the transfer function of the spectrometer is calculated, and then the spectrum is reconstructed based on the relationship between the transfer function and the interferogram. The spectrometer comprises a modified Sagnac interferometer. The spectral reconstruction is conducted with a source with central wave number of 6,451 cm^-1 and spectral width of 337 cm^-1. In a conventional Fourier-transform method the best spectral resolution is 27 cm^-1, but by means of the spectral reconstruction method the spectral resolution improved to 8.7 cm^-1, without changing the interferometric structure. Compared to a conventional Fourier-transform method, the spectral width in the reconstructed spectrum is narrower by 20 cm^-1, and closer to the reference spectrum. The proposed method allows high performance for static modulated Fourier-transform spectrometers.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.773-778
• /
• 2002

The variance characteristics of the calcium carbonate contents along to the concrete cover depth takes the prediction method of remaining service life of concrete. Calcium carbonate contents were measured by the Thermo Gravimetric/Differential Thermal Analysis method at three point, depth of 0.25cm, 0.75cm, 1.25cm from the surface of concrete. This prediction method contain some assumption that the chemical protection conferred on steel is through a passive protective oxide film which forms on steel in an environment at or above a pH of 10.5$^{4)}$ .

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.1
• /
• pp.51-62
• /
• 2020

This study was conducted to develop a method for depth assessment of embedded sources using gamma-spectrum ratio and for the evaluation of field applicability. To this end, Peak to Compton and Peak to valley ratio changes were evaluated according to ¹³⁷Cs, ⁶⁰Co, ¹⁵²Eu point source depth using HPGe detector and MCNP simulation. The effects of measurement distance of PTV and PTC methods were evaluated. Using the results, the source depth assessment equation using the PTC and PTV methods was derived based on the detection distance of 50 cm. In addition, the sensitivity of detection distance changes was assessed when using PTV and PTC methods, and error increased by 3 to 4 cm when detection distance decreased by 20 cm based on 50 cm. However, it was confirmed that if the detection distance was increased to 100 cm, the effects of detection distance were small. And PTV and PTC methods were compared with the two distance measurement method which evaluates the depth of source by the change of net peak counting rate according to the detection distance. As a result of source depth assessment, the PTV and PTC showed a maximum error of 1.87 cm and the two distance measurement method showed maximum error of 2.69 cm. The results of the experiment confirmed that the accuracy of the PTV and PTC methods was higher than two distance measurement. In addition, Sensitivity evaluation by horizontal position error of source has maximum error of less than 25.59 cm for the two distance measurement method. On the other hand, PTV and PTC method showed high accuracy with maximum error of less than 8.04 cm. In addition, the PTC method has lowest standard deviation for the same time measurement, which is expected to enable rapid measurement.

• Journal of Bio-Environment Control
• /
• v.32 no.3
• /
• pp.210-216
• /
• 2023

Conventionally, the seeds of Rehmannia glutinosa (Gaertn.) Libosch. ex Steud. have been directly sown at the field without using the plug seedling method. Plug seedlings have the advantage of promoting germination and convenient transplanting. However, there is little information about propagation of R. glutinosa using the plug seedling method. This study was conducted to investigate the optimal seed rhizome length, diameter, and sowing direction of R. glutinosa for establishing the plug seedling method. Seed rhizome length and diameter were separated by 1, 2, 3 cm and 0.3-0.5, 0.6-1.0, 1.1-1.5 cm, respectively. And seed rhizomes were sown in vertical and horizontal directions. The survival rate in 1 cm length of seed rhizomes was lower than in other treatments. The leaf length, leaf width, number of leaves, SPAD, leaf area, and fresh and dry weights of shoot and roots were the greatest in 3 cm length of seed rhizomes. As the seed rhizome diameter decreased, the growth characteristics of R. glutinosa tended to increase. When R. glutinosa was sown horizontal direction, the leaf length, leaf width, number of leaves, and leaf area were significantly higher than in the vertical direction. In conclusion, when sowing seed rhizome in a plug tray, using a length of 3 cm, a diameter of less than 1 cm, and sowing in a horizontal direction is considered an appropriate sowing method for R. glutinosa.