• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.1-12
• /
• 2015

The current scenario of the transportation sector reflects the urgent need to address issues such as depletion of traditional fuel reserves and ever growing pollution levels. Researchers around the world are focussing on alternatives as well as optimisation of currently employed devices to reduce the pollution levels generated by the commonly used fuels. One such optimisation involves the study of air flow within the intake manifolds of SI engines. It is a well-known fact that alterations in the air manifolds of engines have a significant impact on the engine performance parameters, fuel consumption and emission levels. Previous works have demonstrated the impacts of runner lengths, diameter, plenum volume, taper angle of distribution manifolds and other factors on in-cylinder fluid motion and engine performance. However, a static setup provides an optimal configuration only at a specific engine speed. This paper aims to investigate the variations in the same parameters on a four stroke, naturally aspirated single cylinder SI engine through varying the cross section design over the intake runner with the aid of Computational Fluid Dynamics. The system consists of segments that form the intake runner with projections on the inside that allow various permutations of the intake runner segments. The various configurations provide the optimised fluid flow characteristics within the intake manifold at specific engine speed intervals. The variations such as turbulence, air fuel mixing are analysed using the three dimensional CFD software FLUENT. The results can be used further for developing an automated or manually adjustable intake manifold.

• 대한조선학회논문집
• /
• 제48권2호
• /
• pp.99-106
• /
• 2011

The appearance of CSR changes the concept of the hull form design as well as structural design, since the application of CSR inevitably brings the lightweight increase of a ship. Keeping the original design constraints such as principal particulars, deadweight, and speed performance, designers have to increase the volume of the hull form. As a result, the entrance angle at bow end should become larger, which results in blunter waterline shape. For a slow and full ship having high $C_B$ more than 0.85, a new concept of bow shape has been required to alleviate the increase of wave-making resistance, since it is very difficult to improve waterline and frameline shape for such a full ship. In this paper a new bow shape of Capesize Bulk Carrier was developed to improve its wave-making characteristics without incompliance with the design constraints. For loading manual calculation, NAPA software was used. FLUENT6.3.26 and WAVIS1.4 were used to evaluate resistance performance of the subject hull forms. The newly designed hull form was tested at SSPA model basin for the final confirmation of resistance and propulsion performance of the ship. It was found that the new bow shape of a Capesize Bulk Carrier improved the resistance characteristics greatly compared to a conventional bulbous bow. The other benefits of new bow shape on the manufacturability were also investigated.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.152-158
• /
• 2013

The purpose of this study is to investigate cooling performance of high power LEDs from 100 to 200 W class by using a jet impingement cooling module. The numerical analysis of forced convection cooling inside cooling module is carried out using a multi-purpose CFD software, FLUENT 6.3. In the experiments, the LED cooling system consists of jet impingement module, heat exchanger, water reservoir, and pump. In the present study, the cooling performance of jet impingement cooling module is investigated to determine the effect of the heat sink types on the impinging surface, the space and length of fins. Numerical and experimental studies show the reasonable agreement of LED metal PCB temperature between those results and give the optimized design parameters such as the space of fin and the length of fin. Also, the pin fin type of heat sink is found to be more efficient than the plate type heat sink in jet impingement cooling.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.286-291
• /
• 2008

Insulation of refrigerator with gasket material near door becomes the technical point at the aspect of heat loss and energy efficiency. Heat loss of refrigerator through the gasket is nearly 30%. In this paper, quantitative evaluation method of heat loss through gasket in established suggest the method for the improvement of heat loss. To analyze the heat transfer, we have used the common software Fluent that is used to CFD. Because of using the convection coefficient of heat transfer, we have solved only the equation of energy for heat transfer. As a result, we have known that heat loss flows through the heat flux vector and that the heat gathered out of the outside iron plate is transferred inner part through the gasket and ABS, etc. Through the result of the numerical simulation that use sub-gasket, we have known that we are able to reduce the heat loss about $20{\sim}40%$. when we applied that sub-gasket on a real refrigerator, the power consumption had reduced about 4.76%. In addition, when we applied a more improved sub-gasket on a real refrigerator and measured the power of the refrigerator the power consumption does reduce about 3% and we will try to apply the improved sub-gasket on a new models of refrigerator.

• 대한조선학회논문집
• /
• 제56권6호
• /
• pp.507-514
• /
• 2019

Computational studies of accelerating flow around 2D Circular Cylinder was performed to investigate characteristics of wake field and drag forces. Previous studies had revealed that drag on the cylindrical body in accelerating flow is much greater than that in the flow with constant velocity; however, the underlying physics on the drag increase has not been clearly investigated. In order to investigate the drag increase and its relationship with wake development, this study employed a finite-volume based CFD code, Fluent 13.0 with k-ω SST model for turbulence effects. Inflows are modeled with varied accelerations from 0.4905 to 9.81m/s². The drag computed in the present study is in good agreement with previous studies, and clearly shows the increase compared to the drag on the body in the flow with constant velocity. The results also show that drag crisis observed at high Reynolds number in the case of the flow with constant velocity is also found in the case of accelerating flow. The analysis for wake and recirculation length shows that conventional vortex shedding does not occur even at high Reynolds number and the drag increase is larger at higher acceleration.

• 한국태양에너지학회 논문집
• /
• 제29권1호
• /
• pp.44-49
• /
• 2009

Steam reforming of methane in the high temperature solar chemical reactor bas advantage in its heating method. Using concentrated solar energy as a heating source of the reforming reaction can reduce the $CO_2$ emission by 20% compared to hydrocarbon fuel. In this paper, the simulation result of methane-steam reforming on a high temperature solar chemical reactor(SCR) using Fluent 6.3.26 is presented. The high temperature SCR is designed for the Inha Dish-1, a Dish type solar concentrator installed in Songdo city. Basic SCR performance factors are referred to the former researches of the same laboratory. Inside the SCR porous metal is used for a receiver/reactor. The porous metal is carved like a dome shape on the incident side to increase the heat transfer. Also, ring-disc set of baffle is inserted in the porous metal region to increase the path length. Numerical and physical models are also used from the former researches. Methane and steam is mixed with the same mole fraction and injected into the SCR. The simulation is performed for a various inlet mass flow rate of the methane-steam mixture gas. The result shows that the average reactor temperature and the conversion rate change appreciably by the inlet mass flow rate of 0.0005 kg/s.

• 한국항해항만학회지
• /
• 제31권10호
• /
• pp.845-852
• /
• 2007

OWE형 파력발전장치는 해수면의 승강운동을 공기실 내의 공기 흐름으로 전환하고 이를 터빈의 구동력으로 사용하는 발전장치이다. 파랑에너지가, 터빈으로 유입되는 공기에너지로 전환하도록 하는 공기실의 내부 수위의 주기적 변동은 상하대칭이 이루어지지 않고, 공기실 내 공기 유동의 압축과 팽창 과정에서 유량차가 발생하게 된다. 본 논문에서는 이를 이용하여 보다 많은 유량을 임펄스터빈의 압력면으로 유도하여 날개의 압력면과 흡입면의 압력차를 크게 하는 Staggered Blade의 적용에 대해 검토하고 그에 대한 성능 해석을 수행하였다. 터빈의 압력면으로의 공기 흐름을 제어하기 위해 Self-Pitched Blade(가변 피치 날개)를 제안하였고, 이러한 유량차를 토대로 동 조건에서 최대의 발전량과 최고 효율의 터빈을 설계하고자 하는데 그 목적이 있다.

• Journal of Ship and Ocean Technology
• /
• 제10권4호
• /
• pp.12-23
• /
• 2006

In this paper, a numerical study is carried out to investigate the turbulent flow around a twin-skeg container ship model with rudders including propeller effects. A commercial CFD code, FLUENT is used with body forces distributed on the propeller disk to simulate the ship stem and wake flows with the propeller in operation. A multi-block, matching, structured grid system has been generated for the container ship hull with twin-skegs in consideration of rudders and body-force propeller disks. The RANS equations for incompressible fluid flows are solved numerically by using a finite volume method. For the turbulence closure, a Reynolds stress model is used in conjunction with a wall function. Computations are carried out for the bare hull as well as the hull with appendages of a twin-skeg container ship model. For the bare hull, the computational results are compared with experimental data and show generally a good agreement. For the hull with appendages, the changes of the stem flow by the rudders and the propellers have been analyzed based on the computed result since there is no experimental data available for comparison. It is found the flow incoming to the rudders has an angle of attack due to the influence of the skegs and thereby the hull surface pressure and the limiting streamlines are changed slightly by the rudders. The axial velocity of the propeller disk is found to be accelerated overall by about 35% due to the propeller operation with the rudders. The area and the magnitude of low pressure on the hull surface enlarge with the flow acceleration caused by the propeller. The propellers are found to have an effect on up to the position where the skeg begins. The propeller slipstream is disturbed strongly by the rudders and the flow is accelerated further and the transverse velocity vectors are weakened due to the flow rectifying effect of the rudder.

• 한국철도학회논문집
• /
• 제16권3호
• /
• pp.169-174
• /
• 2013

고성능 EMU 열차의 형상 개선을 통한 공기저항 저감 효과를 알아보기 위하여 3차원정상 Navier-Stokes 방정식과 2방정식 난류 모델을 이용한 전산유체역학을 이용하여 수치해석을 수행하였다. 전산시뮬레이션에는 FLUENTTM ver.13과 Gambit 2.4.6이 사용되었으며, 기본 형상과 유선형으로 개선된 형상에 대하여 계산을 수행하였다. 또한, 터널 내 주행 시의 공기저항 특성을 살펴보기 위하여 개활지에서의 공기저항 계산도 수행하였으며, 차량 별 공기저항 기여도에 대한 분석도 수행되었다. 유선형으로 개선된 형상의 열차는 절편형 전두부와 돌출된 상부 및 하부구조를 가진 기본 형상 열차에 비하여 약 9.8%의 공기저항이 저감된 것을 확인하였으며, 공기저항 저감에 따른 주행저항의 저감은 시속 80km/h에서 약 4%에 이르는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.247-253
• /
• 2018

Temperature rise due to viscous shear of the lubricating oil generates hydrodynamic pressure, even if the lubricating surfaces are parallel. This effect, known as the thermal wedge effect, varies significantly with film-temperature boundary conditions. The bearing conducts a part of the heat generated; hence, the oil temperature varies with the thermal conductivity of the bearing. In this study, we analyze the effect of thermal conductivity on the thermohydrodynamic (THD) lubrication of parallel slider bearings. We numerically analyze the continuity equation, Navier-Stokes equation, energy equation including the temperature-viscosity and temperature-density relations for lubricants, and the heat conduction equation for bearing by creating a 2D model of the micro-bearing using the commercial computational fluid dynamics (CFD) code FLUENT. We then compare the variation in temperature, viscosity, and pressure distributions with the thermal conductivity. The results demonstrate that the thermal conductivity has a significant influence on THD lubrication characteristics of parallel slider bearings. The lower the thermal conductivity, the greater the pressure generation due to the thermal wedge effect resulting in a higher load-carrying capacity and smaller frictional force. The present results can function as the basic data for optimum bearing design; however, the applicability requires further studies on various operating conditions.