• Journal of the KSME
• /
• v.50 no.8
• /
• pp.51-53
• /
• 2010

이 글에서는 항공우주왕복선의 엔진설계 시 사용되었던 CFD(Computational Fluid Dynamics) 기술을 인공심장 개발에 어떻게 적용하여 심장보조장치(Ventricular Assist Device)를 만들었는지 소개하고자 한다.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.65-70
• /
• 2024

Using a computational fluid dynamics(CFD) simulation tool, we have provided a coating guideline for slot-die coating with a double layer slot die head. We have analyzed the fluid dynamics in terms of the coating speed, flow rate ratio, and viscosity ratio, which are critical for the stability of coating meniscus. We have identified the common coating defects such as break-up, air entrainment, and leakage by varying the coating speeds. The flow rate ratio is the critical parameter determining the wet film thickness of the top and bottom layers. It is shown that when the flow rate ratio exceeds or equals 1.8, air entrainment occurs due to insufficient hydraulic pressure in the bottom layer, even though the total flow rate remains constant. Furthermore, we have found that the flow of the bottom layer is significantly affected by the viscosity of top layer. The viscosity ratio of 4 or higher obstructs the flow of the bottom layer due to the increased hydraulic resistance, resulting in leakage. Finally, we have demonstrated that as the viscosity ratio increases from 0.1 to 10, the maximum coating speed rises from 0.4 mm/s to 1.6 mm/s, and the minimum wet film thickness decreases from 800 ㎛ to 200 ㎛.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.3
• /
• pp.285-294
• /
• 2015

As a "kind of" mature ship form, planing hull has been widely used in military and civilian areas. Therefore, a reasonable design for planing hull becomes more and more important. For planing hull, resistance and trim are always the most important problems we are concerned with. It affects the planing hull's economic efficiency and maneuverability very seriously. Instead of the expensive towing tank experiments, the development of computer comprehensive ability allows us to previously apply computational fluid dynamics(CFD)to the ship design. In this paper, the CFD method and Goal Driven Optimization (GDO) were used in the estimations of planing hull resistance and running attitude to provide a possible method for performance computation of planing hull.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.2
• /
• pp.155-162
• /
• 2015

Abalone (Haliotis discus hannai) is a shellfish that feeds on kelp and, as a product, it can often achieve a high market value. However, the dissolved oxygen (DO) levels in coastal waters in Korea have been negatively impacted by pollution from many anthropogenic sources. Herein, a computational fluid dynamics (CFD) software package was used to analyze the distribution of the DO concentration within an abalone containment structure. A finite volume approach was used to solve the Reynolds-averaged Navier-Stokes equations combined with a $k-{\varepsilon}$ turbulence model to describe the flow. The distribution of DO was determined within the control volume domain, and the transport equations of the pollutants were interpreted using a CFD model. The CFD analysis revealed that more than 60% and 30% of the relative oxygen concentration in one and two containers, respectively, was maintained when the flow acts along the six sheets of polyethylene plates. Therefore, it is clear that the abalone plate shelters should be placed parallel to the flow.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.1
• /
• pp.1-6
• /
• 2006

The objective of this study is CFD analysis of CPU cooler jacket. The ANSYS code using was for this CFD analysis. In order to analysis of CPU cooler jacket, many variables such as boundary condition, conductivity, mass density, specific heat were considered. This analysis results are compare to small inner size jacket and large inner size Jacket.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.446-455
• /
• 2017

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance ($C_R$) in the total resistance ($C_T$) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• Proceedings of the Korean Information Science Society Conference
• /
• 2007.10b
• /
• pp.463-467
• /
• 2007

CFD(Computational Fluid Dynamics)는 수치 기법(Numerical)과 알고리즘을 사용하여 유체 유동 문제를 풀고 해석하는 것이다. 본 논문에서는 이러한 CFD 분석 프로그램의 효율적인 수행을 위해 분산 환경을 기반으로 하는 메타컴퓨팅(Metacomputing) 시스템에 대해서 기술한다. 실제 CFD 프로그램을 단일 클러스터 시스템에서 수행시켰을 때와 메타컴퓨팅 시스템을 이용하여 수행시켰을 때 소요되는 시간과 결과 파일을 실험을 통하여 비교한다. 그 결과 메타컴퓨팅 시스템을 이용하여 CFD 분석 프로그램을 분산 수행시킨 경우는 그렇지 않은 경우에 소요되는 시간보다 평균 $15.3{\sim}38.5%$ 정도 빨랐고, 동일한 결과를 얻을 수 있음을 확인하였다.

• Aerospace Engineering and Technology
• /
• v.3 no.1
• /
• pp.35-44
• /
• 2004

In this study, one dimensional aerodynamic and structural study of a partial admission turbo pump turbine was performed. A turbine consists of a nozzle, rotor, outlet guide vanes. The aerodynamic characteristics of each component was derived from the governing equation and validated from the CFD calculations. One-dimensional basic design such as velocity triangles was conducted from the mean line analysis and modified from the 2-D and 3-D CFD analysis. The blade profile was determined by the CFD optimization. The thermal stress analysis and structural analysis are needed to be studied in the next design stage.

• Journal of Wind Energy
• /
• v.4 no.1
• /
• pp.68-74
• /
• 2013

Offshore wind farm is being increased since there are much trouble to develop onshore wind farm. But in the offshore, wind turbine wake does not dissipate less than onshore wind turbine because of low turbulence level. Thus this remained wake interacted to other wind turbine. This interaction reduces energy production in wind farm and have a bad influence on fatigue load of wind turbine. In this research, CFD model was constructed to analyze wake effect in offshore wind farm. A method that wind turbine rotor region was modelled in porous media was devised to reduce computation load and validated by comparison with Horns Rev measurement. Then wake interaction between two wind turbine was analyzed by devised porous model.