• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• Korean Journal of Microbiology
• /
• v.52 no.3
• /
• pp.344-351
• /
• 2016

A marine bacterium, designated as strain 50C-3, was isolated from a seawater sample collected from the East Sea of South Korea. The strain is a Gram-negative, aerobic, yellow colored polar-flagellated bacterium that grows at $20-50^{\circ}C$ and pH 5.5-8.5. Optimal growth occurred at $40-50^{\circ}C$, at pH 6.5-7.5, and in the presence of 2% (w/v) NaCl. Based on 16S rRNA gene sequence similarity, the isolate was considered to represent a member of the genus Ruegeria. The result of this analysis showed that strain 50C-3 shared 99.4% and 96.98% sequence similarity with Ruegeria intermedia CC-GIMAT-$2^T$ and Ruegeria lacuscaerulensis ITI-$1157^T$, respectively. Furthermore, strain 50C-3 showed clear differences from related strains in terms of several characteristics such as motility, carbon utilization, enzyme production, etc. The DNA G+C content was 66.7 mol%. Chemotaxonomic analysis indicated ubiquinone-10 (Q-10) as the predominant respiratory quinone. Based on phenotypic, chemotaxonomic, and phylogenetic characteristics, the isolate represents a novel variant of the Ruegeria intermedia CC-GIMAT-$2^T$, for which we named Ruegeria sp. 50C-3 (KCTC23890=DSM25519). Strain 50C-3 did not produce cellulase and agarase, but produced alkaline phosphatase, ${\alpha}$-galactosidase, and ${\beta}$-galactosidase. The three enzymes showed stable activities even at $50^{\circ}C$ and thus regarded as thermostable enzymes. Especially, the ${\beta}$-galactosidase activity enhanced by 1.9 times at $50^{\circ}C$ than that at $37^{\circ}C$, which may be very useful for industrial application.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2002.11a
• /
• pp.131-186
• /
• 2002

우리나라 유통상토에 대한 물리적 표준분석법을 설정하기 위한 연구를 실시하였다. 국내 시중에 유통되고 있는 53개 품목의 원예용 상토와 9개 품목의 수도용 상토를 대상으로 설정된 분석법을 적용하여 실험하였다. 입자밀도의 측정은 가스형 피크노메타(Micromeritics Co. Model 1305)를 사용하면 속도와 정확성 면에서 매우 유리하였다. 용적밀도는 구미에서 Sandbox법에 의한 용적밀도를 기본으로 하기 때문에 이와 유사한 성적을 얻을 수 있는 다양한 실험을 한 결과, 추다짐법(Plunger compaction method)이 가장 유의성 있는 측정 방법으로 밝혀졌다. 한편 가스형 피크노메타법에 의한 우리나라 유통상토의 입자밀도는 원예용이 1.93, 수도용이 2.43 Mg m$^{-3}$로 나타났으며, 추다짐법에 의한 용적밀도는 원예용이 0.22, 수도용이 1.01 Mg m$^{-3}$로 각각 나타났다. 수분함량은 105$^{\circ}C$ 건조기에서 16시간 건조하여 수도용상토는 (최초 무게-건조 후 무게) / (건조 후 무게) $\times$ 100으로, 원예용상토는 (최초무게 - 건조 후 무게) / (최초 무게) $\times$ 100으로 하였다. 보수력은 주로 저압용으로서 Eijkelkamp사의 Sandbox법을 사용하여 0.5, 1, 3, 5, 7, 10 ㎪의 수분장력 상태의 수분함량을 조사하였다. 포화수리전도도는 직경 5cm$\times$높이 20cm인 아크릴 원통을 이용하여 정수위별에 의한 포화수리전도도를 측정하였다. 신분석법에 의한 유통상토의 수분함량은 원예용이 평균 46.34%, 수도용이 평균 16.89%이었고 원예용 상토의 EAW는 28.4%, WBC 7.01%, OMP는 5.60 ㎪로 나타났으며, 육묘를 위한 적정 수분함량은 44.41%이었고 포화수리전도도는 1.71 cm $min^{-1}$이었다. 상토 평량시 무게를 비교한 결과 상토 부피를 달리하여도 고도의 유의성이 있었고, 상토 20cc의 평균무게는 4.92g(2.08-8.83g)이었다. 상토의 EC 측정시 상토:물의 비율이 1:2(v:v)와 1:5(v:v)분석치에 2.5배한 EC 값과는 고도의 정의 상관관계가 있었으며, 유럽법과 일본법(전농)과의 관계는 고도의 정의 상관관계가 있었다 또한 새로운 분석법(v:v 1:5)으로 측정한 EC의 평균값은 국내산 0.64, 수입산 0.33 dS m$^{-1}$이 었다. 상토의 pH 측정시 상토:물의 비율을 1:2(v:v)와 1:5(v:v)와의 관계에서는 정의 상관관계를 보였으며, 유럽법과 일본법(전농)과의 관계도 역시 고도의 정의 상관관계가 있었고, 신 분석법에(v:v 1:5) 의한 분포비율은 국내산, 수입산모두 pH 6.1-6.5의 범위에서 가장 높았다.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.2
• /
• pp.77-88
• /
• 2005

This paper introduces a project for the development of an F-125 machine using 3D PLM systems including 3D CAD, CAM, CAE, PDM, and DMU systems. Here, the F-125 machine is a formula racing car equipped with a 125cc motorcycle engine. A development process and computer-integrated environment was established using 3D PLM systems on the conceptual basis of concurrent and virtual engineering. A DMU model for a full vehicle was built using CATIA V.5 and used to check interference between parts and to simulate assembly process. This DMU-based approach enables to find and fix manufacturing problems in the early design stage. All development activities have been done by the graduate and undergraduate students of the automotive engineering department of Kookmin University. Through the project, the students could acquire knowledge about car development process and 3D PLM systems in automotive industry.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.5
• /
• pp.367-371
• /
• 1986

Dynamic and equilibrium properties of n-alkane chains immersed in solvent molecules have been investigated by a molecular dynamics method. The n-alkane chain is assumed to be a chain of elements (CH$_2$) interconnected by bonds having a fixed bond length and bond angle, but each bond of the chain is allowed to execute hindered internal rotation. We studied the effect of the number of the chain elements (N$_c$ = 10, 15 and 20) on the equilibrium properties of the system, e.g., the pair correlation functions between a chain element and solvent molecules, g$_{cs}$(r), and between the chain elements, g$_{cc}$(r), and the configurational properties such as the mean-square end-to-end distance < R$^2$ >, the mean-square radius of gyration < S$^2$ >, and the eigenvalues of the moment-of-inertia tensor < S$_i^2$ > / < S$^2$ > (i = 1, 2 and 3). We also studied the dynamic properties of the system, e.g., the autocorrelation function C(A;t) where A = R$^2$(t), = S$^2$(t), or = ${\vec{V}}(t)({\vec{V}}$ = velocity of the center of mass), and the diffusion coefficient D. The g$_{cs}$(r)'s are almost equal irrespective of the change of Nc while g$_{cc}$(r) becomes larger as N$_c$ increases; The MD computed configurational properties < R$^2$2 > and < S$^2$ > were found to be a little different from the values calculated from the statistical equations of < R$^2$ > and < S$^2$ >, it may be due to the fact that our model for the MD simulations includes a long-range volume effect. From the < S$_i^2$ > / < S$^2$ >, it is found that the chain molecule has a nearly spherical shape irrespective of the variation of N$_c$. For the dynamic properties we found that the C(R$^2$;t) and C(S$^2$;t) of lower N$_c$ decay faster than those of higher N$_c$, while the C($\vec V$;t) of the center of mass in the chain is weakly dependent on the N$_c$. The center of mass diffusion coefficient D$_c$ decreases as N$_c$ increases while the end point diffusion coefficient D$_e$ is nearly equal irrespective of the change of N$_c$.

• Structural Engineering and Mechanics
• /
• v.70 no.1
• /
• pp.13-31
• /
• 2019

A nonlinear finite element model (FEM) using ATENA-3D software to simulate the axially compressive behavior of circular steel tube confined concrete (CSTCC) columns infilled with ultra high performance concrete (UHPC) was presented in this paper. Some modifications to the material type "CC3DNonlinCementitious2User" of UHPC without and with the incorporation of steel fibers (UHPFRC) in compression and tension were adopted in FEM. The predictions of utimate strength and axial load versus axial strain curves obtained from FEM were in a good agreement with the test results of eighteen tested columns. Based on the results of FEM, the load distribution on the steel tube and the concrete core was derived for each modeled column. Furthermore, the effect of bonding between the steel tube and the concrete core was clarified by the change of friction coefficient in the material type "CC3DInterface" in FEM. The numerical results revealed that the increase in the friction coefficient leads to a greater contribution from the steel tube, a decrease in the ultimate load and an increase in the magnitude of the loss of load capacity. By comparing the results of FEM with experimental results, the appropriate friction coefficient between the steel tube and the concrete core was defined as 0.3 to 0.6. In addition to the numerical evaluation, eighteen analytical models for confined concrete in the literature were used to predict the peak confined strength to assess their suitability. To cope with CSTCC stub and intermediate columns, the equations for estimating the lateral confining stress and the equations for considering the slenderness in the selected models were proposed. It was found that all selected models except for EC2 (2004) gave a very good prediction. Among them, the model of Bing et al. (2001) was the best predictor.

• Radiation Oncology Journal
• /
• v.27 no.4
• /
• pp.194-200
• /
• 2009

Purpose: This aim of this study was to evaluate changes in gastric volume and organ position as a result of delayed gastric emptying after a subtotal gastrectomy performed as part of the treatment of stomach cancer. Materials and Methods: The medical records of 32 patients who underwent concurrent chemoradiotherapy after a subtotal gastrectomy from March 2005 to December 2008 were reviewed. Of these, 5 patients that had more than 50 cc of residual gastric food detected at computed tomography (CT) simulation, were retrospectively enrolled in this study. Gastric volume and organ location was measured from CT images obtained before radiotherapy, twice weekly. In addition, authors evaluated the change of radiation dose distribution to planning the target volume and normal organ in a constant radiation therapy plan regardless of gastric volume variation. Results: A variation in the gastric volume was observed during the radiotherapy period (64.2~340.8 cc; mean, 188.2 cc). According to the change in gastric volume, the location of the left kidney was shifted up to 0.7 - 2.2 cm (mean, 1.2 cm) in the z-axis. Under-dose to planning target volume (V43, 79.5${\pm}$10.4%) and over-dose to left kidney (V20, 34.1${\pm}$12.1%; Mean dose, 23.5${\pm}$8.3 Gy) was expected, given that gastric volume change due to delayed gastric emptying wasn't taken into account. Conclusion: This study has shown that a great change in gastric volume and left kidney location may occur during the radiation therapy period following a subtotal gastrectomy, as a result of delayed gastric emptying. Detection of patients who experienced delayed gastric emptying and the application of gastric volume variation to radiation therapy planning will be very important.

• Journal of Fashion Business
• /
• v.8 no.4
• /
• pp.117-130
• /
• 2004

The purposes of this study were to find out highly market sharing young casual brands, to compare their trends of concept and competition, and to propose orientation of brand concept repositioning and marketing strategies on Department stores. Reference searching method and field searching method were used for this study. The results were as follows: 1. The brands which covered more than 50% market share included <96NY> . 2. Price range of these brands was from 130,000 to 220,000 won. The brands of upper-moderate price zone included <96NY> and they were very competitive each other. The brands of moderate price zone included and they were also very competitive between them. However, the brands of lower-moderate price zone had lower competition. This price zone might be a good point to launch new brands. 3. The main target-age of young casual zone was from 17 to 30 years. The most of brands focused on 21-25 years old, which were higher age targeted before. 4. The main concepts of these brands were 'luxury, girlish, sexy' and 'Sportism, lifestyle' were sub-concepts.

• Journal of the Mineralogical Society of Korea
• /
• v.8 no.1
• /
• pp.23-28
• /
• 1995

그레자이트가 한국에서는 최초로 남동 황해 대륙붕의 준표층 니질퇴적물에서 발견되었다. 이 지역의 수심은 70~80m이며, 표층 퇴적물은 수십cm 두께의 사질과 니질퇴적물이 교호하는 것으로 보아 조류의 영향을 받은 홀로세의 해침에 의하여 형성된 것으로 보인다. 그레자이트 입자는 0.1~2mm의 크기에 구상의 형태로 산출되며 니질퇴적물 내에 산점상으로 산포되어 있거나 0.5cm 정도의 엽리를 형성하고 있다. 이 광물은 강한 자성을 가지고 있으며 육안으로는 검은색을 띄나, 반사현미경하에서는 황백색을 띠며 등방성을 보인다. 그레자이트의 화학조성은 Fe=54.36, S=42.37, As=0.14, Si=2.25 wt.%로서 S=4일 때의 화학식은 Fe2.95S4이다. X-선 회절분석에 의한 단위포의 크기는=9.8635$\AA$, V=959.6$\AA$3이며 밀도는 4.094 gm/cc이다. 이 광물은 산출상태, 조직적 특징 및 수반광물의 종류로 보아 생물의 활동에 의한 환원조건의 니질퇴적물 내에서 자생한 것으로 추정된다.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.594-599
• /
• 2008

This paper presents a micro air pump based on the synthetic jet to supply reactant at the cathode side for micro fuel cells. The synthetic jet is a zero mass flux device that converts electrical energy into the momentum. The synthetic jet actuation is usually generated by a traditional PZT-driven actuator, which consists of a small cylindrical cavity, orifices and PZT diaphragms. Therefore, it is very important that the design parameters are optimized because of the simple configuration. To design the synthetic jet micro air pump, a numerical analysis has been conducted for flow characteristics with respect to various geometries. From results of numerical analysis, the micro air pump has been fabricated by the PDMS replication process. The most important design factors of the micro air pump in micro fuel cells are the small size and low power consumption. To satisfy the design targets, we used SP4423 micro chip that is high voltage output DC-AC converter to control the PZT. The SP4423 micro chips can operate from $2.2{\sim}6V$ power supply(or battery) and is capable of supplying up to 200V signals. So it is possible to make small size controller and low power consumption under 0.1W. The size of micro air pump was $16{\times}13{\times}3mm^3$ and the performance test was conducted. With a voltage of 3V at 800Hz, the air pump's flow rate was 2.4cc/min and its power consumption was only 0.15W.