• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.5
• /
• pp.469-476
• /
• 2009

Hard facing overlay welding in high chromium carbide is a representative way of extending the fatigue life or recompensing damage, because workpiece surface is uniformly overlay-welded by alloy material. In general, grinding process is currently used for finish due to hardness of weld material. The development of tool material, such as PCBN, has made it possible to use turning instead of grinding. There are many advantages of hard Owning, as lower equipment costs, shorter setup time, fewer process steps, higher material removal rate, better surface integrity and the elimination of cutting fluid. In this paper, machining characteristics and cutting performance are examined to investigate turning possibility of overly welding in high chromium carbide.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.315-318
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining characteristics of milling by CBN tip was exprimentely analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The selection of a heating method for obtaining ideal temperature of metals in machining is important. Faulty heating methods could induce unwanted structural changes in the workpiece and increase the cost. This study uses gas flame heating. It is obtained that tungsten carbide-alloyed has a recrystallisation temperature range of $800-1000^{\circ}C$ which is the high heating temperature that might induce unwanted structural changes. If it is performed at temperatures higher than $800^{\circ}C$ in machining, the possibility of unwanted structural changes and the increased wear of tool can be shown. Consequently, in hot machining of tungsten carbide-alloy, this study has chosen $400^{\circ}C-600^{\circ}C$ because the heating temperature might be appropriate in view of the cost and workpiece considerations. The results of this study experimentally shows a new machining method for tungsten carbide-alloyed that decreases the wear rate of machining tools

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.35-39
• /
• 2010

Generally, ceramic material is very difficult to machine due to high strength and hardness. However, ceramic material can be machined at high temperature by plastic flow as metallic material due to the deterioration of the grain boundary glassy phase. Recently, a new method was developed to execute cutting process with CBN cutting tool by local heating of surface with laser. There are various parameters in LAM because it is a complex process with laser treatment and machining. During laser assisted machining, high power results in reducing of cutting force and increasing tool life, but excessive power brings oxidation of the surface. The effect of laser power, feed rate, cutting depth and etc. were investigated on the life of cutting tool. Chips were observed to find out suitable machining conditions. Chips of SSN had more flow-types than HIPSN. It means SSN is easier to machining. The life of cutting tool was increased with increasing laser power and decreasing feed rate and cutting depth.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.138-143
• /
• 2000

The establishment of a practical ultra-precision grinding technique using Diamond and CBN wheels is one of the major key technolo-gies to improve production techniques for machine-to-difficult materials without finishing process such as lapping and polishing. But the special efficient dressing technique for ultra-fine grit type grinding wheels to stabilize the grinding ability was not developed. Recently electrolytic in-process dressing technique is proposed to ultra-fine grit type metal bonded diamond wheels to protrude abra-sives continuously from the tool surface. This technology can be widely used to surface grinding and cylindrical grinding but cannot be used efficiently to internal grinding because of the electrode attachment trouble. This paper describes the effect of interval type electrolytic dressing as proposed newly to cast iron bonded diamond wheel for efficient internal grinding with mirror type high quality ground surface.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.2
• /
• pp.30-36
• /
• 2007

In order to estimate the maximum undeformed chip thickness in grinding operation, it is necessary to obtain the successive cutting point spacing. In the past it was obtained by experiments. In this paper, the average successive cutting point spacing has been obtained using the given grinding input conditions and it is possible to estimate the maximum undeformed chip thickness without using any experimentally obtained data. The validity of the proposed analysis has been verified based on two sets of grinding scratch tests using WA and CBN grinding wheels.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.59-64
• /
• 1998

We need to achieve th mass product through methods of higher efficient, higher precise manufacturing process than those of existing precision abrasive machining. Thus, this study is to develop mirror-like surface machining technique of outer diameter of the piston pin by the compound magneto-electrolytic abrasive polishing system. The procedure of machining is followed as first, fulfill the pre-processing by cylindrical grinder, second, complete mirror-like surface by the method of magneto-electrolytic abrasive polishing used CBN non-woven abrasive pads. In this study, it was found that the best suitable conditions of mirror-like surface polishing were that the electrode density was 0.1A/$\textrm{cm}^2$, the applied pressure 1.5kgf/$\textrm{cm}^2$, the feed rate 0.5mm/rev, and the rotoation velocity of workpiece 80rpm, and that the surface roughness was reduced in this conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2279-2286
• /
• 1992

A hypereutectic Aluminum-Silicon Alloy is widely used in the parts of autombile because of high-resistance and good strength. In this study, the cutting of a hypereutectic Al-Si alloy (A390) for extraction of Si particle was experimentally investigated. By proper selection of cutting tool materials and optimization of cutting conditions, economical machining of this alloy is achieved. The surface roughness relates closely with the feed rate and cutting speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.190-196
• /
• 1993

Internal high speed grinding under several high grinding wheel speed condition has been performed in this study for the effects have analyzed and compared with the grinding power, grinding tangential force and accuracy of surface with the carbon tool steel(SK3). The following results have been obtained: (1) Under the workpiece speed constant condition, increasing the grinding speed, the tangential force is decreased, and on the contrary, accuracy of surface is improved. (2) Under the speed ratio (V$_{w}$/V$_{s}$) contant condition it is possible to increase the high machining efficiency constraint to tangential grinding force constant.ant.

• Steel and Composite Structures
• /
• v.34 no.5
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.61-66
• /
• 2010

Silicon nitride is widely used as an engineering ceramics because it has high strength, abrasion resistance and corrosion resistance even at high temperature. However, machining of silicon nitride is difficult due to its high hardness and brittleness. Laser assisted machining(LAM) allows effective cutting using CBN tool by locally heating the cutting part to the softening temperature of YSiAlON using the laser beam. The effect of preheating depending on process parameters were studied to find out the oxidation mechanism. If silicon nitride is sufficiently preheated, the surface is oxidized and $N_2$ gas is formed and escapes from the material, thereby making the cutting process more advantageous. During laser preheating process before machining, high temperature results in strong oxidation which makes the bloating, silicate layers and micro cracks. Using the results of these experiments, preheating characteristics and oxidation behavior were found out.