• 제목/요약/키워드: CAM Rotational Speed

검색결과 11건 처리시간 0.029초

직접 구동형 밸브 트레인 시스템의 태핏 회전에 관한 실험적 연구 (An Experimental Study on the Tappet Spin for a Direct Acting Valve Train System)

  • 조명래;김형준;문태선;한동철
    • 대한기계학회논문집A
    • /
    • 제27권7호
    • /
    • pp.1179-1184
    • /
    • 2003
  • The technique for measuring the rotational speed of tappet in direct acting type valve train system has been developed. The optic signal monitoring system with laser and optic fiber was designed to follow the signal of tappet rotation. The system was based on ON/OFF signal generation from the additional encoder teeth under the tappet with optic fibers attached photo transistor. The data showed that tappet rotation was affected by offset, oil temperature and cam shaft operating speed. Also it was found that tappet rotation increases with oil temperature. Tappet spin was delayed 10∼s20$^{\circ}$ cam angle after valve opening. The instantaneous rotational speed of tappet was reciprocal to cam shaft speed and the tappet and the cam angle ratio was located in the range of 0.1∼0.3.

밸브 트레인 시스템의 태핏 회전 측정 장치의 개발 (Development of Measurement System for Tappet Rotation in the Valve Train System)

  • 김형준;조명래;신흥주;한동철
    • Tribology and Lubricants
    • /
    • 제14권3호
    • /
    • pp.81-86
    • /
    • 1998
  • The purpose of this paper is to measure the rotational speed of tappet in OHC valve train system. Tappet has eccentricity about cam center, which induces the tappet rotation and prevents from wear. In this paper, the experimental test rig which composes of one cam system is developed to measure the tappet rotation by using the laser generating system, rotary encoder, optical fiber, and photo transistor. The direction of tappet rotation is judged from the oder of optical signal. As results of experiment, average and instant rotational speed and average rotation angle per one cam revolution are presented. Measured results show that eccentricity ratio is dominant factor for the tappet rotation, and tappet is rotated at the base circle.

직접 구동형 밸브트레인 시스템의 캠-팔로워 접촉면의 접촉 응력 해석 (The Analysis of the Contact Stresses at the Cam and Follower Interface in the Direct Acting Type Valve Train System)

  • 조명래;신흥주;한동철
    • Tribology and Lubricants
    • /
    • 제16권4호
    • /
    • pp.289-294
    • /
    • 2000
  • This paper present the contact stresses, which considers the shear stress at the cam and follower interface in the direct acting type valve train system of a high speed engine. To determine the contact condition, the normal contact forces are calculated by using the lumped mass dynamic modeling. The line contact is considered between the cam and follower interface. The variations of dynamic stresses are presented as a function of camshaft rotational angle. Also the effects of various design parameters are investigated.

A Study on the Characteristics of Volumetric Efficiency of an Axial Piston Pump considering Piston Tilting

  • Park, In-Kyu;Rhim, Yoon-Chul
    • KSTLE International Journal
    • /
    • 제10권1_2호
    • /
    • pp.37-42
    • /
    • 2009
  • This paper presents the characteristics of volumetric efficiency of an axial type piston pump considering the piston tilting. A numerical analysis is carried out in order to obtain the pressure distribution considering the fluid inertia at the notch of the valve plate. The cylinder pressure variation and the discharge flow rate are measured experimentally according to the operating conditions such as supply pressure, rotational speed, and viscosity of the working fluid by using the cam type test apparatus. Leakage is also measured considering piston tilting. The characteristics of the volumetric efficiency are analyzed with respect to various operating conditions and leakage is also analyzed according to the piston tilting angle. Results are applicable to improve the design of an axial type piston pump.

고성능 유압 베인펌프의 윤활특성 (Lubrication Characteristics of High Performance Oil Hydraulic Vane Pump)

  • 정재연
    • Tribology and Lubricants
    • /
    • 제9권1호
    • /
    • pp.45-54
    • /
    • 1993
  • The lubrication characteristics of line contacts between the vane and cam ring in an oil hydraulic vane pump with intravanes have been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic internal pressures in four chambers surrounding a vane, and variations of the film thickness were estimated in both the rotational speed range from 500 to 1500 rpm and in the delivery pressure range from 1 to 14 MPa. The results indicate the variations of the radial acting force and film thickness. It is found that the regimes of lubrication in the vane tip contacts lover rigid-isoviscous to rigidvariable viscosities.

핀 휠 기반 거스 기어의 접촉 피로수명 평가 (Estimation of Contact Fatigue Life of a Girth Gear Based on Pinwheel)

  • 권순만;신흥철
    • 한국생산제조학회지
    • /
    • 제25권4호
    • /
    • pp.245-252
    • /
    • 2016
  • Girth gears are applied in the mining, cement, and mineral processing industries and used in various types of horizontal mills, rotary dryers and kilns, and other heavy-gear ring applications. The large ring gears are normally fitted outside mills or kilns to provide the primary rotational drive. Recently, an external pinwheel gear set (e-PGS) was introduced to overcome manufacturing problems associated with girth gears. e-PGS is also suitable for low-speed, heavy-duty mechanical transmission and dusty and poor-lubrication conditions. This paper first presents a new profile modification of root relief for the e-PGS cam pinion. We then investigate load-stress factors to estimate the surface fatigue life by varying the shape design parameters. The results show that the contact fatigue life of an e-PGS can be extended significantly by increasing the profile shift coefficient. However, support bearing life of the pinwheel depends more on the contact force distribution than the profile shift coefficient.

디젤엔진용 고압분사 유닛인젝터의 성능예측을 위한 사이클 시뮬레이션 (Cycle Simulation for the Performance Prediction of a High Pressure Unit Injection System of a Diesel Engine)

  • 김철호
    • 한국자동차공학회논문집
    • /
    • 제9권1호
    • /
    • pp.63-74
    • /
    • 2001
  • In this study, a cycle simulation program of a Unit-Injection(UI) system was developed to estimate the injection performance of newly designed injection system. A fundamental theory of the simulation program is based on the conservation law of mass. Loss of fuel mass in the system due to leakage, compressibility effect of the liquid fuel and friction loss in the control volume was considered in the algorithm f the program. For the evaluation of the simulation program developed, the experimental result which was offered by the Technical Research Center of Doowon Precision Industry Co. was incorporated. Two main parameters; the maximum pressure in the plunger chamber and total fuel mass(kg) injected into the engine cylinder per cycle, were measured and compared with the simulation results. It was found that the maximum error rate of the simulation result to the experimental output was less than 3% in the rated rotational speed (rpm) range of the plunger cam.

  • PDF

유압 베인 펌프의 압력 맥동에 관한 연구 (The Analytical Study on the Pressure Ripples in a Positive Displacement Vane Pump)

  • 김기동;조명래;한동철;최상현
    • 한국윤활학회:학술대회논문집
    • /
    • 한국윤활학회 1997년도 제26회 추계학술대회
    • /
    • pp.225-231
    • /
    • 1997
  • This paper reports on the theoretical study of the delivery pressure ripples of a positive displacement vane pump which is widely used for automobile power steering. Pressure ripples occur due to the flow tipples which induced cam ring profiles and reverse flow from the delivery ports. In this paper, the mathematical model for analyzing the pressure ripples has been presented, and set of the differential equationshave been solved using the Runge-Kutta method. As the results of analysis, instant ideal flow ripples, internal pressure, delivery pressure ripples, and delivery flow ripples have been presented. Internal pressure was related to delivery pressure variations, and amplitude of pressure tipples was increased with rotational speed and delivery pressure.

  • PDF

유한요소해석을 이용한 선박수송차량용 사이클로이드 감속기의 성능 검토 (Performance Review of a Cycloid Speed Reducer for Ship Transport Vehicles using FEM)

  • 강형선
    • 한국산학기술학회논문지
    • /
    • 제12권5호
    • /
    • pp.2061-2066
    • /
    • 2011
  • 사이클로이드 감속기는 기계의 회전수를 조절하기위한 장치이다. 사이클로이드 감속기는 큰 토크로 변환시킬 수 있는 장점이 있지만 높은 회전수 에는 적합하지 않다. 한편 200톤 하중이 가해지는 수송기기에 있어서 감속기의 사용한계속도를 찾아내기는 불가능하다. 본 연구에서는 LS-DYNA를 이용하여 마찰손실동력을 수치 해석적으로 검토하였다. 최대토크3.5ton-m에 있어서 회전수 60rpm 그리고 162rpm으로 구동하여 해석을 수행한 결과 다음과 같은 결과를 얻었다. 60rpm회전의 경우 최대응력은 RV gear의 경우 463MPa 핀기어의 경우 507MPa이 발생하였다. 마찰손실동력은 50kW이며, 162rpm의 경우 최대응력값은 RV gear와 핀기어 각각 550MPa, 538MPa이 발생하였다. 손실동력은 175kW이 발생하여 사용이 불가능하다는 것을 알 수 있었다.

An Analytical Study on the Performance Analysis of a Unit-In-jector System of a Diesel Engine

  • Kim, Chul-Ho;Lee, Jong-Soo
    • Journal of Mechanical Science and Technology
    • /
    • 제17권1호
    • /
    • pp.146-156
    • /
    • 2003
  • A numerical algorithm is developed to analyze the performance of a Unit-injector (UI) System for a diesel engine. The fundamental theory of the algorithm is based on the continuity equation of fluid dynamics. The loss factors that should be seriously regarded on the continuity equation are the compressibility effect of liquid fuel, the wall friction loss in high-pressure fuel lines of the system, the kinetic energy loss of fuel in the system, and the leakage of fuel out of the control volume. For an evaluation of the developed simulation algorithm, the calculation results are compared with the experimental outputs provided by the Technical Research Center of Doowon Precision Industry Co. (DPICO) ; the maximum pressure in the plunger chamber (P$\_$p/) and total amount of fuel injected into a cylinder per cycle (Q$\_$f/) at each operational condition. The result shows that the average error rate (%) of P$\_$p/ and Q$\_$f/ are 2.90% and 4.87%, respectively, in the specified operational conditions. Hence, it can be concluded that the analytical simulation algorithm developed in this study can be reasonably applied to the performance prediction of newly designed UI system.