• 한국전기전자재료학회논문지
• /
• 제23권11호
• /
• pp.859-863
• /
• 2010

Evolution of surface morphology of ${\alpha}-Al_2O_3$ substrate was investigated as a function of annealing temperature and time. Commercial (0001) ${\alpha}-Al_2O_3$ single crystal substrates were annealed in the range of $600-1000^{\circ}C$ in air. At $600^{\circ}C$, step-terrace structure started to be formed on the substrate. However, the surface roughness on the terrace was still considerable and a number of islands were observed on the step edges as well as the terraces. As the annealing temperature increased, the islands were absorbed into the step edges. Thus the terraces were smoother and the step edges were more straightened. Well-defined surface with a step height of 0.2 nm was formed above $900^{\circ}C$. On the other hand, when the substrate was annealed at a fixed temperature of $1000^{\circ}C$, the change of surface morphology was observed for the substrate annealed for 10 min. After the annealing for 30 min, the surface on which any islands could not survive was observed.

• Applied Science and Convergence Technology
• /
• 제23권5호
• /
• pp.279-283
• /
• 2014

Al doped ZnO thin films have been deposited by a RF magnetron sputtering technique from a ZnO (2 wt.% $Al_2O_3$) target onto glass substrates heated at temperature ranging from RT to $400^{\circ}C$. X-ray diffraction analysis shows that the deposits have a preferential growth along the c-axis of a hexagonal structure. The full with at half maximum decreases from 0.45 to $0.43^{\circ}$ in the studied temperature range. The root main square surface roughness increases with substrate temperature from 1.89 to 2.67 nm. All films are transparent up to 80% in the visible wavelength range and the adsorption edge is red-shifted with substrate temperature from RT to $400^{\circ}C$. The sheet resistance increases from 92 ohm/sq to 419 ohm/sq when the deposition temperature increases from RT to $400^{\circ}C$. The increment of sheet resistance is caused by lowered carrier concentration resulting from an increase in surface roughness.

• 한국응용곤충학회지
• /
• 제42권1호
• /
• pp.9-13
• /
• 2003

꿀벌 2종 Apis mellifera L.(서양종)와 Apis cerana F.(동양종)일벌의 안테나, 다리 그리고 날개의 표피 탄화수소를 용매추출을 거치지 않고 직접 GC와 GC/MS를 이용하여 분석 하였다. 동양종과 서양종 일벌의 세 부위에서 nC22, nC23, nC25-nC3O, nC32 그리고 nC34와 같은 포화탄화수소를 검출하였고 nC24의 경우는 어느 종에서도 발견되지 않았다. 전체 포화탄화수소 중 nC26(23.0-42.6%)과 nC28(16.8-54.8%)의 함량비율이 높았고 나머지 포화탄화수소의 함량은 상대적으로 낮은 비율을 나타냈다. 서양종 일벌의 경우, 안테나, 날개 그리고 다리 부위에서 분석한 표피탄화수소 중 nC30, nC32 그리고 nC34가 항상 높은 함량비율로, nC25가 낮은 함량비율로 검출됨으로써 동양종 일벌과 구별할 수 있었다.

• 한국세라믹학회지
• /
• 제30권5호
• /
• pp.357-364
• /
• 1993

Chemical reaction occurred in the interface of Mn-Zn ferrite and glass after bonding. Effects of the formation of reaction layer on the magnetic properties were investigated. The composition of glass was 23PbO-61SiO2-6ZnO-8Na2O-2K2O and the ferrite was chosen to have a high permeability. Toroid samples of ferrites bonded with glasses, were heat-treated at $700^{\circ}C$, 80$0^{\circ}C$ and 90$0^{\circ}C$ for 1h. The reaction was observed to increase with bonding temperature, resulting in the development of reaction layer. Subsequently the initial permeability was found to be decreased. The permeabilities decreased by 25% with increasing bonding temperature from $700^{\circ}C$ to 80$0^{\circ}C$. At the bonding temperature of 90$0^{\circ}C$, the permeability was decreased by 45%, compared to that of 80$0^{\circ}C$.

• 한국세라믹학회지
• /
• 제36권2호
• /
• pp.159-166
• /
• 1999

티타니아가 첨가된 불투명한 실리카 에어로겔의 물성 및 열처리에 따른 미세구조 변화가 연구되었다. 부분가수 분해된 TEOS-이소프로판을 용액에 titanium isopropoxide를 첨가한후 겔화시킨 습윤겔을 초임계건조(25$0^{\circ}C$, 1250 psig)하여 모노리스 타입 에어로겔을 합성하였으며, SiO2-10 mol% TiO2 에어로겔의 밀도와 기공율은 각각 0.23 g/㎤와 90% 이었다. 초임계건조시 티타늄의 함량이 증가함에 따라 수축율이 증가할 뿐만 아니라 티타니아는 anatase 상으로 상전이됨과 동시에 입자 응집에 의해 100~800nm 크기의 cluster로 에어로겔 내에 균일하게 분포되었다. 불투명한 에어로겔은 8$mu extrm{m}$ 이하의 적외 영역에서 순수 실리카 에어로겔에 비하여 매우 낮은 광투과율과 $600^{\circ}C$까지 높은 미세구조 안정성을 보여주었다.

• 한국전기전자재료학회논문지
• /
• 제23권3호
• /
• pp.206-210
• /
• 2010

$BaTiO_3$ dielectric ceramics are widely used to multi-layer ceramic capacitor. The $BaTiO_3$ powder was synthesized at $950^{\circ}C$ by using a solid state reaction and grinded by using a high-energy mill. And then, 2.53 wt% glass frit was added to the synthesized $BaTiO_3$ powders for lowering the sintering temperature. The mixed powders were sintered at various temperatures of $1170^{\circ}C$, $1200^{\circ}C$, $1230^{\circ}C$. Microstructures of the sintered $BaTiO_3$ ceramics were inspected by SEM and crystal structures were analyzed by XRD method. The relative dielectric constant was measured by using a impedance/gain phase analyzer. The synthesized $BaTiO_3$ powder had the tetragonal perovskite structure without secondary phase and the particle size was below 200 nm. The relative densities measured at the samples sintered at the temperature above $1200^{\circ}C$ were about 95%. The relative dielectric constant showed maximum value of 2310, which was measured in the specimen sintered at $1200^{\circ}C$. From these results, we could know that the added glass frit had effects on both lowering the sintering temperature and improving the dielectric property.

• 대한환경공학회지
• /
• 제27권4호
• /
• pp.394-401
• /
• 2005

저온 플라즈마 연료개질 장치를 개발하여 여러 운전인자가 그 성능에 미치는 영향을 조사하였고 생성된 수소농후 개질가스를 무부하(Idle) 상태의 디젤엔진에 연소용 공기와 같이 주입하여 NO와 매연 저감효율에 미치는 영향을 조사하였다 전력 소모량이 증가할수록 개질반응의 점화가 더욱 용이하였으나 $H_2$ 농도, $H_2$ 수율, 에너지 전환율과 같은 저온 플라즈마 연료개질 장치의 성능은 O/C 비에 의해서만 영향을 받았는데 그 이유는 평형 반응온도가 O/C 비에 의하여 결정되기 때문이다. 저온 플라즈마 연료개질 장치에서의 $H_2$ 수율과 에너지 전환율은 O/C 비가 증가함에 따라 O/C 비가 $1.2{\sim}1.5$에서 33.4%와 66%의 최고값을 통과하였다. $H_2$ 수율과 에너지 전환율이 O/C 비가 $1.2{\sim}1.5$ 이하인 범위에서 O/C 비가 증가함에 따라 증가하는 이유는 O/C 비가 높아짐에 따라 완전 산화반응이 충분히 일어나서 반응온도가 높아지기 때문으로 보인다. O/C비가 $1.2{\sim}1.5$ 이상인 범위에서 O/C 비가 증가함에 따라 $H_2$ 수율과 에너지 전환율이 감소하는 현상은 과잉산소 조건에서 완전산화반응이 더욱 촉진되어 $H_2$ 수율과 에너지 전환율이 감소하였기 때문으로 보인다. 무부하 상태의 디젤엔진에 개질가스를 주입시 개질된 디젤/총디젤 무게비가 $18.2{\sim}23.5%$까지 증가할 때 NO저감효율과 매연제거효율은 각각 68.8%와 55.5%까지 증가하였다.

• Elastomers and Composites
• /
• 제47권1호
• /
• pp.9-17
• /
• 2012

본 연구에서는 클로로프렌 고무의 열 및 해수에 의한 노화 현상에 따른 물성 변화 및 사용 수명을 예측하였다. 가속 스트레스 수준은 열노화 $80^{\circ}C$, $100^{\circ}C$, $120^{\circ}C$, 해수침지노화 $40^{\circ}C$, $60^{\circ}C$, $80^{\circ}C$에서 2년 3개월(20,000Hr)동안 가속노화를 통해 인장시험을 수행하여 신장률, 인장강도, 경도를 통한 물성변화 측정을 하였다. 분석 결과신장율 저하가 가장 주된 고장지배모드임을 알 수 있었다. 아레누이스 식을 이용한 노화수명 예측 결과 열노화된 CR의 예측 수명은 $23^{\circ}C$에서 125년이며, 해수침지노화된 CR의 예측수명은 $23^{\circ}C$에서 9년이었다. SEM과 SEMEDS 분석 결과, 해수노화시편이 균열과 SEM-EDS에서는 산소의 농도가 증가하였으며, 이를 바탕으로 FT-IR에서는 해수와의 반응에 의하여 C-O와 C=O 결합이 생성되었음을 관찰하였다. 또한 DSC와 TGA 분석에서는 해수침지노화에 의하여 유리전이온도가 상승하며 분해온도가 낮아짐을 관찰하였다.

• Bulletin of the Korean Chemical Society
• /
• 제23권9호
• /
• pp.1263-1307
• /
• 2002

Pseudo-first-order rate constants (kobs) have been determined for the nucleophilic substitution reactions of p-nitrophenyl diphenyl phosphinate (PNPDPP) with substituted phenoxides (XC6H4O - ) and butane-2,3-dione monoximate (Ox- ) in 0.1 M borate buffer (pH = 10.0) at 25.0 ${\pm}0.1^{\circ}C$. The kobs value increases sharply upon addition of cethyltrimethylammonium bromide (CTAB) to the reaction medium up to near 7 ${\times}$ 10-4 M CTAB and then decreases smoothly upon further addition of CTAB. The rate enhancement upon the addition of CTAB is most significant for the reaction with -O2CC6H4O- and least significant for the one with C6H5O- , indicating that the reactivity of these aryloxides in the presence of CTAB cannot be determined by the basicity alone. The strength of the interaction of these anionic aryloxides with the positively charged micellar aggregates has been suggested to be an important factor to determine the reactivity in the presence of CTAB. The kobs value for the reaction with Ox- increases also upon the addition of CTAB. However, the increase in the kobs value is much more significant for the reaction with Ox- than for the one with ClC6H4O- , indicating that Ox- is less strongly solvated than ClC6H4O- in H2O. The ${\alpha}-effect$ shown by Ox- in H2O has been attributed to the ground-state solvation difference between Ox- and ClC6H4O- .

• 센서학회지
• /
• 제23권3호
• /
• pp.211-215
• /
• 2014

The Pt-, Ni- and Cr-decorated tubular $SnO_2$ nanofibers for gas sensors were prepared by the electrospinning of polyvinylpyrrolidone (PVP) nanofibers containing Pt, Ni, and Cr precursors, the sputtering of $SnO_2$ on the electrospun PVP nanofibers, and the removal of sacrificial PVP parts by heat treatment at $600^{\circ}C$ for 2 h. Pt-decorated tubular $SnO_2$ nanofibers showed high response ($R_a/R_g=210.5$, $R_g$: resistance in gas, $R_a$: resistance in air) to 5 ppm $C_2H_5OH$ at $350^{\circ}C$ with negligible cross-responses to other interference gases (5 ppm trimethylamine, $NH_3$, HCHO, p-xylene, toluene and benzene). Cr-decorated tubular $SnO_2$nanofibers showed the selective detection of p-xylene at $400^{\circ}C$. In contrast, no significant selectivity to a specific gas was found in Ni-decorated tubular $SnO_2$ nanofibers. The selective and sensitive detection of gases using Pt-decorated and Cr-decorated tubular $SnO_2$ nanofibers were discussed in relation to the catalytic promotion of gas sensing reaction.