• Journal of the Korean Institute of Rural Architecture
• /
• v.19 no.4
• /
• pp.57-65
• /
• 2017

Life quality in farming areas is declining these days on account of decrease in population with the outflow of young generations, advent of aging society, and also lack of social and physical infrastructure. To reverse this, the central and local governments have been devising policies in many ways; however, the vulnerable class in farming area suffering from financial difficulty is not supported with that properly. The results of applying insulation materials applicable to rural houses, EPS, e-board, and glass wool, actually to rural houses are summed as follows. EPS is the most inexpensive among the three installations in terms of material cost and expenses. The indoor and outdoor temperature difference increased from $0.9^{\circ}C$ to $2.5^{\circ}C$, and the temperature change reduced as $0.04^{\circ}C$. With e-board, the indoor and outdoor temperature difference increased from $3.3^{\circ}C$ to $7.5^{\circ}C$; however, the temperature change increased as $0.09^{\circ}C$. Unlike the other two methods, glass wool requires the additional installation of wooden frames. The material cost is highest, and the indoor and outdoor temperature difference increased from $1.1^{\circ}C$ to $8.0^{\circ}C$, and the temperature change reduced as $0.01^{\circ}C$. According to the results of measuring temperature, glass wool's temperature difference is measured to be the highest, but temperature change is found to be the most effective in EPS. Among the three insulation methods, EPS is the most economically advantageous as the material supply is easy and the cost is low. The material is easily processible, so ordinary town residents can install it easily, and it is effective at improving insulation performance, too. But this method cannot be applied when the house has walls that are not even. Also, as the insulator is thick, after the installation, the living space may be narrower as a result.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.34 no.1 s.114
• /
• pp.21-36
• /
• 2006

This study was undertaken to analyze the effects of pavement thermal properties and water retention characteristics on the surface temperature of the gray permeable cement concrete pavement during the summer. Following is a summary of major results. 1) The hourly surface temperature of pavement could be well predicted with a heat transfer model program that incorporated the input data of major meteorological variables including solar radiation, atmospheric temperature, dew point, wind velocity, cloudiness and the evaporation rate of the pavements predicted by the time domain reflectometry (TDR) method. 2) When the albedo was changed to 0.5 from an arbitrary starting condition of 0.3, holding other variables constant, the peak surface temperature of the pavement dropped by 11.5%. When heat capacity was changed to $2.5\;kJm^{-3}K^{-1}\;from\;1.5\;kJm^{-3}K^{-1}$, surface temperature dropped by 8.0%. When daily evaporation was changed to 1 mm from 2 mm, temperature dropped by 5.7%. When heat conductivity was changed to $2.5\;Wm^{-1}K^{-1}\;from\;1.5\;Wm^{-1}K^{-1}$, the peak surface temperature of the pavement fell by 1.2%. The peak pavement surface temperature under the arbitrary basic condition was $24.46^{\circ}C$ (12 a.m.). 3) It accordingly became evident that the pavement surface temperature can be most effectively lowered by using materials with a high albedo, a high heat capacity or a high evaporation at the pavement surface. The glare situation, however, is intensified by raising of the albedo, moreover if reflected light is absorbed into surrounding physical masses, it is changed into heat. It accordingly became evident that raising the heat capacity and the evaporative capacity may be the moot acceptable measures to improve the thermal characteristics of the pavement. 4) The sensitivity of the surface temperature to major meteorological variables was as follows. When the daily average temperature changed to $0^{\circ}C\;from\;15^{\circ}C$, holding all other variables constant, the peak surface temperature of the pavement decreased by 56.1 %. When the global solar radiation changed to $200\;Wm^{-2}\;from\;600\;Wm^{-2}$, the temperature of the pavement decreased by 23.4%. When the wind velocity changed to $8\;ms^{-1}\;from\;4\;ms^{-1}$, the temperature decreased by 1.4%. When the cloudiness level changed to 1.0 from 0.5, the peak surface temperature decreased by 0.7%. The peak pavement surface temperature under the arbitrary basic conditions was $24.46^{\circ}C$ (12 a.m.)

• Korean Journal of Environment and Ecology
• /
• v.36 no.6
• /
• pp.662-675
• /
• 2022

This study was intended to investigate and analyze the current status of the plant community structure in order to provide basic data for the systematic conservation and management of the Buxus sinica area appearing on the ridgeline connecting the Gyeokjabong(Mt.) and Keungiljae, on Bogildo Island. In consideration of location characteristics such as density, topography, and direction of B. sinica appearing in the shrub layers, a total of 26 sites were set as the survey area for representative vegetation communities or areas with changes in topography. According to DCA and TWINSPAN, it was classified into 6 communities, namely Carpinus turczaninovii-Deciduous broad-leaved, C. turczaninovii, C. turczaninovii-B. sinica, C. turczaninovii-Evergreen broad-leaved, Q. acuta, and D. trifidus-Q. acuta. The community dominated by C. turczaninovii maintains the status quo for the present moment, however, Q. acuta will dominate the surrounding area in the long term, so Q. acuta has high succesion potential. In the case of the Q. acuta and D. trifidus-Q. acuta communities, Q. acuta, known as the climax species of warm-temperate forests, will maintain dominant status. In a case of B. sinica, the community dominated by C. turczaninovii will remain in good status due to the topographical conditions, but the community dominated by Q. acuta growth difficulties are expected due to the high coverage. In the relationship between environmental factors and vegetation distribution, analysis showed that only soil pH affect vegetation distribution. Furthermore, the soil acidity (pH) was 3.78-5.30, the electrical conductivity was 0.186-0.543 dS/m, and the organic matter content was 2.25-2.89%.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.5
• /
• pp.13-21
• /
• 2014

This study generated regression models to quantify storage and annual uptake of carbon from five native landscape tree species through a direct harvesting method, and established essential information to estimate carbon reduction effects from urban greenspaces. Tree species for the study included the Chionanthus retusus, Prunus armeniaca, Abies holophylla, Cornus officinalis, and Taxus cuspidata, which are usually planted in cities of middle Korea, but for which no information on carbon reduction is available. Ten tree individuals for each species were sampled reflecting various stem diameter sizes at a given interval. The study measured biomass for each part including the roots of sample trees to compute total carbon storage per tree. The annual carbon uptake per tree was quantified by analyzing the radial growth rates of stem samples at breast height or ground level. Regression models were developed using diameter at breast height (dbh) or ground level (dg) as an independent variable to easily estimate storage and annual uptake of carbon per tree for each species. All the regression models showed high fitness with $r^2$ values of 0.92~0.99. Storage and annual uptake of carbon from a tree with dbh of 10 cm were greatest with C. retusus (20.0 kg and 5.9 kg/yr, respectively), followed by P. armeniaca (17.5 kg and 4.5 kg/yr) and A. holophylla (13.2kg and 1.8 kg/yr) in order. A C. officinalis tree and T. cuspidata tree with dg of 10 cm stored 9.3 and 6.3 kg of carbon and annually sequestered 3.2 and 0.6 kg, respectively. The above-mentioned carbon storage equaled the amount of carbon emitted from gasoline consumption of about 23~35 L for C. retusus, P. armeniaca, and A. holophylla, and 11~16 L for C. officinalis and T. cuspidata. A tree with the diameter size of 10 cm annually offset carbon emissions from gasoline use of about 6~10 L for C. retusus, P. armeniaca, and C. officinalis, and 1~3 L for A. holophylla and T. cuspidata. The study breaks new ground to easily quantify biomass and carbon reduction for the tree species by overcoming difficulties in direct cutting and root digging of urban landscape trees.

• Journal of electromagnetic engineering and science
• /
• v.7 no.3
• /
• pp.103-108
• /
• 2007

In this paper, a low-power 2.4 GHz front-end for sensor network application (IEEE 802.15.4 LR-WPAN) is designed in a 0.18 um CMOS process. A power supply circuit with a novel temperature-compensation scheme is presented. The simulation and measurement results show that the front-end (LNA, Mixer) can achieve a voltage gain of 35.3 dB and a noise figure(NF) of 3.1 dB while consuming 5.04 mW (LNA: 2.16 mW, Mixer: 2.88 mW) of power at $27^{\circ}C$. The NF includes the loss of BALUN and BPF. The low-IF architecture is used. The voltage gain, noise figure and third-order intercept point (IIP3) variations over -45$^{\circ}C$ to 85$^{\circ}C$ are less than 0.2 dB, 0.25 dB and 1.5 dB, respectively.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.9
• /
• pp.1-9
• /
• 1997

Novel class A CMOS second-generation current conveyors (CCII) using 0.6.mu.m n-well standard CMOS process for high-frequency current-mode signal processing were developed. The CCII consists of a regulated current-cell for the voltage input and a cascode current mirror for the current output. In this architecture, the two input stages are coupled by current mirrors to reduce the current input impedance. Measurements of the fabricated cCII show that the current input impedance is 308 .ohm. and the 3-dB cutoff frequency when used as a voltage amplifier extends beyond 10MHz. The linear dynamic ranges of voltage and current are from -0.5V to 1.5V and from -100.mu.A to +120.mu.A for supply voltage V$\_$DD/ = -V$\_$SS/=2.5V, respectively. The power dissipation is 2 mW and the active chip area is 0.2 * 0.2 [mm$\^$2/].

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.6
• /
• pp.173-179
• /
• 2012

The experiments, which analyze the injury symptoms and diagnose growth conditions utilizing IRVT and analyzing each parts of H. helix L., had been held under a low temperature. Greenhouse and outdoor growing Genus hedera had been prepared and compared with each Genus hedera's peak and bottom leaves' surface temperature under the experimental categories $-6^{\circ}C$ and $-12^{\circ}C$. As results, analyzing the surface thermal property of peak part leaves' of outdoor growing Genus hedera, at experimental categories $-6^{\circ}C$, $-12^{\circ}C$ were ranged from $-2^{\circ}C{\sim}-7^{\circ}C$ and $-2^{\circ}C{\sim}-15^{\circ}C$. On the other hand, the surface thermal property of bottom part leaves at experimental categories $-6^{\circ}C$, $-12^{\circ}C$ were ranged $-2^{\circ}C{\sim}-11^{\circ}C$ and $-1^{\circ}C{\sim}-12^{\circ}C$. It appears that the thermal properties of leaves' surface on $-6^{\circ}C$ peaks and $-12^{\circ}C$ bottoms were more broadband than bottoms and peaks. It means that the peaks were more sensitive than bottoms, as like $-2^{\circ}C{\sim}-15^{\circ}C$, $-1{\sim}-12^{\circ}C$. Moreover, as similar results had seen to leaves surface temperature added to cold wind conditions. How the cold wind damaged the outdoor growing Genus hedera, analyzed the surface thermal property by IRVT data under $0^{\circ}C$, $-2^{\circ}C$, $-4^{\circ}C$ condition, it resulted to $-6.2^{\circ}C$, $-6.8^{\circ}C$, $-7.5^{\circ}C$. It appeared more $3.5{\sim}6.2^{\circ}C$ low temperature than experimental setting point. In addition, each parts thurmal property of peaks and bottoms was not similar, it referred to each parts' sensitivities of low temperature were different on the peak and bottom leaves surface temperature.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.515-525
• /
• 2007

In this investigation, results of laboratory tests on four reinforced concrete flat plate interior connections with elongated rectangular column support which has been used widely in tall residential buildings are presented. The purpose of this study is to evaluate an effect of column aspect ratio (${\beta}_c={c_1}/{c_2}$=side length ratio of column section in the direction of lateral loading $(c_1)$ to the direction of perpendicular to $c_1$) on the hysteretic behavior under earthquake type loading. The aspect ratio of column section was taken as $0.5{\sim}3\;(c_1/c_2=1/2,\;1/1,\;2/1,\;3/1)$ and the column perimeter was held constant at 1200mm in order to achieve nominal vertical shear strength $(V_c)$ uniformly. Other design parameters such as flexural reinforcement ratio $(\rho)$ of the slab and concrete strength$(f_{ck})$ was kept constant as ${\rho}=1.0%$ and $f_{ck}=40MPa$, respectively. Gravity shear load $(V_g)$ was applied by 30 percent of nominal vertical shear strength $(0.3V_o)$ of the specimen. Experimental observations on punching failure pattern, peak lateral-load and story drift ratio at punching failure, stiffness degradation and energy dissipation in the hysteresis loop, and steel and concrete strain distributions near the column support were examined and discussed in accordance with different column aspect ratio. Eccentric shear stress model of ACI 318-05 was evaluated with experimental results. A fraction of transferring moment by shear and flexure in the design code was analyzed based on the test results.

• Korean Institute of Interior Design Journal
• /
• no.28
• /
• pp.33-43
• /
• 2001

Mario Botta is one of the modern architects who established his own architectural world on the basis of the architectural spirit of Modernism. His works have been a good theme not only for those who study architecture but also for those who study the relationship between architecture and the surrounding environment and there have been many published papers and reports on his works. However, most of them stressed on the importance of the external appearance of architecture or on the relationship between architecture and the surrounding environment. There have been relatively few studies that have dealt intensively with interior space. The aim of this study is to find the characteristics of interior space in public buildings that were designed by Botta and to analyze them from the view design principles and design elements. For this purpose, the five most important public buildings were selected and the public space of the building like the central hall, the lobby, and the foyer were analyzed. Through this study, the followings are realized. A) Spatial features: $\circled1$ Refined and graceful interiors where the principle of symmetry was applied, $\circled2$ Centripetal interiors surrounded by thick walls, $\circled3$ Interior design lit by skylights above the central area, B) Formative features: $\circled1$ The shapes of the external and internal spaces are identical, $\circled2$ Simple geometrical shapes were applied in defining the shapes of internal spaces, $\circled3$ Skylights and light wells were combined and were utilized as form elements, $\circled4$ Architectural vocabularies of Corbusier such as stairs, round pillars, and bridges were developed and utilized, $\circled5$ Utilized the geometry that resembled his architecture as a form element to the furniture, C) material pattern features: $\circled1$ Plainly expressed the patterns of bricks that appear in the course of construction, $\circled2$ Made and used horizontal stripe patterns using stones of different colors.

• Journal of Korean Society of Rural Planning
• /
• v.17 no.3
• /
• pp.27-41
• /
• 2011

This research The main focus of this research is to provide basic data for concrete recreation planning of future site by selecting Gwangmyeong-Siheung housing district, large residential development district focused on rural areas, by evaluation of recreation value and detailed biotope type classification. The main results of analysis are as follows. As a result of basic survey of the research area, total 79 family and 307 taxonomic groups are identified and also naturalization index and urbanization index were estimated 16.6 % and 17.6% respectively. Also, as a result of biotope type classification, it is divide into 12 biotope type gorups including forest biotope type group and its subordinate 53 biotop types. As a result of first value evaluation, there are total 13 biotope types such as vegetation-full artificial rivers in I grade. In addition it is analyzed as 9 types of II grade, 5 types of III grade, 8 types of IV grade, 18 types of V grade. Lastly, as a result of second evauation, it is analyzed that there are 21 special meaningful areas for recreation and natural experience(1a, 1b), and 50 meaningful areas for recreation and natural experience(2a, 2b, 2c). It is regarded that the results of biotope types classification and recreation value from this research play roles of analyzing the Suitable site for recreation area before development in terms of large residential development district, and then these results provide important basic data to secure recreational and natural experience area in development planning.