• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.319-325
• /
• 2005

A signal processing method for white light interferometry (WLI), which performs a series of analog signal processing steps to locate the central interference fringe position at high speed: is developed and applied to a WLI temperature sensor system. We found that the new method has random walk of $0.019^{\circ}C/\sqrt{Hz}$ with good linearity. However, the temperature change in the path-matching interferometer results in drift of the measured sensor output. The temperature dependence of drift in the WLI temperature sensor system, was calculated to be $1.42{\mu}m/^{\circ}C$. It is also found that the relationship between the peak spacing in the interferogram and the spacing measured by the method can be nonlinear when the fringe spacing is comparable to the coherence length of the source.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1141-1146
• /
• 2012

Ce-doped $Y_3Al_5O_{12}$ (YAG:Ce) phosphor powder was prepared using a ${NO_3}^-$-malonic acid-$NH_4NO_3-NH_3{\cdot}H_2O$ system. The YAG:Ce precursor was ignited at $240^{\circ}C$ and the resulting powder contained YAG:Ce crystallites (42%) - active in the visible region at 460 nm - amorphous particles (53%) - inactive at visible wavelengths - and less than 3% oxide (3%) crystallite impurities. The impurities transformed to acitive YAG:Ce crystallites at above $800^{\circ}C$. At above $1000^{\circ}C$, the amorphous phase became YAG phase and isolated $Ce_2O$ crystallites emerged. The powder particles comprised < $4{\mu}m$ secondary aggregates of 20 nm primary particles. The thermal dusting of the secondary particles coincided with the aggregation of the secondary particles at above $900^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.323-324
• /
• 2007

Investigation of improving the properties of UV photodetector which uses the wide bandgap of ZnO are under active progress. In this paper, transparent conducting aluminum-doped Zinc oxide films(AZO) were prepared by rf magnetron sputtering on glass(corning 1737) and p-Si substrate, were then annealed at temperature $400^{\circ}C$ for 2hr. The AZO thin films were deposited by RF sputtering system. HF power and work pressure is 120 W and 15 mTorr, respectively, and the purity of AZO target is 5N. The AZO thin films were deposited at 300, 400, $500^{\circ}C$, and $600^{\circ}C$. For sample deposited at $400^{\circ}C$, we observed best $V_r-I_{ph}$ of 0.94 mA and good transmittance.

• Korean Journal of Optics and Photonics
• /
• v.3 no.3
• /
• pp.178-182
• /
• 1992

An air-cooled discharge-heated copper-vapor laser system with its inter-electrode distance of 45 cm has been developed by utilizing an alumina ceramic plasma tube of 1.6 cm in diameter and 50 cm in lengih. For operating the laser, a dc high voltage power supply with output rating of 6 kV and 500 mA, a resonant charging circuitry consisting partly of an 1.8 H inductor assembly and a 5 nF storage capacitor, and a thyratron driver operating up to 7 kHz have also been developed. The present laser system starts lasing at the tube temperature of about $1350^{\circ}C$ and an maximum average output power of 0.7 W has been obtained at 12 kV, 4.5 kHz. 50 mbar of Ne buffer gas pressure, and at the tube temperature of $1460^{\circ}C$.

• Resources Recycling
• /
• v.14 no.2
• /
• pp.19-27
• /
• 2005

The recycling possibility of aluminum waste dross(AWD) as a ceramic raw material of porous light-weight material was examined. A aluminum waste dross was washed 4-7 consecutive times and roasted at 900$^{\circ}% for 1hour as pre-treatments. The properties of the pre-treatment of aluminum waste dross was investigated. It was conformed by XRD result that the spinel crystalline was grown in AWD, after roasting. After the roasted AWD was ground in aqueous state, the sodium hexaphosphate(SHP) as a dispersant which is used for stabilizing the concentrated slurry was added to the AWD slurry. The porous material was prepared by slurry foaming method with surfactant at room temperature. The foamed slurry volumes were 2 and 3 times of the original slurry volume. The properties of porous material with extended volume of 3 times was following: the porosity was about 84%, bulk density was 0.59 g/cm$^3$, the range of pore was from 50 ${\mu}m$ to 500 ${\mu}m$ and mean pore size was about 200 ${\mu}m$. AWD porous material was sintered at 1150$^{\circ}C-1250$^{\circ}C. It was colcluded that AWD was sintered well at 1200$^{\circ}C from material surface observation by SEM.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.231-238
• /
• 1998

Cr3C2 -dispersed TiC composites were prepared via HPCS(high pressure-self combustion sintering) pro-cess using mixtures of Ti, Cr and a carbon source for the purpose of increasing the facture toughness and sinterability of TiC. In this study the microstructure and properties of the composites were investigated in terms of relation to the carbon source the particle size of Ti and the amount of Cr. It was found that car-bon black was the most effective carbon source among the various carbon sources tested and the reaction was more effective as the particle size of Ti decreased. Among the sintered composites of Ti-C-Cr system the one with 30wt% Cr showed the best physical properties with 0.5% in apparent porosity 98.8% in re-lative density 18.2 GPa in hardness and 4.46 MPa.m1/2 in fracture toughness. In addition it was observed that the lattice constant of TiC decreased gradually with increasing the amount of Cr.

• Journal of Internet Computing and Services
• /
• v.8 no.4
• /
• pp.51-59
• /
• 2007

This paper presents the development of RFID educational system based on using 900MHz air interface between the reader and the active tag. The software of reader and the active tag is developed on embedded environment, and the software of PC controlling the reader is based on window OS operated as the server. The AT89C51ED2 VLSI chip is used for the processor of the reader and the active tag. As the development environment, Keil compiler is used for the reader and the active tag of which the programing language is C. The visual C language of the visual studio on the PC activated as the server is used for development language. To verify the function of the system, PC gets the tag's identification number through the reader and send the data to with the active tag memory a certain contents as "wite" operation. Finally the data written from the active tag's memory is sent to the PC via the reader as "read" operation and compare the received data with one already sent to the tag.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1091-1092
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.199-200
• /
• 2006

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.177-182
• /
• 1997

The purpose of this study is to analyze how tools, guide bush type and the change of cutting speed have effects on the diameter of cutting hole, surface roughness of workpiece and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. (1) The diameter was expanded for 25${\mu}{\textrm}{m}$ at the first section and then was reduced 0${\mu}{\textrm}{m}$ and 15${\mu}{\textrm}{m}$ respectively at the 10m and 20m section comparing to the diameter of tool with respect to the variation of cutting length. (2) It was proved that roughness was below 12S for the whole section of cutting length. (3) The roundness has been below 12${\mu}{\textrm}{m}$. Regarding the polygon phenomenon, it has bee proved that not only uneven number of angle but also even number (quadrilateral, elliptical) of angle were made. (4) Variation of diameter, surface roughness of workpiece and roundness turned out to ve the best at 70m/min of cutting speed, 0.15mm/rev of feed.