• Food Science and Preservation
• /
• v.15 no.4
• /
• pp.606-611
• /
• 2008

Myungran Jeotkal, Korean fermented seafood, and its ingredients(hot red pepper powder, ginger, garlic, and seasoning mix) were irradiated with 0, 0.5, 1.0, 2.0, and 5.0 kGy of gamma rays and stored at 4C for 4 weeks to determine changes in microbiological and sensory characteristics. Water activities of Myungran Jeotkal, hot red pepper powder, ginger, garlic, and seasoning mix were 0.89 0.56, 0.98, 0.99, and 0.07, respectively. Myungran Jeotkal was observed to be initially contaminated. Total aerobic bacteria, yeast and mold, and coliform levels were 6.7, 4.3, and 3.6 log CFU/g, respectively. Irradiation at 2 kGy afforded approximately a 4 log reduction in total aerobic bacteria, and a 3 log drop in both yeast and mold levels and coliform bacteria(P<0.05). No viable microbial cells were detected in Myungran Jeotkal after 5 kGy of irradiation(at a detection limit of 101 CFU/g). The total aerobic bacterial level in red pepper powder was 6.3 log CFU/g and this component, of the tested ingredients, contributed most to the microbial contamination of Myungran Jeotkal. The initial count of total aerobic bacteria, 6.3 log CFU/g, was significantly reduced to 4.5 log CFU/g after irradiation(P<0.05). Sensory evaluation showed that gamma irradiation of up to 5.0 kGy did not adversely affect overall acceptability of Myungran Jeotkal or its ingredients during cold storage. Therefore, gamma irradiationwas effective to extend the shelf-life of Myungran Jeotkal.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.3
• /
• pp.268-276
• /
• 2015

In this study, $CO_2$ reduction type quaternary component high fluidity concrete was produced with more than 80% reduction in cement quantity to increase the use of industrial byproducts and enhance construction performance, thereby reducing $CO_2$ emissions. Furthermore, the quality properties, and $CO_2$ reduction performance of this concrete were evaluated. As a result of the quality evaluation of quaternary component blended high fluidity concrete with $CO_2$ reduction, the target performance could be achieved with a 80% or more reduction of cement quantity by mixing a large amount of industrial byproducts. The required performance level was obtained even though the flow, dynamic, and durability characteristics decreased a little compared to conventional mix. In addition, to analyze the $CO_2$ reduction performance of quaternary component blended high fluidity concrete with $CO_2$ reduction, the life cycle assessment (LCA) of the concrete was performed and the results showed that compared to the conventional mix, the carbon emissions decreased by 62.2% and the manufacturing cost by 24.5%.

• Journal of the Korean Chemical Society
• /
• v.53 no.2
• /
• pp.118-124
• /
• 2009

The values of critical micelle concentration (CMC) and counter ion binding constants (B) in a micellar state of CPC (1-hexadecylpyridinium chloride) with Brij 35 (polyoxyethylene(23) lauryl ether) in water were determined as a function of ${\alpha}_1$ (the overall mole fraction of CPC) by the use of electric conductivity method. Various thermodynamic parameters ($X_i,\;{\gamma}_i,\;C_i,\;a_{i}^{M},\;\beta,\;and\;{\Delta}H_{mix}$) were calculated and analyzed by means of the equations derived from the non-ideal mixed micellar model. And thermodynamic parameters (${\Delta}{G^o}_m,\;{\Delta}{H^o}_m,\;and\;{\Delta}{S^o}_m$) for the micellization of CPC/Brij 35 mixtures were also calculated from the temperature dependence of the CMC values. The values of ${\Delta}{G^o}_m$ are all negative, but the values of ${\Delta}{S^o}_m$ and ${\Delta}{H^o}_m$ are positive or negative, depending on the measured temperature and ${\alpha}_1$.

• Journal of the Korea Concrete Institute
• /
• v.23 no.4
• /
• pp.431-440
• /
• 2011

Concrete structures exposed to fire produce changes in their internal structure, resulting in their service life reduction due to the deterioration of its strength and performance capacity. The deterioration level are dependent on the temperature, exposure time, concrete mix proportions, aggregate property, and material properties. This study was performed to evaluate the thermal behavior of ultra-high strength concrete for the parameters of water to cement ratio (compressive strength), fine to total aggregate ratio, and maximum coarse aggregate size. At room temperature and $500^{\circ}C$, tests of ultrasonic pulse velocity, resonance frequency, static modulus of elasticity, and compressive strength are performed using ${\varnothing}100{\times}200\;mm$ cylindrical concrete specimens. The results showed that the residual mechanical properties of ultra-high strength concrete heated to $500^{\circ}C$ is influenced by variation of a water to binder ratio, fine to total aggregate ratio, and maximum coarse aggregate size.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.31.2-31.2
• /
• 2011

We studied a method of manufacturing an anode to restrict contraction in reducing NiO/YSZ by uniformly mixing. In order to mix Ni and YSZ, a sub-micron Ni core surface was coated at high-speed by a mixture of nano-sized YSZ and a spherical core-shell was subsequently formed. The micron-sized core-shell anode powder was then heat treated at $400{\sim}1,450^{\circ}C$ in an air atmosphere and Ni was extruded and synthesized in nano-size. Subsequently, when the nano-sized mixture of the anode was heat treated and maintained at a temperature of $1,450^{\circ}C$, the anode was manufactured, where Ni and YSZ were uniformly distributed with the nano-structure. According to the nano-sized anode powder synthesis process, Ni particles were oxidized at $400{\sim}500^{\circ}C$ and became spherical by surface tension. In the case of the spherical core Ni powder, the heat treatment temperature rose to $1,250^{\circ}C$ and then a gap between the internal and external pressures occurred due to thermal and tensile stresses. A crack subsequently appeared on the surface, and the heat treatment temperature was increased continuously to increase the pressure gap and then the core Ni extruded as a nano-sized powder, Ni and YSZ uniformly distributed. It was found that the anode of 50~200 nm with a consistent structure obtained in this study has electric conductivity that is approximately 3 times larger than that of a commercial anode.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.2 no.2 s.5
• /
• pp.61-72
• /
• 2002

The optimum fiber and asphalt binder contents were decided on the base of the Mashall mix design method. To compare the mechanical characteristics between the conventional(dense-graded 20) and the fiber-reinforced mixtures, indirect tension tests were conducted under three temperatures(5, 20, 60$^{\circ}C$). In particular, the wheel tracking tests were performed to evaluate the rutting resistances of the mixtures. Test results showed that the indirect tensile strength of fiber-reinforced asphalt concrete was higher than that of conventional one. The toughness of fiber-reinforced mixture was 1.27 to 1.97 times higher than that of conventional one, depending upon the temperature. In addition, the results of wheel tracking tests and the retained indirect splitting tension tests conducted at $60^{\circ}C$ revealed that the resistance to permanent deformation of fiber-reinforced mixture was stronger than that of the conventional one.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.1
• /
• pp.79-87
• /
• 1997

A study on the processing method of anchovy hydrolysate paste (AHP) was carried out to improve the sensory quality of salted and fermented fish. Homogenized whole anchovy was hydrolyzed using commercial pretenses, Complex enzyme-2000 (CE, Pacific Chem. Co.) and Alcalase (AL, Novo), in a cylindrical vessel with 4 baffle plates and 6-bladed turbine impeller. Optimal pH, temperature, and enzyme concentration for the hydrolysis with CE and AL were $7.0,\;52^{\circ}C,\;7\%$, and $8.0,\;60^{\circ}C,\;6\%$, respectively. The rational amount of water for homogenization, agitation speed, and hydrolyzing time were $100\%\;(w/w)$, 100 rpm, and 210 min, respectively. To make the hydrolysate to paste type, it was effective to mix the additives, such as starch, soybean protein, agar, and carrageenan gum to the hydrolysate 5 min before the end of boiling at $100^{\circ}C$ for 30 min. Minimal NaCl concentration for long-term preservation was $15\%$, and this could be reduced to $12\%$ by adding $5\%$ of KCl. yield of the AHP based on the total nitrogen content was $94.6\~97.0\%,\;and\;86.0\~89.2\%$, of the nitrogen was amino nitrogen. Salinity, pH and histamine content of the AHP prepared with $12\%$ NaCl and $5\%$ KCl were $9.3\~9.9\%,\;6.1\~6.2$, and below 13 mg/100 g, respectively. The AHP was stable at $26{\pm}3^{\circ}C$ for 60 days on bacterial growth, and addition of $0.05\%$ of rosemary (Herbalox) extract was effective to inhibit the lipid oxidation of the AHP during storage.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.4
• /
• pp.95-104
• /
• 2004

A styrene solution of waste expanded polystyrene with a crosslinking agent and an initiator was used as a binder for waste wood-plastic composite panels. The waste wood-plastic composite panels are prepared with various binder contents and filler-binder ratios by using a hot press molding method. The apparent density of the composite panels is increased with increasing binder content and filler-binder ratio, while their water absorption and expansion in thickness are decreased with increasing binder content and filler-binder ratio. The maximum flexural strength and wet flexural strength of the composite panels are obtained at a binder content of 35% and a filler-binder ratio of 0.8. Decreases in the flexural strengths of the composite panels due to water immersion at 20 and $100^{\circ}C$ are hardly recognized at binder contents of 30% or more.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.141-148
• /
• 1996

The pulished works on Accelerated Curing Effect were generally performed around from 1960 to 1970th century for 18 to 24 hours - total curing periods. It is not possible to define the effect of temperature rise because those results were obtaine mainly by using the manually operated steam-curing tank. Thus, it may not be available to apply those data immediately on the domestic PC wall production line. The testing specimens were made from the standard mix proportion according to those of domestic PC factories to establish a basic data for the Accelerated Curing Effect. The experimental tests were conducted according to the conditions of each sub-curing periods. By comparing the results of compression tests on de-molded and 28-day water-curing specimens, we find that the most effective curing condition to obtain more than the required design strength after 28 day of water curing may be as follows: the presteaming period does not affect seriously and less than$30^{circ}C/hr$- the rate of temperature rise andless than $82^{circ}C$ - maximum temperature are necessary. It seems that post-curing procedure is very important factor to increase the effect of accelerated curing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.273-280
• /
• 2002

The stochiometric mix of evaporating materials for the CuGaTe$_2$ single crystal thin films was prepared from horizontal furnance. For extrapolation method of X-ray diffraction patterns for the CuGaTe$_2$ polycrystal, it was found tetragonal structure whose lattice constant a$\_$0/ and c$\_$0/ were 6.025 ${\AA}$ and 11.931 ${\AA}$, respectively. To obtain the single crystal thin films, CuGaTe$_2$ mixed crystal was deposited on throughly etched semi-insulator GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were 670 $^{\circ}C$ and 410 $^{\circ}C$ respective1y, and the thickness of the single crystal thin films is 2.1 $\mu\textrm{m}$. The crystalline structure of single crystalthin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). Hall effect on this sample was measured by the method of van der Pauw and studied on carrier density and mobility dependence on temperature. The carrier density and mobility of CuGaTe$_2$ single crystal thin films deduced from Hall data are 8.72${\times}$10$\^$23/㎥, 3.42${\times}$10$\^$-2/㎡/V$.$s at 293K, respectively. From the photocurrent spectrum by illumination of perpendicular light on the c - axis of the CuGaTe$_2$ single crystal thin film, we have found that the values of spin orbit coupling Δs.o and the crystal field splitting Δcr were 0.0791 eV and 0/2463eV at 10K, respectively. From the PL spectra at 10K, the peaks corresponding to free bound excitons and D-A pair and a broad emission band due to SA is identified. The binding energy of the free excitons are determined to be 0.0470eV and the dissipation energy of the donor -bound exciton and acceptor-bound exciton to be 0.0490eV, 0.00558eV, respectively.