• Journal of Bio-Environment Control
• /
• v.10 no.4
• /
• pp.232-236
• /
• 2001

Four air temperature levels of 23, 25, 27 and 29$^{\circ}C$, three humidity levels of 85, 90 and 95% R.H. at photosynthetic photon flux (PPF) of 50 $\mu$mol.m$^{-2}$ .s$^{-1}$ were provided to investigate the effect of vapor pressure deficit on the evapotranspiration rate (EVTR) and graft-taking of watermelon grafted seed-increase. Thus EVTR of grafted seedlings increased with increasing air temperature at high humidity of 95%R.H. At relatively low humidity of 85% R.H., grafted seedlings showed a high EVTR and some wilting of scions was observed at this condition. This result would be ascribed to the low supply of water to vascular bundles according to the insufficient joining of scions and rootstocks. Differences in EVTR between 90% R.H. and 95% R.H. were not observed. Grafted seedlings showed high graft-taking at high relative humidity. Relative humidity had highly influenced to the graft-taking as compared to the air temperature. Graft-taking increased with decreasing vapor pressure deficit. Graft-taking greater than 90% was found at vapor pressure deficit less than 0.4kPa which could be obtained at humidity higher than 90% R.H. Therefore it is required to control the humidity higher than 90% R.H. for suppressing EVTR of grafted seedlings and preventing some wilting of scoins and thus enhancing the graft-taking of grafted seedlings.

• 한국해양학회지
• /
• v.24 no.1
• /
• pp.52-61
• /
• 1989

The daily net primary production by phytoplankton and ammonium excretion by macrozooplankton (> $350{\mu}m$) were measured to understand the nitrogenous nutrient dynamics in the southern part of the East Sea of Korea. At most of the staions, water columns were well stratified and strongly developed pycnoclines and matching nutriclines could be found near the 20-60m. Total chlorophyll ranged between $1.22-3.24{\mu}g$ ChI/l and nano-fractions of chlorophyll ranged from 43.2 to 99.6% in the surface layer. The daily net primary production by phytoplankton ranged from 0.75 to 2.04 gC/$m^2$/d and averaged to be 1.5 gC/$m^2$/d. 1t is evidenced that the primary production and chlorophyll content are relatively high in frontal waters where the North Korean Cold Water meets with the East Korean Warm Water. The turnover time of nitrate in the euphotic zone ranged from 0.2 day to 1.6 day and averaged to be 0.8 day. The N:P ratio of the study area shows on the average 13.4 which indicates nitrogenous nutrient to be the limiting factor for phytoplankton growth. Ammonium excretion by macrowoplankton averaged out to 1.3mg at-N/$m^2$/d, and contributed 7.3% of daily total nitrogen requirement by phytoplankton in this area. Calculation of upward flux of nitrate to the surface mixed layer from the lower layer approximates 7% of nitrogen requirement by phytoplankton.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.77-77
• /
• 1998

Present silicon dioxide (SiOz) 떠m as intennetal dielectridIMD) layers will result in high parasitic c capacitance and crosstalk interference in 비gh density devices. Low dielectric materials such as f f1uorina뼈 silicon oxide(SiOF) and f1uoropolymer IMD layers have been tried to s이ve this problem. I In the SiOF ftlm, as fluorine concentration increases the dielectric constant of t뼈 film decreases but i it becomes unstable and wa않r absorptivity increases. The dielectric constant above 3.0 is obtain어 i in these ftlms. Fluoropolymers such as polyte$\sigma$따luoroethylene(PTFE) are known as low dielectric c constant (>2.0) materials. However, their $\alpha$)Or thermal stability and low adhesive fa$\pi$e have h hindered 야1리ru뚱 as IMD ma따"ials. 1 The concept of a plasma processing a찌Jaratus with 비gh density plasma at low pressure has r received much attention for deposition because films made in these plasma reactors have many a advantages such as go여 film quality and gap filling profile. High ion flux with low ion energy in m the high density plasma make the low contamination and go어 $\sigma$'Oss피lked ftlm. Especially the h helicon plasma reactor have attractive features for ftlm deposition 야~au똥 of i앙 high density plasma p production compared with other conventional type plasma soun:es. I In this pa야Jr, we present the results on the low dielectric constant fluorocarbonated-SiOF film d밑JOsited on p-Si(loo) 5 inch silicon substrates with 00% of 0dFTES gas mixture and 20% of Ar g gas in a helicon plasma reactor. High density 띠asma is generated in the conventional helicon p plasma soun:e with Nagoya type ill antenna, 5-15 MHz and 1 kW RF power, 700 Gauss of m magnetic field, and 1.5 mTorr of pressure. The electron density and temperature of the 0dFTES d discharge are measUI벼 by Langmuir probe. The relative density of radicals are measured by optic허 e emission spe따'Oscopy(OES). Chemical bonding structure 3I피 atomic concentration 따'C characterized u using fourier transform infrared(FTIR) s야3띠"Oscopy and X -ray photonelectron spl:’따'Oscopy (XPS). D Dielectric constant is measured using a metal insulator semiconductor (MIS;AVO.4 $\mu$ m thick f fIlmlp-SD s$\sigma$ucture. A chemical stoichiome$\sigma$y of 야Ie fluorocarbina$textsc{k}$영-SiOF film 따~si야영 at room temperature, which t the flow rate of Oz and FTES gas is Isccm and 6sccm, res야~tvely, is form려 야Ie SiouFo.36Co.14. A d dielec$\sigma$ic constant of this fIlm is 2.8, but the s$\alpha$'!Cimen at annealed 5OOt: is obtain려 3.24, and the s stepcoverage in the 0.4 $\mu$ m and 0.5 $\mu$ m pattern 킹'C above 92% and 91% without void, res야~tively. res야~tively.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.2
• /
• pp.101-106
• /
• 1999

The down-core distribution of chlorophyll a, organic carbon contents and ${\delta}^{13}C$ in the bottom sediments were measured to understand the evolution of eutrophication in Masan Bay. Bottom sediment were collected in January 1994. The chlorophyll a and organic carbon contents in the sediment core decreased with increasing sediment depth, respectively. Bottom sediments (0~20 cm) in Masan Bay was rich in chlorophyll a (avg. 9.6 ${\mu}g\;g^{-1}$ dryweight) and organic C (avg. 2.5%). The down-core distribution of chlorophyll a suggests that the inner part of Masan Bay has experienced the acceleration of chlorophyll a supply since 1960s. Flux of organic carbon to the sea floor is in the range of 10 $gCm^{-2}\;yr^{-1}$ assuming the C:Chl a ratio of 25. It suggests tht approximately 1.3% of the fixed carbon by phytoplankton appears to be deposited in the bottom sediments.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.549-560
• /
• 2016

The purpose of this study is to identify the material characteristics of blackwares excavated from the Bonggok kiln site in Jinan-gun, Jeollabuk-do Province, South Korea, by scientific analyses and a reproduction experiment. Scientific analyses were conducted to determine the physical properties, chemical composition and for microscopic observation of blackwares. A reproduction experiment was also conducted by producing ceramic samples with black glaze, red ocher and limestone, and then cross sections of the samples were observed. The analysis results showed that all the excavated blackwares have similar properties such as chromaticity, specific gravity, absorption factor and porosity, but there is a difference depending on the crystallization of the ceramics. Thermal analysis showed that the exothermic peak was observed at about $1200^{\circ}C$, and crystal structure analysis indicated the presence of mullite. Hence, it can be concluded that the firing temperature of the excavated blackwares was around $1100-1200^{\circ}C$. Moreover, the glaze present on these blackwares has about 22% higher $Fe_2O_3$ content than those excavated from other places; however, the former has lower CaO content. For the reproduction experiment, samples were made using limestone as a flux and red ocher as a glaze. The results show that the cross section of the glaze layer of the reproduced sample have iron crystals with dendritic structures, similar to those present in the excavated black-wares. It is assumed that such iron crystals were formed during the process of melting and solidification of the iron oxide present in the blackwares.

• Journal of the Korean earth science society
• /
• v.30 no.6
• /
• pp.709-720
• /
• 2009

Field observation and numerical experiments were conducted to understand the impact of water retention pavement on the surface heat budget and on the regional circulation. The numerical model applied in this study is the atmospheric dynamic model Local Circulation Model (LCM) with two dimensional grid system, and a field observation was carried out under the clear sky and calm conditions of the weather on 19 July 2007. In the field observation, the maximum value of surface temperature on pavement covered with water retention material reached the $41.2^{\circ}C$ at 1430 LST and the values was lower for $16.1^{\circ}C$ than that of asphalt without the material. The Case BET03 assumed to be 0.3 for the surface evaporation efficiency was in good agreement with the observation and its sensible and latent heat fluxes were numerically estimated to be 229 and 227 $W/m^2$, respectively. Results of the numerical experiments demonstrated that the water retention pavement tends to induce the increase of latent heat flux associated with the lower surface temperature and mixing height during the daytime. Discontinuity of latent heat caused by the water retention pavement also tends to promote the development of mesoscale circulation called as land-land breeze or country breeze.

• Journal of Radiation Protection and Research
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2001

Sintered LiF:Mg,Cu,Na,Si thermoluminescence (TL) pellets were developed for application in radiation dosimetry. In the present study, the TL dosimetric properties of LiF:Mg,Cu,Na,Si TL pellets have been investigated for emission spectrum, dose response, energy response, and fading characteristics. LiF:Mg,Cu,Na,Si TL pellets were made by using a sintering process, that is, pressing and heat treatment from TL powders. Photon irradiations for the experiments were carried out using X-ray beams and a $^{137}Cs$ gamma source at the Korea Atomic Energy Research Institute (KAERI). The average energies and the dose were in the range of 20-662 keV and $10^{-6}-10^{-2}\;Gy$, respectively. The glow curves were measured with a manual type TLD reader(System 310, Teledyne) at a constant nitrogen flux and a linear heating rate. For a constant heating rate of $5^{\circ}C\;s^{-1}$, the main dosimetric peak of glow curve appeared at $234^{\circ}C$, the activation energy was 2.34 eV and frequency factor was $1.00{\times}10^{23}$. TL emission spectrum is appeared at the blue region centered at 410 nm. A linearity of photon dose response was maintained up to 100 Gy. The photon energy responses relative to $^{137}Cs$ response were within ${\pm}20%$ at overall photon energy region. The fading of TL sensitivity of the pellets stored at the room temperature was not found for one year.

• Clean Technology
• /
• v.20 no.2
• /
• pp.146-153
• /
• 2014

In this study, the effect of alkanolamine additives, 2-amino-2-methyl-1-propanol (AMP) and 2-amino-2-methyl-1,3-propanediol (AMPD) on $CO_2$ absorption rate of $K_2CO_3$ solution and the formation of $KHCO_3$ crystals was investigated. The normalized $CO_2$ flux and the equilibrium $CO_2$ partial pressure were measured for 5 wt% additives and 30 wt% $K_2CO_3$ mixtures using a wetted-wall column unit at $40^{\circ}C$ and $60^{\circ}C$. Both additives showed the increased $CO_2$ absorption rate and lowered the equilibrium $CO_2$ partial pressure acting as promoters. Besides, AMPD which has two hydroxyl groups enhanced the formation of $KHCO_3$ solid product separated from the $CO_2$-rich solution from the results of batch cooling crystallization experiments.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.243-260
• /
• 2018

A literature review on the effects of high temperature and radiation on radiation shielding concrete in Spent Fuel Dry Storage is presented in this study with a focus on concrete degradation. The general threshold is $95^{\circ}C$ for preventing long-term degradation from high temperature, and it is suggested that the temperature gradient should be less than $60^{\circ}C$ to avoid crack generation in concrete structures. The amount of damage depends on the characteristics of the concrete mixture, and increases with the temperature and exposure time. The tensile strength of concrete is more susceptible than the compressive strength to degradation due to high temperature. Nuclear heating from radiation can be neglected under an incident energy flux density of $10^{10}MeV{\cdot}cm^{-2}{\cdot}s^{-1}$. Neutron radiation of >$10^{19}n{\cdot}cm^{-2}$ or an integrated dose of gamma radiation exceeding $10^{10}$ rads can cause a reduction in the compressive and tensile strengths and the elastic moduli. When concrete is highly irradiated, changes in the mechanical properties are primarily caused by variation in water content resulting from high temperature, volume expansion, and crack generation. It is necessary to fully utilize previous research for effective technology development and licensing of a Korean dry storage system. This study can serve as important baseline data for developing domestic technology with regard to concrete casks of an SF (Spent Fuel) dry storage system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.5
• /
• pp.192-202
• /
• 2019

Physicochemical properties and sintering characteristics of pottery stone (Taebaek, Haenam, Aphae, Haengnam) were evaluated as a raw material for porcelain products. Due to acid leaching procedure, the concentration of iron oxide ($Fe_2O_3$) was decreased to < 1.0 wt%, which affects the whiteness of sintered samples. Mean particle size of acid leached samples is $5.7{\sim}10{\mu}m$ with narrow particle size distribution (PSD), which is lower than that of the pristine ($8{\sim}18{\mu}m$) with broad PSD. According to phase analysis by X-ray diffraction, most of pottery stones (PS) have Quartz phase as a main phase with Pyrophyllite as a second phase, however, Haenam PS shows halloysite phase. The absorption rate was in order of Taebaek (A, B, C)~Aphae (A, B) < Taebaek (Special A) < Haengnam < Haenam, and the samples sintered in reductive atmosphere showed lower absorption rate. This result might be due to the concentration of feldspar contained in PS, working as a flux in sintering process. Comparing the color of the sintered samples, the whiteness of refined PS (Taebaek special A, Haenam, Hangnam) is higher than acid leached PS (Taebaek A/B/C, Aphae A/B). The whiteness (L*) for refined PS is 95~97 %, which is higher than acid leached (82~96 %). This might be due to lower iron oxide concentration of the refined PS (0.11~0.58 %) than those of the acid leached PS (0.41~1.91 %) even though most of iron oxide was removed by acid leaching.