• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.247-250
• /
• 2006

The growing demand for more fuel-efficient vehicles to reduce energy consumption and air pollution is a challenge for the automotive industry. The characteristic properties of aluminum, high strengrth stiffness to weight ratio, good formability, good corrosion resistence, and recycling potential make it the ideal candidate to replace heavier materials in the car to respond to the weight resuction demand within the automotive industry. In this paper, A series of compression test was carried out to find the flow stress of A6082 at 300, 400 and $500^{\circ}C$, then we tried to estimate weldability, extrusion load and effective stress of die in the aluminum extrusion process through the 3D FE simulation at non-steady state for aluminum automotive parts.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.2C no.5
• /
• pp.262-267
• /
• 2002

In this paper, we first studied the factors affecting the motor current (MC) signal, which was strongly affected by the systematic hardware noises depending on polishing such as pad conditioning and arm oscillation of platen and recipe, head motor. Next, we studied the end point detection (EPD) for the chemical mechanical polishing (CMP) process of shallow trench isolation (STI) with reverse moat structure. The MC signal showed a high amplitude peak in the fore part caused by the reverse meal. pattern. We also found that the EP could not be detected properly and reproducibly due to the pad conditioning effect, especially when conventional low selectivity slurry was used. Even when there was no pad conditioning effect, the EPD method could not be applied, since the measured end points were always the same due to the characteristics of the reverse moat structure with an open nitride layer.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.351-353
• /
• 2002

Up to now the design standard of tower for overhead transmission line in KEPCO was revised four times since 1970. During last year. we had reviewed this design standard. This paper shows the design standard of tower for overhead transmission line in KEPCO. In this standard, a kind of tower was defined as standard tower and special tower. Also we had defined usage range of standard tower, tower height, arrangement of power line, design condition of tower arm and etc. On the wind pressure, we had defined basic velocity pressure per region and maximum wind pressure. For special region, design wind pressure will be considered the receded wind velocity of meteorological observatory and regional condition by this standard.

• Clinical and Experimental Pediatrics
• /
• v.49 no.8
• /
• pp.821-829
• /
• 2006

Hemophilia is the most common coagulation disorder. It has a long history. Hemophilia A is caused by FVIII gene mutation, and hemophilia B by FIX gene mutation. Those genes are located on X chromosome long arm. Bleedings in hemophiliacs predominantly occur in joints and muscles. Because those site are insufficient in tissue factor to induce hemostasis. Among joints knee, ankle and elbow are most frequently affected because their synovial structure is vulnerable to injury compared to other joints. Hemophilia is diagnosed with factor assay. Severe hemophilia is below 1% of FVIII : C, moderate between 1% and 5%, mild over 5%. Carrier detection and prenatal diagnosis have been conducted with RFLP-based linkage analysis and DNA sequencing. Mainstay of treatment is factor replacement therapy so far. Bleedings can be controlled by infusion of factor concentrates. Hemophilc arthropathy and muscle contracture are representative sequelae. Complications of facotor replacement therapy are inhibitor development and infections. Hemophiliacs with inhibitor should be managed with large dose factor concentrate, bypassing agent, ITI and immunosuppression. Ultimately, hemophilia could be cured by gene therapy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.832-936
• /
• 1996

In this paper, we study a dynamic characteristics of HDD. HDD is constructed by spindle motor/disk unit, cover, base, E-block arm/suspension unit, and rotary actuator/voice coil motor. First, we make a FE model of spindle motor/disk unit and analyzed natural frequency/mode analytically and experimentally. Especially, the change of natural frequecy of spindle motor unit according to change of B.C is considered. Second, FE model of cover, base is made. Third, we assemble the above three FE mode, we get HEE assembly and dynamic analysis of HDD assembly is accomplished.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.66.1-66.1
• /
• 2010

Using two-dimensional numerical hydrodynamic simulations, we investigate the star formation rate (SFR) in turbulent, multiphase, galactic gaseous disks. Our simulation domain is axisymmetric, and local in the radial direction and global in the vertical direction. Our models include galactic rotation, vertical density stratification, self-gravity, radiative heating and cooling, and thermal conduction, but do not include spiral-arm features. Turbulence in our models is driven by momentum feedback from supernova explosion events occurring in localized dense regions formed by thermal and gravitational instabilities. Self-consistent radiative heating, representing enhanced/reduced FUV photons from the star formation, is also taken into account. By controlling three parameters (the gas surface density, the stellar disk density, and the angular rotation rate) that characterize local galactic disks, we explore how the SFR depends on the background environmental state. We also discuss the relation between the SFR and the gas surface density found in our numerical models in comparison with observations.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1999.04a
• /
• pp.105-107
• /
• 1999

본 연구의 목적은 CT장비로부터 얻어지는 단면 영상을 이용하여 재구성한 3차원 Voxel 정보를 기반으로 의료 시술 중 위험도가 높으며 장기간의 수술 훈련이 필요한 수술인 척추경나사 삽입술에 대한 모의 시술기를 개발하는 것이다. 모의 시술기의 입력은 환자의 환부에 대한 CT와 모의 시술을 해보고자 하는 의사 (사용자)의 입력 (경나사의 진입 위치와 각도)이 되며 출력은 의사들이 시술장에서 받을 수 있는 유일한 방법인 Voxel데이터로부터 재생성된 X-Ray이미지, 혹은 C-Arm의 동영상이며, 최종 결과 출력은 나사못이 삽입된 재구성 CT 이미지들과 3차원 정보를 볼 수 있는 Image Based Rendering의 Image data set이 된다. 본 연구에서는 각 시각화 부분의 특성을 고려하여 direct volume projection, surface modeling, 그리고 최근 많은 관심을 받고 있는 Image Based Rendering 기법을 intergrate하여 사용하였으며 각 시각화 모듈의 초고속 정보 통신망에서의 정보 교환에 대한 방법론에 대해 다루고 있다.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.159-164
• /
• 2000

In this study, the deformation analysis of 80mm optical disk holder considering the creep characteristics of plastic materials has been conducted and experimentally verified. It is very important to remedy the unrecoverable creep deformation and relaxation of holding force of an optical disk holder for the reliability of DVDR-P, DVD-ROM. A disk holder inserted in a cartridge case has been kept in the chamber with $60^{\circ}C$ temperature and 90% humidity for 24 hours. After storage test, the arm span and holding force of a disk holder have been measured after 24 hours at room temperature and normal humidity. The predicted results are in good agreement with experimentally measured one.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.454-456
• /
• 2002

Embedded system is used a lot in electric home appliances and home network equipment. However, this system is designed to operate by the system operator directly at home and operator could find out them only when he pays attention to the system in case event happens. In this paper, to improve above things, it designed to remote-control system anywhere in which internet access is possible as well as at home, and also it designed SMS(short message service) information transmission system to inform the errors to the operator when they happen. To design the system, development board(be included the Strong Arm), CDMA module, and electric door lock are used as hardware, and web browser, CGI(common gateway interface) programming, and C-language are used for implementation of software in embedded-linux platform.

• The Korean Journal of Pain
• /
• v.19 no.2
• /
• pp.253-256
• /
• 2006

Cervical disc herniation is one of the most common causes of neck, shoulder and arm pain. There are many treatments for a cervical disc herniation, such as rest, physical therapy, medication, epidural steroid injection and surgery. However, conservative treatments sometimes have limited effectiveness, and a surgical discectomy is often associated with numerous complications. Nowadays, a percutaneous discectomy, using a $Dekompressor^{(R)}$, has been used in herniated disc patients, but a posterolateral extruded disc is not an indication. Herein, our experience using a 19 G $Dekompressor^{(R)}$, on a 52 year-old male patient with a left C6-⁣7 posterolateral extruded disc, is reported. Decompression was successfully performed, and the pain and range of motion was immediately improved.