• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.525-530
• /
• 2001

As a part of efforts to examine feasibility of warm forging near-net-shape process for non-heat-treated steel to replace quenched and tempered S45C steel, the optimized process condition has been determined to be $820^{\circ}C$ for heating, 10/sec for strain rate of forging and approximately 250MPa for flow stress from observed results such as the $A_{3}$ transformation temperature of about $790^{\circ}C$, the fully dynamic recrystallized behavior between $800^{\circ}C\;and\;850^{\circ}C$ when compressed up to 63% engineering strain at 10/sec strain rate, and the high temperature microsturctural stability. Also, controlled cooling rate of $6.3^{\circ}C/sec$ by water-spraying at a rate of $0.10cc/sec-cm^{2}$ for 60seconds followed by air-cooling right after forging process has been considered in this study as a feasible approach based on examination of the microsturcture of mixed ${\alpha}-ferrite$ and pearlite, the hardness and tensile properties meeting specification, and the reduced total cooling time to room temperature. Successive works would be carried out for the impact strength, machinalility, and forgeability at this process in the near future.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.33-36
• /
• 2000

The dynamic recrystallization (DRX) of medium carbon steels (SCM 440 and POSMA45) was studied with torsion test in the temperature range of $900-1100^{\circ}C$ and the strain rate range of $5.0x10^{-2}\;-\;5.0x10^0/sec$. To establish the quantitative equations for DRX, the evolution of flow stress curve with strain was analyzed. The critical strain (${\varepsilon}_c$) and strain for maximum softening rate ( ${\varepsilon}^{*}$) could be confirmed by the analysis of work hardening rate ($d{\sigma}/d{\varepsilon}\;=\; \theta$). The volume fraction of dynamic recrystallization ($X_{DRX}$) as a function of processing variables, such as strain rate ( $\dot{\varepsilon}$ ), temperature (T), and strain ( $\varepsilon$ ) were established using the ${\varepsilon}_c$ and ${\varepsilon}^{*}$. For the exact prediction, the ${\varepsilon}_c$, ${\varepsilon}^{*}$ and Avrami' exponent (m') were quantitatively expressed by dimensionless parameter, Z/A respectively. The transformation-effective strain-temperature curve for DRX could be composed. It was found that the calculated results were agreed with the experimental data for the steels at any deformation conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.868-871
• /
• 2003

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability. Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of $1000^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using $SF_6/O_2$ and $CF_4/O_2$ gas mixture. Etch rate have been investigated as a function of oxygen concentration in the gas mixture, RF power, and working pressure. Etch rate was measured by surface profiler and FE-SEM. $SF_6/O_2$ gas mixture has been shown high etch rate than $CF_4/O_2$ gas mixture. Maximum etch rate appeared at 450W of RF power. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40%, and the superior anisotropic cross section was observed.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.947-952
• /
• 1996

The effect of fluctuating temperature on the respiration of vegetables has been investigated. Spinach was selected as the experimental material because of its high respiratory activity and kept under the condition that temperature changed alternately at low and high levels every 4 hours. The low-high level temperature combination was set in $1-10^{\circ}C,{\;}1-20^{\circ}C{\;}and{\;}1-30^{\circ}C$. Respiration was evaluated in terms of quantity of $CO_2$ evolved from spinach. The evolution rate of $CO_2$ was determined by a change in its concentration. The evaluation rate of $CO_2$ followed closely the temperature change. In the temperature combinations at $1-10^{\circ}C{\;}and{\;}1-20^{\circ}C$, the relationship between $CO_2$ evolution rate and temperature was found to be able to express by Arrhenius law, while at $1-30^{\circ}C$, it did not obey the law.

• Geomechanics and Engineering
• /
• 제5권1호
• /
• pp.57-70
• /
• 2013

Constant rate of strain (CRS) consolidation tests were conducted for undisturbed Ariake clay samples from three boreholes in Saga Plain of Kyushu Island, Japan. The coefficients of consolidation ($c_{\nu}$) were interpreted from the CRS test results by small- and large-strain theory. Large-strain theory was found to interpret smaller $c_{\nu}$ values and less strain rate effect on $c_{\nu}$ than that by small-strain theory. Comparing the theoretical strain distributions within a soil specimen to those obtained by numerical simulation shows that the small-strain theory can be used only for the dimensionless parameter $c_{\nu}/\dot{\varepsilon}H_0^2{\geq}50$ (where $\dot{\varepsilon}$ is strain rate and $H_0$ is the specimen height), and the large-strain theory can be used for a larger range of strain rates. Applying the criterion to undisturbed Ariake clay with a $c_{\nu}$ value of about $1{\times}10^{-7}\;m^2/s$, it is suggested that the large-strain theory should be adopted for calculating the $c_{\nu}$ value when $\dot{\varepsilon}$ > 0.03%/min.

• 설비공학논문집
• /
• 제11권4호
• /
• pp.492-498
• /
• 1999

Mass flow rates of R407C and R290 through capillary tubes were measured with various capillary tube geometries and flow conditions. For all refrigerants tested in the present study, mass flow rate through the capillary tube was strongly dependent on the condensing pressure, subcooling and capillary length and diameter. The flow rate of R407C was 5~10［%］ higher than that of R22 at the same condensing temperature and degree of subcooling, while flow rate for R290 was 40［%］ lower than that for R22. Based on experimental results, an empirical correlation was developed using Pi theorem to predict the mass flow rate through capillary tubes. The predicted flow rates using the model were consistent with the experimental data within ${\pm}$10[%］.

• 동력기계공학회지
• /
• 제10권2호
• /
• pp.111-116
• /
• 2006

Tribologcal property of the ceramics used in severe condition was investigated and both $Al_2O_3$ ball and Al/SiC composite made by thermal spray process[TSP] were used as a specimen in this study. Four kinds of material couple in ball and disk specimens were tested in the dry condition by using ball-on-disk type tribo-tester. Friction coefficient, surface roughness, wear rate, and photograph of the worn surface were investigated. Generally, High SiC contents[$40{\sim}50%$] specimens showed very low friction coefficient below 0.05 and little wear rate in dry condition. And also, low SiC contents[0%] specimens showed a moderate wear rate and high coefficient of friction at the same condition.

• 한국환경과학회지
• /
• 제17권8호
• /
• pp.919-924
• /
• 2008

The surface properties and adsorption rates of activated carbon modified with acid and base were compared. The distribution ratio of C and C-H on the surface of activated carbon were decreased by modification with acid and base, but the distribution ratio of C-O, C=O, and O=C-O were increased. Base modification damaged the surface of activated carbon more than acid modification, it caused the effect of 6 percent increments of surface area. Adsorption rate model was more suitable to second order equation than first order equation. Adsorption rate was controlled by adsorption in pore better than in surface.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제8권1호
• /
• pp.40-49
• /
• 2000

The capillary tube performance for R-407C is experimentally investigated. The experimental setup is a real vapor-compression refrigerating system. Mass flow rate is measured for various diameter and length while inlet pressure and degree of subcooling are changed. These data are compared with the results of a numerical model. The mass flow rate of the numerical model is about 14% less than the measured mass flow rate. It is found that mass flow rate and length for R-407C are less than those for R-22 under the same condition. Based on this experimental study and the numerical model, a set of design charts for capillary tube of R-407C is proposed.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 총회 및 춘계학술발표회
• /
• pp.73-76
• /
• 2002

Biofilter performance to reduce C $H_4$ emissions from MSW landfills was tested under a variety of environmental and design conditions. The optimum soil moisture content for C $H_4$ oxidation in a loamy sand was 13% by weight. The addition of N $O_3$-N did not affect the C $H_4$ oxidation rate. Soil depths of 30cm and 60cm were equally efficient in C $H_4$ oxidation. When the C $H_4$ loading rate was decreased, the percentage of C $H_4$ oxidized increased. The maximum C $H_4$ oxidation rate was 27.2 mol $m^{-2}$ $d^{-1}$ under optimum conditions (loamy sand soil, 13% moisture content, 30cm soil depth, and an loading rate of 32.8 mol $m^{-2}$ $d^{-1}$). Based on the above results, the installation of a properly sized and managed biofilter above a landfill cover should be capable of achieving a major reduction in atmospheric methane emissions from MSW landfills built with RCRA covers.