• Elastomers and Composites
• /
• 제46권3호
• /
• pp.218-222
• /
• 2011

본 연구에서는 반복적인 온도변화가 목분(50 wt.%와 70 wt.%)이 첨가된 폴리프로필렌 WPC(Wood Plastic Composites)의 기계적 특성에 미치는 영향을 조사하였다. WPC의 휨탄성계수(flexural modulus)와 휨강도 (flexural strength)는 반복 회수에 상관없이 동결 융해 시험에서 계면접착력의 약화 때문에 감소하는 경향을 보였다. 목분의 함량이 높을 때, 휨탄성계수의 감소가 비교적 높았다. WPC의 휨탄성계수와 휨강도는 고온($60^{\circ}C$) 저온 ($-20^{\circ}C$) 반복시험 후 고온에서 감소하고 저온에서 증가되었다. 폴리프로필렌(polypropylene, PP)의 유리전이점 (glass transition temperature: $-10^{\circ}C$) 보다 낮은 저온($-20^{\circ}C$에서 WPC는 높은 강성(stiffness)과 강도 (strength)를 유발시키는 유리상태(glassy state)로 존재한다. 고온에서 목분의 함량이 낮은 WPC가 연성의 증가 때문에 낮은 휨탄성계수와 휨강도를 보였다.

• 한국세라믹학회지
• /
• 제37권9호
• /
• pp.879-886
• /
• 2000

고온용 전기.열 절연재의 유리모재로 사용하기 위한 산화크롬함유 인산염 유리 복합체의 소결거동, 물성, 그리고 미세구조변화를 연구하였다. 단미의 유리는 점성유동에 의한 1단계 소결수축을 보이나 복합체는 점성유동 및 반응 액상소결에 의한 2단계 수축을 보였다. 단미 유리는 소결온도 증가에 따라 재기공율이 감소하고 기공크기가 작아지지만 93$0^{\circ}C$ 이사에서는 폐기공이 생성되면서 기공이 성장함을 보였다. 복합체 소결밀도는 산화크롬 증가에 따라 감소하였으며, 특히 산화크롬 40% 이상에서는 percolation에 의해 소결수축율이 급격히 저하하였다. 복합체의 곡강도는 산화크롬 증가에 따라 거의 직선적으로 감소한 반면 열팽창율은 오히려 급속히 증가함을 보였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.342-342
• /
• 2008

The low temperature sintering and microwave dielectric properties of ceramic/glass composites which were composed of ceramics in the $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ and zinc borosilicate glass/bismuth-zinc borosilicate glass were investigated with a view to applying the microwave dielectrics to low temperature co-fired ceramics. The $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ addition of 5 wt% ZBS and BZBS glass ensured a successful sintering below $900^{\circ}C$. In addition, pyrochlore phase was observed in the all composition. $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ with 5 wt% BZBS glasss demonstrated 70 as the dielectric constant ($\varepsilon_r$), 2,500 GHz as the Q$\times$f value, and -40 ppm/$^{\circ}C$ as TCF.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.326-330
• /
• 2004

Thermosetting matrix composites have disadvantages in terms of moulding time, repairability and manufacturing cost. Thus the high-performance thermoplastic composites to eliminate such disadvantages have been developed so far. As a result of environmental and economical concerns, there is a growing interest in the use of thermoplastic composites. However, since their mechanical properties are very sensitive to the environment such as moisture, temperature etc., those behaviors need to be studied. Particularly the temperature is a very important factor influencing the mechanical behavior of thermoplastic composites. The effect of temperature have not yet been fully quantified. Since engineering applications of reinforced composites necessitate their fracture mechanics characterization, work is in progress to investigate the fracture and related failure behavior. An approach which predicts the tensile strength was perpormed in the tensile test. The main goal of this work is to study the effect of temperature on the result of tensile test with respect to GF/PE composite. The tensile strength and failure mechanisms of GF/PE composites were investigated in the temperature range $60^{\circ}C\;to\;-50^{\circ}C$. The tensile strength increased as the fiber volume fraction ratio increased. The tensile strength showed the maximum at $-50^{\circ}C$, and it tended to decrease as the temperature increased from $-50^{\circ}C$. The major failure mechanisms was classified into the fiber matrix debonding, the fiber pull-out, the delamination and the matrix deformation.

• 수산해양기술연구
• /
• 제39권2호
• /
• pp.158-163
• /
• 2003

Thermosetting matrix composites have disadvantages in terms of moulding time, repairability and manufacturing cost. Thus the high-performance thermoplastic composites to eliminate such disadvantages have been developed so far. As a result of environmental and economical concerns, there is a growing interest in the use of thermoplastic composites. However, since their mechanical properties are very sensitive to the environment such as moisture, temperature etc., those behaviors need to be studied. Particularly the temperature is a very important factor influencing the mechanical behavior of thermoplastic composites. The effect of temperature have not yet been fully quantified. Since engineering applications of reinforced composites necessitate their fracture mechanic characterization, work is in progress to investigate the fracture and related failure behavior. An approach which predicts the tensile strength was perpormed in the tensile test. The main goal of this work is to study the effect of temperature on the result of tensile test with respect to GF/PE composite. The tensile strength and failure mechanisms of GF/PE composites were investigated in the temperature range 6$0^{\circ}C$ to -5$0^{\circ}C$. The tensile strength increased as the fiber volume fraction ratio increased. The tensile strength showed the maximum at -5$0^{\circ}C$, and it tended to decrease as the temperature increased from -5$0^{\circ}C$. The major failure mechanism was classified into the fiber matrix debonding, the fiber pull-out, the delamination and the matrix deformation.

• 한국세라믹학회지
• /
• 제42권12호
• /
• pp.842-845
• /
• 2005

Glass composites containing ceramic fiber have been developed for Solid Oxide Fuel Cell (SOFC) seals. Effect of glass type, loading pressure and thermal cycle the leak rates of composite seals was investigated. Seal performance of two commercial glasses was compared with that of $SiO_2BaO-B_2O_3$ glass synthesized in this work. The leak rate for seals made of pyrex(R) increases from $\~0.0005\;to\;\~0.004sccm/cm$ as the gas pressure increases from 10 to 50 kPa. The soda lime silicate glass seal shows the leak rate two times higher than the one made of pyrex(R) or $SiO_2BaO-B_2O_3$ glass. The viscosity of glass at the seal test temperature is presumed to affect the leak rate of the glass seal. As the applied loading pressure increases from 0.4 to 0.8 MPa at $750^{\circ}C$, the leak rate decreases from 0.038 to 0.024 sccm/cm for composite seals. It has been found that during 50 thermal cycles between $450^{\circ}C\;to\;700^{\circ}C$ leak rates remained almost constant, ranging from 0.025 to 0.03sccm/cm. The results showed an excellent thermal cycle stability as well as sealability of the glass matrix ceramic fiber composite seals.

• Elastomers and Composites
• /
• 제46권4호
• /
• pp.343-351
• /
• 2011

유기나노점토와 인화합물을 함유한 우레탄폼 복합체를 합성하고, 폼 생성속도, 밀도, 몰포로지, 열적특성 분석을 수행하였다. 우레탄폼 복합체는 Cloisite 30B가 박리/분산된 폴리아디페이트디올과 폴리에테르-폴리올(f=4.6), PMDI(f=2.5), D-580(phenyl polyoxyalkenyl phosphate)로부터 제조하였다. 발포제로써 cyclopentane과 증류수가 우레탄폼 복합체의 특성에 미치는 영향을 D-580의 농도 0~2.9 wt%에서 측정하였다. 증류수는 cyclopentane 보다 약 30% 빠르게 폼을 형성시켰다. 증류수로 발포한 우레탄폼 복합체의 밀도는 cyclopentane으로 발포한 경우보다 32~34% 낮았다. 증류수로 발포한 우레탄폼 복합체의 cell은 타원형인 반면에, cyclopentane으로 발포한 복합체는 구형의 형상이며, D-580의 함량이 증가함에 따라 cell 직경이 $158{\mu}m$에서 $100{\mu}m$로 감소하였다. Cyclopentane 으로 발포한 우레탄폼 복합체의 $T_g$는 D-580 함량이 증가함에 따라 $77.6^{\circ}C$에서 $56.1^{\circ}C$로 낮아졌다. 증류수로 발포한 우레탄 복합체의 $T_g$는 D-580 함량이 증가함에 따라 높아졌다. Cyclopentane과 증류수로 발포한 우레탄폼 복합체는 모두 $250^{\circ}C$에서 열분해가 시작하였다. Cyclopentane로 발포한 우레탄폼 복합체는 $500^{\circ}C$ 이상에서 열분해속도가 증가하는 2차 열분해 현상이 측정되었다. D-580에 의한 열안정성의 개선 정도는 cyclopentane으로 발포한 복합체에 비하여 증류수로 발포한 우레탄 복합체에서 더 높게 측정되었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권2호
• /
• pp.86-91
• /
• 1999

In order to analyse the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to the wavelength of ultraviolet rays and evaluated by comparing contact angle, surface resistivity, surface potential decay, and ESCA spectrum respectively. As irradiation energy are increased, the surface properties were steeply decreased in the range of 300[nm]. But the measured values within the scope of400[nm]∼440[nm] showed a increase as compared with the untreated ones. Also, fromthe result of ESCA spectrum, it was confirmed plenty of oxygen groups on the spot showing the maximum decrease of surface properties and the existence of ether groups on the surface of coloring phase. We can conclude that the degradation phenomena on the surface of epoxy composites are dominated by the induction of ester and carboxyl groups.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.513-517
• /
• 1997

Glass fiber reinforced thermoplastic composite materials have considerable promise for increased use in low cost high volum applications because of the potential for processing by solid phase forming. However, the forming characteristics of these materials have not been well known. The primary focus of this research is the investigation of the bendability of these composites and spring-back phenomena in pure bending. The materials tested contained 10, 35, and 40 percent by weight of randomly oriented glass fiber in a polypropylene matrix. The bending tests were performed at temperatures ranging form 75 ".deg. c" to 150 ".deg. c" and at punch speeds of 2.54 mm/sec and 0.0254 mm/sec. The measured bendability and spring back angle in pure bending werw compared with the predictions based on the simple analyical models. Goog agreement between experimental and analytical results was observed.esults was observed.

• 수산해양기술연구
• /
• 제39권3호
• /
• pp.167-173
• /
• 2003

Many of researches regarding mechanical properties of composite materials are associated with humid environment and temperature. Especially the temperature is a very important factor influencing the design of thermoplastic composites. However, the effect of temperature on impact behavior of reinforced composites have not yet been fully explored. An approach which predicts critical fracture toughness G$_{IC}$ was performed by the impact test in this work. The main goal of this work is to study the effect of temperature and span of specimen supports on the results of Charpy impact test for GF/PE composite. The critical fracture energy and failure mechanism of GF/PE composites were investigated in the temperature range of $60^{\circ}C;to;-50^{\circ}C$ by the Charpy impact test. The critical fracture energy showed the maximum at the ambient temperature, and it tended to decrease as the temperature increased or decreased from the ambient temperature. The major failure mechanisms are the fiber matrix debonding, the fiber pull-out and/or delamination and the matrix deformation.n.