• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.112-120
• /
• 2003

In this paper, dynamic track tension fur high mobility tracked vehicle is investigated by multibody dynamic simulation techniques. This research focuses on a heavy military tracked vehicle which has sophisticated suspension and rubber bushed rack systems. In order to obtain accurate dynamic track tension of track subsystems, each track link is modeled as a body which has six degrees of freedom. A compliant bushing element is used to connect track links. Various virtual proving ground models are developed to observe dynamic changes of the track tension. Numerical studies of the dynamic track tension are validated against the experimental measurements. The effects of pre-tensions, traction forces, fuming resistances, sprocket torques, ground profiles, and vehicle speeds, for dynamic responses of track tensions are explored, respectively.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.902-908
• /
• 2005

Various stresses (such as electrical stress, mechanical stress, environmental and electrochemical stress, and defects of structure) result in insulation degradation of epoxy mold type insulators. Since the insulation degradation of BCT(Bushing Current Transformer) and bushing proceeds during fabrication process or operation time due to these causes, various methods to reduce the degradation in their insulation ability have been suggested. In this paper, we investigated surface temperature increment of these insulators due to PD(partial discharge). After the voltage applied into the insulator to generate the artificial PD, the surface temperature of the insulator was measured with non-contact thermometer using infrared rays. It was confirmed through the analysis based on PD experiments that the procession in the insulation degradation of the insulator could be estimated through the measurement of the surface temperature in the insulator.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.163-166
• /
• 2003

Since the track pin is subjected to large transverse track tension from the track link, conventional track pins for high mobility vehicles are usually made of high strength steel, which increases the weight of tracked vehicles due to the high density of steel. In this paper, several composite materials were employed for track pin design to reduce weight of track pin as well as to enhance the fatigue life of rubber bushings. Especially the effects of shear stiffness of the composites on the life of rubber bushing were investigated.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.194-202
• /
• 2014

Steering axis of suspensions is an important factor that affects ride and handling quality in the vehicle chassis development. Macpherson strut and double wishbone's steering axis are defined geometrically, but multi-link suspensions can not be geometrically analyzed. In this case instant axis theory is commonly used to find a steering axis. Since the steering axis is moving with varying caster and kingpin inclination angle, this method approximately corresponds with exact solution. In this paper, we propose a velocity analysis method to find a pure rotational axis of the wheel relative to suspension arms, that is exact solution of the steering axis. This paper extends the method to analyze the steering axis of multi-link suspensions with bushing compliance. The analysis results applied to double wishbone and multi-link suspensions demonstrate validity and accuracy of the proposed method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.464-466
• /
• 2014

The mechanism synthesis methods, graphical, analytical and computer-aided technique have been proposed for selecting and scaling mechanical system. According to developing computation tools, mechanism could be synthesized much faster and more correct than previous analytical ways by improved techniques. In this paper, the improved synthesis method is proposed to solve body guidance synthesis problem. To perform the mechanism synthesis for body guidance, a planar linkage is modeled as a set of free three bushings located in design space. The values of bushing stiffness and x, y position of bushings yielding a desired functional requirement related to input motion are found by using an optimization technique.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.547-549
• /
• 2000

Silicone insulators have many advantages over porcelain insulators. Especially silicone insulators have good characteristics of impact hardness, surface insulation, ease of processing, mass productivity and don't have risk of bombardment and vandalism. Recently insulation part made by silicone are becoming widely used. In this paper we introduce the development of Sealing End for 132kV XLPE cable with silicone composite hollow insulator and the adoption of it to a actual transmission line in abroad. This paper contains of design procedure, structure, electrical performance of it.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.76-78
• /
• 2001

In this paper insulation cover that being used in distribution line have been evaluated for aging characteristics. For evaluating its aging properties, we dismounted a variety of samples, like insulation covers for termination of deadend clamp, bushing, LA, COS and sleeve, in the fields. we performed mechanical properties test, electrical test, weathering test, etc. of these samples. And these samples are compared with virgin sample. Test results shows the bad mechanical strength in some part of samples. Especially, Insulation covers for the bushing terminations have cracks in the surface of samples.

• 한국분무공학회지
• /
• 제12권1호
• /
• pp.38-44
• /
• 2007

Since the Liquid Phase LPG injection (LPLI) system has Advantages in power generation and emission characteristics compared to the mixer-type fuel-supply system, a variety of studies regarding LPLi system has been conducted and its applications are made in automobile industry. However, the heat extraction due to the evaporation of liquid fuel, causes not only a post-accumulation of fuel but also an icing phenomenon which is a frost of moisture in the air around the nozzle tip. Since there exists a difficulty in the accurate control of air fuel ratio in both fuel supply systems, it can result in poor engine performance and a large amount of harmful emissions. This research examines the characteristics of icing phenomenon and develops anti-icing bushing to prevent an icing on the surface of the injection tip. It was found that n-butane, which has a relatively high boiling point ($-0.5^{\circ}C$), was a main species of post-accumulation. Also the results show that the post-accumulation problem was allevaited the utilization of a large inner to outer bore ratio and smooth surface roughness. In addition, an icing phenomenon and its formation process were found to be mainly affected by the humidity and the temperature of inlet air in an inlet duct. Also, it was observed that an icing phenomenon is lessened using aluminum bushing whose end coincides with the end of fuel injection tip in length.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1320-1329
• /
• 1990

본 연구에서는 토크로드의 여러가지 성능시험이 하능한 시험기의 설계와 개발 에 관하여 논하려 한다. 토크 로드의 정적 성능은, 반경방향 스프링 특성시험 및 비 틀림 방향 스프링 특성시험 그리고 회전토크 특성시험 등을 통하여 평가된다. 그러 나, 이들 세가지 성능시험을 위한 시험기를 각각 개발할 경우 소요비용이 과다해진다. 따라서, 한정된 예산과 시험기 개발후 시험평가 공정의 간소화 등을 고려하여, 본 시 험기는 3대의 시험기로써 하여야 할 기능을 한대의 시험기로써 할수 있도록 개발하였 다. 시험기 개발에 따른 기술적인 고찰과, 본 시험기로 정하중에서의 토크 로드 부 품의 성능시험을 수행하고 서어보 유압식 구조물 피로 시험기를 사용하여 동 부품의 피로 내구성 시험을 실시하고, 고무의 조성변화, 접착성 개선 등을 통해 내구성을 향 상시킴으로 국산화 개발을 가능케 한 기술적 내용들을 살펴 보고자 한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.225-226
• /
• 2008