• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1780-1783
• /
• 2003

Burrs formed in micro drilling with Ø 1.0 and 0.5 are observed. The changes of burr geometry are compared when feed rate and velocity changes. Characteristics of burr formation in 4 different workpiece materials are analyzed. The coefficient of burr geometry, CB is introduced to classify burrs according to burr height and burr types. Finally control charts are produced using the coefficient of burr geometry and burr types in each workpiece material. Data base is constructed to be used for burr expert system.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.166-173
• /
• 2000

A system for burr measurement is developed to measure the geometry of the burr formed in metal cutting or shearing operations. laser system is selected according to the required measuring accuracy and burr size. A specific program for calculating the burr geometry from measured laser data is developed. The raw data is obtained by scanning cross the burr. The height and width of burr are calculated. Due to the specific characteristic of laser peak or valley are formed in measuring sharp edges or small sharp cracks. Compensation for the peak or valley is carried out to make it possible to calculate the burr, burr geometry is measured in 3 dimension.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.132-140
• /
• 2000

In conventional drilling, burr geometry can be changed according to the variation of drill geometry like point angle, rake angle. Step drilling is proposed to minimize the burr formation in drilling operation. The burr formed in first cutting can be removed in second cutting by the edge in step. The burr formed in second cutting by the edge in step can be minimized according to the change of geometry like, step angle and depth. The mechanism in step drilling is analyzed. Some step drills are applied to drilling the input shaft which is used for vehicle steering. To measure the burr formed in drilling, laser and height gage are used.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.485-491
• /
• 1999

A burr is formed in every corner of parts as a result of machining, which produces undesirable edge geometry and influence deeply to surface quality of workpiece. Therefore these burrs must be removed certainly. The cost of removing these burrs is directly proportional to their size. Burrs have been among the most troublesome obstruction to high productivity and automation of machining processes. The proper selection of cutting condition and tool geometry will be helpful to reduce the occurrence of burrs. In paper will observe burr formation along helix angle in end milling and certificate experimentally mechanics relation of helix angle and burr formation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.1043-1046
• /
• 2002

In this paper, drill tests were carried out by modifying drill geometry for burr minimization. Final objective of this study is to develop compatible drill shape for minimization of burr formation. These experimented results with modified drill are measured with laser sensor after performing drilling with variable material. Simultaneously, the cutting force and the torque of various drill geometry have been observed with same cutting condition to judge drill stability. As a result, burr was minimized in step drill with 75$^{\circ}$ step angle at every material.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.6
• /
• pp.81-87
• /
• 2003

Triangulation method, conoscopic holography method and interferometry method are analyzed for effective measurement of micro burr geometry, which is formed in micro drilling. To select proper sensor, the cross section of a cylinder with 0.5mm diameter is measured and the result shows that conoscopic holography method is effective for measuring highly inclined surface in cylinder. Burrs with 1.0mm and 30${\mu}{\textrm}{m}$ height are measured by three suggested methods. As a result, the conoscopic holography method is proved to be most proper in measuring burr geometry. Burr measurement system is developed, which consists of conoscopic laser sensor, X-Y table, controller and burr measurement program. Burrs can be measured automatically and the result is displayed in 3D shape

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.8
• /
• pp.65-72
• /
• 2004

For the burrs formed in machining are irregular and very sharp in shape, it is usually very difficult to measure burr accurately. It was proved that micro burr geometry can be measured imprecision by the Conoprobe sensor using conoscopic holography method. We developed 3D burr measurement system using this sensor. The system is composed of Conoprobe sensor, XY table, controller and 3D measurement program. Some measurements using the developed system are conducted for the burrs formed in micro drilling and piercing. Specific software fur burr measurement includes several function, calculation of burr volume, average burr height. Burs formed on a curved surface were compensated and measured successfully using the basic surface compensation function.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.407-410
• /
• 2002

Triangulation method, conoscopic holography method and interferometry method are analyzed for effective measurement of micro burr geometry, which is formed in micro drilling. To select proper sensor, cylinder with 0.5mm diameter is measured and the result shows that conoscopic holography method is effective for measuring highly inclined surface. Burr with 1.0mm height and 30$\mu\textrm{m}$ height are measured by all methods. The conoscopic holography method is probed to be most proper method for measuring micro burr. A Program for 3D display of measured burr is developed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.199-205
• /
• 2001

Burr makes troubles on manufacturing process due to deburring cost, quality of products and productivity. This paper described the results of experimental study on the influence of the cutting parameters on the formation of exit burrs in face milling. Using the results of experimental study, burr types are classified and data bases are developed to predict burr formation result. From the CAD file for work geometry and the NC data for tool path, the exit angles are calculated at every edges. This program predicts the burr geometry at exit edges using the prediction algorithm and data bases which are developed experimentally. Simulation results on deformation strain and temperature are also available in specific 2-dimensional cutting conditions. Also algorithm which can determine the exit angle is proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.911-914
• /
• 1997

This Experiment was carried out for bur minimization in drilling. New drill geometries are proposed to minimize the burr formation in drilling operation. Three types of drills are made, champer, round and step drill. The burr formed in first cutting by front cutting edge ca be removed in second cutting by the cutting edges in chamfer, round edge and step. New burrs are formed by second cutting and can be minimized according to the change of drill geometry like, chamfer size and angle, corner radius in round drill and step size and angle in step drill. To measure the burr formed in drilling, laser sensor is used.