• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.561-565
• /
• 2009

The performance of supersonic impulse turbine was investigated experimentally. Experiment was performed with the compressed air instead of the high temperature burned gas because of the limitation of test facility and danger. As a result of the experiment with the compressed air, the performance in the real gas(burned gas) was predicted by the similarity method. The nozzle area of prototype turbine was calculated based on the real gas. So, it is difficult to satisfy the similarity conditions completely. Two similarity conditions were set and the design point for real gas was existed between two similarity conditions. And, the new turbine test model with calculated nozzle area based on the compressed air was tested. Therefore, similarity point of the new turbine test model was also existed between above two similarity points. It means that the design point for real gas was similar to the test point with the new turbine model.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.4
• /
• pp.632-640
• /
• 2004

The purpose of this study is to clarify the influence of inert gas on the configuration characteristics of premixed turbulent propagating flames of hydrogen mixtures. Inert gas is changed to $N_2$, Ar, $CO_2$ and He keeping the laminar burning velocity of mixtures nearly the same value. A laser tomography technique was used to obtain the flame shape, and quantitative analyses were performed. The result shows that in the wrinkled laminar flame region, the surface area of turbulent flame is slightly dependent on the equivalence ratio and the kind of inert gas. It is also shown the region of convex part of flame toward the unburned gas is greater than that of toward the burned gas regardless of the kind of inert gas.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.629-634
• /
• 2010

Natural gas is a promising alternative fuel that can be used to satisfy the strict engine emission regulations in many countries. To develop natural-gas engines, low emission, efficient fuel consumption, and increased power ratings have to be realized. In this study, a cylindrical constant-volume combustion chamber (CVCC) was used to investigate natural-gas combustion characteristics for different prechamber design parameters and equivalence ratios. In particular, the maximum combustion pressure and mass fraction of the burned gas were evaluated by considering orifice diameter, volume ratio of prechamber and equivalence ratio. Using this result and by analyzing the changes in combustion characteristics with variations in design parameters, the optimum prechamber parameters were determined.

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.1-6
• /
• 2007

The purpose of this study was to investigate the reduction of exhaust gas temperature in a LPG engine that had been converted from a diesel engine. A conventional diesel engine was modified to a LPG (Liquefied Petroleum Gas) engine by replacing the diesel fuel injection pump with a LPG fuel system. The research was performed by measuring the exhaust gas temperature upon varying spark ignition timing, airfuel ratio, compression ratio, and different compositions of butane and propane. Engine power and exhaust temperature were not influenced by various butane/propane fuel compositions. Finally, among the parameters studied in this investigation, spark ignition timing is one of the most important in reducing exhaust gas temperature.

• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.143-149
• /
• 1999

The mounting technology of ceramic candle elements utilizing disk spring was tested in a hot bench unit. Seven SiC candle elements were fixed in three groups by 2, 2, and 3 elements per group. And its performance was investigated in a hot gas stream using oil burned-exhaust gas. The experimental results showed that this mounting method gave a good performance enough to be useful for the particulate removal in the integrated gasification combined cycle (IGCC). Some operational characteristics of the groupfilter were observed.

• Journal of the Korea Safety Management & Science
• /
• v.20 no.3
• /
• pp.21-26
• /
• 2018

This paper describes result of a study on safety against a fire of charging cable for mobile phone for vehicle. Combustion on the USB cable in the car was happened while driving. Gas coming from the burning USB cable could be a reason which can make a secondary car accident since the driver also can be embarrassed while driving. In order to prevent a secondary car accident connected on the road, to research a reason why USB cable can emit gas and be burned in charging. We did simulation test with abnormal fault condition for the electronic component on the board in the USB cable. So we get the result from abnormal fault condition simulation test, for instance, shorted test for output terminal of 8 pin switch, shorted test for chip resistor after thermal aging in the condition $25^{\circ}C$, 93 % RH during 48 hours. To analysis the result of all test, Combustion on the USB cable was not the 8 pin but other electrical component such as a chip resistor. Therefore we guess that the reason for USB cable combustion in charging in a car was not 8 pin and a LED but another defective component.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.508-516
• /
• 1989

The objective of this study is to investigate on the pulsating combustion of a granular coal in a Rijke type pulse combustor. The combustor is made of a 120cm long pipe with a honeycomb as a fire grate in the lower half. A fixed amount of coal is laid on the honeycomb and burned downward after ignition by using propane gas. Then the combustion driven acoustic oscillation occurs and makes the combustion pulsate with a very high amplitude. The effect of the pulsation and the air flow rate on the combustion characteristics is examined in comparison with the normal combustion. The non-pulsating combustion is made possible by placing absorbing material under the honeycomb. The combustion phenomena are observed visually, the burning time is measured in order to evaluate the combustion rate, and the variation of the gas temperatures is recorded. It is found that the fuel particle is greatly agitated like boiling by the flow pulsation and the burning-down velocity is so fast that the fuel is burned almost simultaneously. The combustion rate can be increased as twice as that of non-pulsating combustion with increase of the air flow rate. And the combustion becomes clean with less soot deposit and emission.

• Fire Science and Engineering
• /
• v.26 no.6
• /
• pp.7-14
• /
• 2012

This paper is to develop analytical techniques of flammable liquids which have been used for accelerating fire in accidental fires and arsons. We tested the temperature distribution of ceiling, fire patterns on the floor, and existence of flammable liquids and a check with GC/MS about flammable liquids comparing with papers, newspapers, and clothing. Research findings are as follows. The temperature of ceiling is influenced by flame. So gasoline and thinner was observed that combustible materials would be burned by flame. The fire patten on the floor was observed that flammable liquids had specialized pattern comparing combustible materials. When combustible materials on the PVC (Polyvinyl chloride) floor was burned, they didn't react to the gas detector. But flammable liquids had opposite results. After 7 days, we identified components of fire residues with the GC/MS (Gas Chromatography/Mass Spectrometry) about existence of flammable liquids and got components of flammable liquids. Fire investigation is a complicated processes. But we understand characteristics of materials, need detail investigations, and use the GC/MS to analyse flammable materials.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.3
• /
• pp.85-93
• /
• 1994

The engine performance and combustion characteristics of diesel oil and fish oil blended with diesel oils were investigated at various blending rate of fish oil in a diesel engine. The maximum pressure showed no significant difference among test fuels at low load, but it was higher as the blending rate of fish oil increases at high load. Increasing the blending rate of fish oil, the rate of heat release and burned fraction were higher than those of diesel oil. The ignition delay became longer than that of diesel oil as the blending rate of fish oil increases, and its differences were larger at different loads. The combustion duration and density of smoke were shorter and lower as the blending rate of fish oil increases. The rate of fuel consumption showed no significant difference between diesel oil and fish blended with diesel oils.

• Fire Science and Engineering
• /
• v.11 no.2
• /
• pp.19-24
• /
• 1997

numerical simulation of unsteady heat conduction equation were carried out by finite control volume method using the gas temperature derived from fire model as a boundary value. The reduction of compressive and flexural by heating were calculated from the temperature and the given reduction rate. It is shown that this method could be well applied to assess the safety of concrete column or beam of the burned building.