• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.908-910
• /
• 2004

Disabled people have benefited greatly from the developments in technology over the last twenty years. Systems have been developed and refined to help them overcome, or cope with, difficulties they experience as a result of their disabilities. As technology has become cheaper, more powerful and easier to use, disabled people have taken to using them to an ever increasing degree. In this paper, we propose novel hybrid mobility devices which use a combination of human power and electric power. This paper deals with the design of a direct-drive wheel Axial-flux permanent magnet motor. This type motor prove to be the best candidate for application in electric vehicles, as in comparison with conventional motors they allow design with higher compactness, lightness. A prototype vehicle for an application as a hybrid wheelchair is designed, built, and tested.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.6
• /
• pp.705-712
• /
• 2004

In this paper, detection of rotor position at standstill of toroidal switched reluctance motor(TSRM) with built-in search coils using neural network is proposed. When search coils are used as a position sensor, it has many advantages like low cost, decrease in the volume, high robust characteristics and wide applications. However, the initial rotor position detection is very difficult because the search coil's EMF doesn't exist at standstill. In this paper, detection of initial rotor position of TSRM with built-in search coils using neural network is suggested. The experiment for the proposed method are presented. As a result of that, the accuracy and validity of the proposed method is verified.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.35-41
• /
• 2007

In this paper a single-wheeled robot called GYROBO is built and its hardware is implemented. The single-wheeled robot is similar to a rolling disk relying on gyroscopic motions to maintain its balance. The GYROBO consists of three actuators: a spin motor a tilt motor, and a drive motor. The spin motor spins a flywheel at a high rate so that it provides the balancing stability to upright the robot. The tilt motor controls steering of the robot by gyroscopic effect. The drive motor makes forward accelerated motion to the robot. Several models are designed. Experimental works of the GYROBO to turn and move forward have been presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.382-386
• /
• 2002

The tapping is machining process that makes a female screw on the parts to be assembly together. It is used for the high-speed tapping machine with synchronizing function for the high productivity. This paper describes the development of the ultra high-speed tapping machine with 10,000rpm. The key factors in the tapping speed are the acceleration/deceleration velocity and the synchronizing errors between the spindle motor and feeding motor. To minimizing acceleration/deceleration time, the low inertia spindle with synchronous built-in servo motor is developed. To minimizing synchronizing errors, the tapping cycle algorithm under open architecture CNC environment is optimized. The developed tapping machine has 0.13sec/10,000rpm in acceleration/deceleration time and the synchronizing error below 4.0%. It has 0.55sec for cycle time of one female screw, M3 tap, 2 times depth of tap diameter.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.9
• /
• pp.827-835
• /
• 2015

In this paper, we present the implementation method of Dynamic Matrix Control(DMC) block for use with a Rapid Control Prototyping(RCP) system and consider the speed control of a DC motor using the developed DMC block. Firstly, we briefly introduce a lab-built RCP system. Secondly, we present a method for implementing a DMC block using C-language, which enables the DMC algorithm to be represented in a library block that can be used in a Simulink environment. Finally, we use the developed DMC block for the speed control of a DC motor, through which we show that the DMC-based control system can be easily implemented and applied to the real-time control of systems with relatively fast dynamics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.559-560
• /
• 2013

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.5
• /
• pp.577-584
• /
• 1999

In this paper, the double inverted pendulum having a single actuator is built and the controller for the system is proposed. The lower link of the target pendulum system is hinged on the plate to free for rotation in the specified range($10^{\cire}$) on the x-z plane. The upper link is connected to the lower link through a DC motor. The double inverted pendulum built can be kept upright posture by controlling the position of the upper link even though it has no actuator in lower hinge. The algorithm to control the inverted pendulum consists of a state feedback controller within a linearizable range and a fuzzy logic controller coupled with a nonlinear feedback compensator for the rest of the range. Conventional state feedback control is employed, and the fuzzy controller is responsible for generating the reference joint angle of the upper link for the nonlinear feedback compensator which drives a DC motor to generate an indirect torque to the lower joint. As a result, we can get the upright posture of the proposed pendulum system. Simulations and experiments are conducted to show the validity of the proposed controller.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.3
• /
• pp.83-88
• /
• 2014

FSI (Fluid Structure Interaction) method, in this study, has been applied to analyzing thermal characteristics of a high speed machine tool spindle system. The spindle is composed of angular contact ceramic ball bearings, a high speed built-in motor, a cooling jacket, and so on. The cooling jacket has three inlets and outlets. Using the FSI method, temperature distributions and thermal displacements of the spindle system were computed considering the heating of the front and rear bearings and the built-in motor. The results computed using the FSI method were compared with those determined by experiment and using the conventional numerical approach. The results determined using the FSI method were similar to those from the conventional numerical approach but showed better agreement with the experimental results. Therefore, it is concluded that the FSI method is useful for analyzing the thermal characteristics of high speed spindles and can be applied to the design of high speed spindles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.3
• /
• pp.261-267
• /
• 2009

The spindle with a built-in motor can be used to simplify the structure of machine tool system, while the rotor has unbalance mass inevitably. Therefore, it is important to recognize the effect of unbalance mass. This paper presents analysis of dynamic behavior of a high speed spindle with a built-in motor. The spindle is supported by the angular contact ball bearings and the rotor is fixed at the middle of spindle. The spindle used in CNC automatic lathe has been investigated using combined methodologies of finite elements and transfer matrices. The Houbolt method is used for the integration of the system equations and the dynamic behavior of spindle is obtained considering unbalance mass of rotor. Results show that increasing rotational speed of spindle magnifies the whirl responses of spindle seriously. Also the whirl responses of spindle are affected by the other factors such as unbalance mass and bearing stiffness.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.58-69
• /
• 2016

This paper describes the design and implementation of a new diode clamped multilevel inverter for variable frequency drive. The diode clamp multilevel inverter has been widely used for low power, high voltage applications due to its superior performance. However, it has some limitations such as increased number of switching devices and complex PWM control. In this paper, a new topology is proposed. New topology requires only (N-1) switching devices and (N-3) clamping diodes compared to existing topology. A modified APO-PWM control method is used to generate gate pulses for inverter. The proposed inverter topology is coupled with single phase induction motor and its performance is tested by MATLAB simulation. Finally, a prototype model has built and its performance is tested with single phase variable frequency drive.