• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.204-209
• /
• 2005

A small size broadband microstrip patch antenna with small ground plane has been fabricated using MEMS. Multiple layer substrates are used to realize small size and broadband characteristics. The microstrip patch is divided into 3 pieces and each patch is connected to each other using a metal microstrip line. The fabrication process is simple and only one mask is needed. Two types of microtrip antennas are fabricated. Type A is the micros trip antenna with metal lines and type B is the microstrip antenna without metal lines. The size of proposed microstip antenna is $8^{*}12^{*}2mm^{3}$ and the experimental results show that the antenna type A and type B have the bandwidth of 420 MHz at 5.3 GHz and 480 MHz at 5.66 GHz, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.770-775
• /
• 2004

Although $High-T_c $superconducting HTS antennas have high efficiency and high gain, narrow bandwidth due to the high Q is the major limitation for application of satellite communication and mobile communication. Defining bandwidth as the frequency range over which standing wave ratio (SWR) is 2:1 or less, HTS antenna bandwidths are typically less than 1 %. Thus considerable effort has been focused on developing HTS antennas for broadband operation. In this work the HTS antenna array, using the bipin antenna which consisted of two triangle-radiation patches, was designed and fabricated using a ${YBa}_2{Cu}_3{O}_7x (YBCO)$ superconducting thin film on a MgO substrate for broadband operation. Also gold antennas with the same dimension as our HTS antennas were fabricated on the MgO substrate for the comparison. Experimental results for both antennas were reported in terms of radiation patterns, return losses, bandwidths and other various characteristics. The center frequency of HTS antennas was 20.28 GHz and the bandwidth obtained was significant 10 %.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.47 no.3
• /
• pp.302-312
• /
• 2014

This article describes the design and performance characteristics of a broadband ultrasonic mosaic transducer. We focus on the improved bandwidth in the high frequency band of a previously designed broadband ultrasonic transducer (Lee et al., 2014). The improvement in the pulse-echo bandwidth was achieved by employing twelve $2{\times}2$ element subarrays, operating at different resonance frequencies, and utilizing the mosaic array concept. We found that the -6 dB and -12 dB bandwidths of the newly developed broadband ultrasonic mosaic transducer, were up to 155% and 170% of the previously designed model, with a quality factor of 1.71 and 1.25, respectively. The averaged TVR (transmitting voltage response), SRT (receiving sensitivity), and FOM (figure of merit) values in a nearly flat transmitting response band, from 45 to 105 kHz providing a -12 dB bandwith of 60 kHz, were 163.3 dB (re $1{\mu}Pa/V$ at 1 m), -192.8 dB (re $1V/{\mu}Pa$), and -30.9 dB, respectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.501-510
• /
• 2016

Capabilities of several beamforming techniques are compared for estimating the position of a moving source. Beamforming has enabled to widen our perspective of aeroacoustics in wind tunnel experiments and has provided useful approach in array measurements. Meanwhile beamforming techniques have been developed in a way to improve estimation accuracy and to save ing effort at the same time. In order to achieve reasonable outcome from aeroacoustic measurement, it is important to identify the spectral characteristics of source and to select an appropriate beamformer. Though aeroacoustic sources normally generates broadband noises, many array signal processing have been focused on narrowband processing which makes calculation numerically efficient. However, calculation in frequency-domain requires selection of single frequency of interest which affects spatial resolution and sidelobe level as a consequence. To be able to localize broadband noise source, it is proposed to use broadband beamforming. The formulas implements the deletion of diagonal term from cross spectral matrix. In this study, trajectory of flying source emitting broadband noise was simulated and several beamformers are applied.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.6
• /
• pp.247-252
• /
• 2003

In this paper, we have designed and fabricated a broadband 2-stage MMIC amplifier. Broadband characteristics could be obtained by compensated matching networks in a 2-stage amplifier design. This method is compensating low gains at lower frequencies in the 1st-stage with higher gains at lower frequencies in the 2nd- stage and then finally flat gains are obtained in the wide frequency ranges. Also, we have obtained not only broadband characteristics but also high gain using compensation matching network. The fabricated amplifier is measured by attaching on the test PCB(Printed Circuits Board). The measurement results are bandwidth of 1.1~2.8 GHz, S$_{21}$ gain of 11.1$\pm$0.3 ㏈ and P1㏈ of 12.6 ㏈m at 2.4 GHz.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.6
• /
• pp.31-37
• /
• 2008

In order to organize the Intelligent Transport System(ITS) as a communication equipment, the satellite and wireless system demand broadband characteristics for collecting information from the wide road. Band-pass filters (BPF) or broad BPFs used in such communication system are required for broadband characteristics. This paper presents a design of such broad BPF which can be used in the system. Designed BPF which was difficult to get broadband characteristics after realization, become possible to realize filter with broad bandwidth and compact structure using parallel coupled line. The designed filter achieved the insertion losses improved by 0.4 dB and the return losses improved by 17.4 dB respectively with 60% of bandwidth at the 5.8 GHz of the center frequency, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1097-1106
• /
• 2009

In this paper, the cross monopole antenna with branch element is presented and its radiation characteristics are investigated. To confirm the broadband characteristics of the proposed antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in PCS, WCDMA, WiBro and S-DMB band(1.750~2.655 GHz). It is shown that the designed antenna has the non-directional pattern in the horizontal plane, the directional pattern in the vertical plane, VSWR less than 1.5 and gain over 1.9 dBi in 1.72~2.82 GHz. From these results, the presented antenna is conformed as a broadband antenna which can be used for PCS, WCDMA, WiBro and S-DMB band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.1
• /
• pp.26-35
• /
• 1996

In this paper, characteristics of the electromagnetically coupled broadband microstrip antennas are analyzed by the Finite Difference Time Domain (FDTD) method, and antenna para- meters are optimized to get maximum bnadwidth. By using short radial tuning stub in microstrip feedline, electromagnetically coupled microstrip antenna shows broadband ($\simeq$13%) characteristics, and the characteristics are varied as a function of radius, radial angle, and position of the radial tuning stub. Operating frequency, return loss, VSWR and input impedance are calculated by Fourier transforming the time domain results. After optimization of the parameters, maximum bandwidth of the radial stub tuning microstrip antenna is about 15% and the ripple char- acteristic of the VSWR is better than the rectangular tuning stub microstrip antenna.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.1
• /
• pp.17-27
• /
• 1995

In this paper, Finite Difference Time Domain (FDTD) method is used to analyze characteristics of the electromagnetically coupled broadband microstrip antenna, and to optimize the antenna parameters. By using short tuning stub in feedline, electromagnetically coupled microstrip antenna shows broadband (approximatcly equal 13%) characteristics, and the characteristics are varied as a function of length, width, and position of the tuning stub. Operating frequency, return loss, VSWR and input impedance are calculated by Fourier transforming the time domain results. Measurement data from fabricated electromagnetically coupled microstrip antenna are compared with FDTD results and are shown to be in good agreement. After optimization of the parameters, maximum bandwidth of about 15% is achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1233-1239
• /
• 2008

In this paper we proposed a novel broadband printed monopole antenna for PCS/IMT-2000/WLAN terminals by widening current flow To compensate narrow bandwidth characteristics which is one of disadvantages of general printed monopole antenna, we add the patch of diamond shape and induce the current in various directions for acquiring broadband characteristics. And frequency characteristics is optimized with Various design parameters. The bandwidth of the realized antenna is $1.66{\sim}3.04\;GHz$(58.72 %) below the return loss of -10 dB which contain the required band-width of PCS/IMT-2000/WLAN band.