• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.241-244
• /
• 2003

The world largest 21.3" LTPS LCD has been successfully developed using SLS crystallization technology. Successful integration of gate circuit, transmission gate and level shifter was performed in a large area uniformly. Uniformity and high performance from high quality grains of SLS technology make it possible to come true a uniform large size LTPS TFT-LCD with half number of data driver IC's used in typical a-Si LCD. High aperture ratio of 65% was obtained using an organic inter insulating method, which lead a high brightness of 500cd/cm2.

• 소성∙가공
• /
• 제17권5호
• /
• pp.322-327
• /
• 2008

LGP is a key component of LCD back light unit because it determines brightness and sharpness of the display image. Usually, it has optical patterns fabricated on the bottom surface. These optical patterns convert point or line sources placed in the side of LGP to plane source at the top surface by changing the propagating direction of the incident light. In the present paper the LiGA-reflow method was applied to fabricate the LGP mold. Furthermore, the optical simulation considering the replication ratio of pattern height was applied to the pattern design. The optical simulation through systematic correction scheme was adopted to find the optimum distribution of pattern density. Finally, the stamper fabricated by this method was installed in the mold and LGP was produced by injection molding. As a result of luminance measurement for the final product, the average luminance and luminance uniformity was measured 3,180 nit and 84%, respectively. Consequently, the mold fabrication method using the LiGA-reflow and optical simulation(CAE) can save the expense and time compared with the existing fabrication methods(laser ablation and chemical etching).

• 천문학회지
• /
• 제40권4호
• /
• pp.131-132
• /
• 2007

The research of OH maser emission sources with high angular resolution is complicated by the effects of interstellar scattering: more over, most of the OH maser sources are located in the galactic plane where the scattering is largest. However, the data available from pulsar studies on the spatial distribution of the amount of scattering indicate that there is a strong non-uniformity in the distribution of the amount of scattering material. There are directions in the galactic plane where the scattering is an order of magnitude higher than the average, as well as directions where the scattering is much lower. The latter provide an opportunity to investigate OH masers with the full angular resolution offered by very long baseline interferometry instruments, like the VLBA, and measure their true angular size, shape and brightness temperature. We have observed approximately 100 OH maser sources, distributed all over the northern hemisphere, with the VLBA in order to study the scattering properties of the interstellar medium.

• 대한기계학회논문집A
• /
• 제33권8호
• /
• pp.720-725
• /
• 2009

Among many kinds of parts for Liquid Crystal Display (LCD), a Back Light Unit (BLU) that changes the path of the light from light source to screen is the most important part to improve optical performances such as uniformity and average value of brightness. Up to recently, design process of BLU has been carried out by depending on the experience of design engineer. Using this approach, however, is proven that it is hard to effectively deal with difficulties in a process of the LCD development such as frequent design modifications, various design requirements, and short-term development. To cope with this situation, we applied a Process Integration and Design Optimization (PIDO) based design environment. PIDO is a software package to integrate multiple simulation processes and find a better solution using various design techniques. In this research, we found a design solution satisfying all design requirements by using the PIDO.

• Journal of Power Electronics
• /
• 제9권2호
• /
• pp.164-172
• /
• 2009

Recently, 2-dimensional flat light sources have been attracting much attention for its use in LCD backlight applications because of its high luminous efficiency and uniformity. A long-gap discharge, mercury-tree flat fluorescent lamp has been developed, which shows a high brightness ($>5000\;cd/m^2$) and high luminous efficacy (60 lm/W). Additionally, it has a wide operating margin and stable driving condition with the aid of an auxiliary electrode. For driving the lamp, a narrow pulse power to maintain the glow discharge state is required. Since there has been no research for this kind of lamp driving, this paper proposes a newly developed short-pulse, high-voltage lamp-driving scheme. The proposed lamp system uses a ballast with a coupled-inductor in order to raise the short pulse voltage up to the lamp ignition level and to obtain energy-recovery action during the glow discharge mode. The operation principles are presented and also the system performances such as the lighting efficiency, spatial and angular uniformities are evaluated by hardware experiments. The results show that the proposed lighting system is a good candidate for the next-generation of LCD backlight systems.

• 한국전기전자재료학회논문지
• /
• 제28권2호
• /
• pp.131-136
• /
• 2015

We develop the 60 W class hybrid solar LED street lamp controller. The controller is providing power via an inverter in the day with the least solar cell and battery and charging the battery for the ESS, acts as a power failure, the built-in battery. Rated output of the fabricated LED street lamp is 300 W or greater battery capacity 300 Wh, discharge time 10 hr, LED street lamp efficiency showed a very high level of light efficiency by about 127 lm/W. In addition, as a result of light distribution pattern according to the distance and the light intensity measurement will be able to ensure a very high quality, show the constant brightness in the distance from the road lights 6 m is about 35~40 lux in uniformity ratio. The proposed hybrid solar LED street lamp system showed a high energy capacity of approximately 1.5 to 152.7% power generation efficiency than typical conventional solar street lamp.

• Computers and Concrete
• /
• 제10권4호
• /
• pp.409-417
• /
• 2012

The quality of high performance concrete largely depends on water cement ratio, porosity, material composition and mix methods. The uniformity of color, texture and compressive strengths are quality indicators commonly used to assess the overall characteristics of concrete mixes. The homogeneity and share of coarse aggregates play a key role in concrete quality and must be analyzed in a microscopic point of view. This research studies the quality of high performance concrete by taking drilled cores in both horizontal and vertical directions from a 1.0 $m^3$ specimen. The coarse aggregate, expressed in digitized $100{\times}116$ dpi resolution images are processed based on brightness in colors through commercial software converted into text files. With the image converting to text format, the share of coarse aggregate is quantified leading to a satisfactory assessment of homogeneity - a quality index of high performance concrete. The compressive strengths of concrete and the shares of coarse aggregate of the samples are also compared in this research study to illustrate its correlation in concrete quality. It is concluded that a higher homogeneity of aggregate exists in the vertical plane than that of the horizontal planes of the high performance concrete. In addition, the concrete specimen showing denser particle packing has relatively higher compressive strengths. The research methodology provides an easy-to-use, direct measurement of high performance concrete when conducting quality assessment in the construction site.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.269-272
• /
• 2008

LGP is a key component of LCD back light unit because it determines the brightness and sharpness of display image. Usually, it has optical patterns fabricated on the bottom surface. In the present paper the LiGA-reflow method was applied to fabricate the LGP mold. Furthermore, the optical simulation considering the replication ratio of pattern height was applied to the pattern design. The optical simulation through systematic correction scheme helped find the optimum distribution of pattern density. Finally, the stamper fabricated by this method was installed in the mold and LGP was produced by injection molding. As a result of luminance measurement for the final product, the average luminance and luminance uniformity was measured 3,180 nit and 84%, respectively. Consequently, the mold fabrication method using the LiGA-reflow and optical simulation(CAE) can save the expense and time compared with the existing fabrication methods(laser ablation and chemical etching).

• 한국정보통신학회논문지
• /
• 제12권6호
• /
• pp.1051-1055
• /
• 2008

ZnS는 전기적 에너지를 받으면 전자와 정공이 무수히 발생하며 이들이 평형상태로 갈 때 보다 높은 준위로 여기되면 빛이 생성될 수 있다. 박막 ELD는 탁월한 시각효과, 고체상태 및 제조의 용이성 등의 장점을 갖고 있으나 발광세기의 향상, 소모전력의 감소, 구동전압의 저하 등 해결되어야 할 문제점이 많이 남아있다. 이러한 문제점을 해결하기 위하여 보다 우수한 박막EL의 전계발광(EL)표시장치를 설계 제작하였다. 우수한 재료선택을 위하여 일본의 High purity사의 제품을 선택하였고, 이 제품이 Electron Beam으로 증착 시에 우수한 특성을 나타냈고, 휘도도 상용화된 800fL에 80% 수준으로 제작과정을 개선하여 더욱 우수한 결과를 얻을 수 있고 본 연구는 Yellow의 경우 650fL의 휘도를 얻었고, Green의 경우 350fL의 휘도를 얻었다. Electron Beam 제작용으로 자체 제작된 기판 홀더로 막을 제작한 결과 두께 균일도는 6% 내외 의 결과로 상당히 우수한 특성을 나타내었다.

• Journal of Information Display
• /
• 제2권3호
• /
• pp.48-53
• /
• 2001

Carbon nanotube emitters, prepared by screen printing, have demonstrated a great potential towards low-cost, largearea field emission displays. Carbon nanotube paste, essential to the screen printing technology, was formulated to exhibit low threshold electric fields as well as an emission uniformity over a large area. Two different types of triode structures, normal gate and undergate, have been investigated, leading us to the optimal structure designing. These carbon nanotube FEDs demonstrated color separation and high brightness over 300 $cd/m^2$ at a video-speed operation of moving images. Our recent developments are discussed in details.