• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.414-421
• /
• 1999

In this paper, the simplified method for 2-dimensional train/track/bridge interaction analysis is utilized in the analysis of dynamic behavior of bridges in which the eccentricity of axle loads and the effect of the toriosnal forces acting on the bridge are included for the more accurate train/track/bridge interaction analysis. Inverstigations mainly into the influence of vehicle speed on train/track/bridge interactions are carried out for the two cases. The first case is that only train and bridge are considered in the modelling and the other case is that train, track and bridge are considered.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1028-1033
• /
• 2004

The open deck steel bridge is the most common type in railway bridges. Steel I-shaped girders are connected with sleepers directly without ballast and moving train loads are transmitted directly to the girder, so this bridge has weak characteristics on impact. Therefore, considerable accelerations can cause unsatisfactory dynamic behavior of the open deck steel bridge. Especially, Impact created at rail joints can increase the dynamic response of the bridge and this phenomenon would be injurious to passenger comfort. In the present study, dynamic behavior of the open deck steel bridge which has a rail joint is estimated through experimental studies and bridge-train interaction analysis considering surface irregularities by rail joints.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.10a
• /
• pp.251-258
• /
• 1999

The vibration control of bridge is studied considering the vibration characteristics of the Korean-type high-speed railway bridge. Fast nonlinear analysis is adopted as time integration method and the bridge and the train are modeled by FEM and sequentially moving constant forces respectively. Additional damping mechanism is indispensable to the Korean-type high-speed railway bridge because resonance vibration is excited under the maximum design speed. The optimal position and capacity of the damper is studied through the parametric studies, Transient vibration of the bridge is effectively controlled by such additional dampers which means that dampers play a role as structural damping. And also the maximum response of the bridge is reduced. Therefore it is verified that the increase of expected service life and the improvement of serviceability can be obtained through dampers.

• Structural Engineering and Mechanics
• /
• v.78 no.2
• /
• pp.163-174
• /
• 2021

Track-bridge interaction has become an essential part in the design of bridges and rails in terms of modern railways. As a unique ballastless slab track, the longitudinal continuous slab track (LCST) or referred to as the China railway track system Type-II (CRTS II) slab track, demonstrates a complex force mechanism. Therefore, a comprehensive track-bridge interaction study between multi-span simply supported beam bridges and the LCST is presented in this work. In specific, we have developed an integrated finite element model to investigate the overall interaction effects of the LCST-bridge system subjected to the actions of temperature changes, traffic loads, and braking forces. In that place, the deformation patterns of the track and bridge, and the distributions of longitudinal forces and the interfacial shear stress are studied. Our results show that the additional rail stress has been reduced under various loads and the rail's deformation has become much smoother after the transition of the two continuous structural layers of the LCST. However, the influence of the temperature difference of bridges is significant and cannot be ignored as this action can bend the bridge like the traffic load. The uniform temperature change causes the tensile stress of the concrete track structure and further induce cracks in them. Additionally, the influences of the friction coefficient of the sliding layer and the interfacial bond characteristics on the LCST's performance are discussed. The systematic study presented in this work may have some potential impacts on the understanding of the overall mechanical behavior of the LCST-bridge system.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.396-401
• /
• 2003

For a realistic and reasonable determination of condition and status, assessment system should include load modeling for the loads acting on slab bridges due to traffic loads, evaluation system for fatigue, and determination of remaining service life. The purpose of the present study is to develop a realistic expert system which can estimate reasonably the fatigue and service life of slab bridges, based on the load models that are derived from the traffic loads.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.239-241
• /
• 2005

Reliability analysis of the design of reinforced concrete rahmen bridge is performed. Statistical properties for loads and resistances are taken into account in the analysis and the reliability indices are calculated for strength limit state of the current bridge design specification. Results are presented and discussed for different span lengths and wall heights.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.701-704
• /
• 2000

Considerable research has been done to study the fatigue behavior of reinforced concrete bridge deck which is strengthened by carbon fiber sheets. Before the strengthening, the specimen was damaged by repeated loads with various repeat cycles. The results of this study show that strengthening efficiency is getting rised in the lower pre-damaged degree. When the fatigue damaged bridge-deck is strengthened, the crack propagation may be controled efficiently

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.187-194
• /
• 2003

This paper presents an energy method for the analysis of the in-plane ultimate load capacity of cable-stayed bridges considering deck and pylon connection. The potential energy of the whole bridge, including bridge deck, stayed cables, and pylons, and the work done by external loads are considered in the development of the bridge energy equation. Both geometric and material nonlinearities are taken into account in the analysis. The method is simple to use and has a high convergence rate.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.307-314
• /
• 1998

A novel high power factor Dual Half Bridge Series Resonant Inverter (DHB-SRI) for an induction heating appliance with multiple loads is proposed to remove the interferential acoustic noise caused by the difference between operating frequencies of adjacent loads. The circuit enables independent full power range control of two induction heating elements by one inverter circuit and has minimum switching losses due to the zero voltage switching characteristic. According to the mode analysis, I will explain the operation of the proposed circuit. To evaluate the required cooling capacity, loss analysis is performed through deriving some loss equations. In order to obtain the power factor correction capability and to lessen the system size, suitable design guides are given. Using the designed values, the proto-type circuit with 2.8kW power consumption for each induction heating element is built and tested to verify the operation of the proposed circuit.

• International Journal of Highway Engineering
• /
• v.17 no.6
• /
• pp.37-45
• /
• 2015

PURPOSES : The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridge-type concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads. METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results. RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual-wheel loading condition by accelerating pavement tester. CONCLUSIONS : Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.