• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.402-409
• /
• 2015

In this study a quasi-dimensional model is developed to predict the combustion process and emissions of a GDI engine under ultra-lean conditions. Combustion of a GDI engine condition is modeled as two simultaneous processes to consider significant fuel stratification. The first process is premixed flame propagation described as burning in a hemispherically propagating flame. The second is diffusion-controlled combustion modeled as mixing of multiple spray zones in the burned gas region. Mixing is an important factor in ultra-lean conditions leaving stratified mixture of developing sprays behind the propagating premixed flame. Sheet breakup and Hiroyasu models are applied to predict the velocity of a hollow cone spray. Validation is performed against measured pressures and NOx and CO emissions at different load and rpm conditions in the test engine.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.9
• /
• pp.817-824
• /
• 2010

An improved spray model of a pressure-swirl atomizer was developed and the grid dependency of the model was investigated. Since the Lagrangian-Eulerian approach was adopted for tracking droplets, very small grids could not be used. However, in order to detect swirl flow accurately, small grids were needed because of the consideration of swirl injection. In order to overcome these limitations, numerical studies were performed by using various grids with cell sizes ranging from 10.0 $\times$ 10 mm to 0.625 $\times$ 0.625 mm. From these calculated results, it was observed that the most efficient grid cell size was 1.25 $\times$ 1.25 mm.

• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.133-138
• /
• 2002

A 3-D axisymmetric computer program is developed to predict the NO behavior in SNCR system for the stoker incinerator with the waste treatment capacity, 200ton/day. To this end a turbulent reacting flow field calculation is made using proper assumption and empiricism. The stoker bed is assumed to be a homogeneous waste-volatilized gaseous state. The initial composition or reactants are assumed based on the data of the ultimate analysis. Turbulent is resolved by k-e model and turbulent reaction is handled by eddy-breakup model harmonized with empirical chemistry data for gaseous combustion, NO and urea reaction. The liquid droplet is traced by Lagrangian method incorporated by aerodynamic drag, Coriolis and crntrifugal forces. Radiation is treated by sensible heat loss model. Calculation results are in good agreement with experimental data at the outlet of post combustion chamber in Daejon 4th industrial complex. The flue gas shows the temperature range of $900\sim1000^{\circ}C$, velocity of 5m/s and NO concentration of 140ppm at the exit while the measured temperature, flue gas velocity and NO concentration are $967^{\circ}C$, $3\sim4m/s$ and $100\sim200ppm$respectively. Using the developed computer program a parametric study has been made with the variation of heat content of waste, castable length and SNCR variables for the determination of proper injector location. In general, the calculated results are consistent and physically acceptable.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.645-652
• /
• 2010

The aim of this investigation was study on the non-evaporation diesel spray characteristics injected through a common-rail diesel injector under various ambient pressure. The diesel spray was investigated with observation of macroscopic characteristics such as spray tip penetration and spray cone angle by the shadowgraph and the image processing method. The numerical study was conducted using a computational fluid dynamics code, AVL-FIRE. The breakup models used were WAVE model and standard $k-{\varepsilon}$ turbulence model was applied. The numerical study used input data which spray cone angle and fuel injection rate was achieved by Zeuch's method. Comparison with experimental result such as spray tip penetration was good agreement. Distribution of droplet diameter were conducted on four planes where the axial distances were 5, 15, 39 and 49mm respectively downstream from the orifice exit.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.54-58
• /
• 2005

The hydrolytic behavior of microbial poly[(R)-3-hydroxybutyrate]](P(3HB)) has been studied by using two model systems, Langmuir monolayer and solution-grown single crystals (SCs), for elucidating the mechanism for both alkaline and enzymatic degradations. An initial degradation of SCs of P(3HB) leads to breakup lamellae parallel to their short axis (b-axis). Similarly, ridge formation on the lamellar surface appears along the b-axis at lower quenching temperature than melting temperature. Both results support that the lamellar crystals contain less-ordered and more thermally sensitive regions along the b-axis. Although the enzymatic hydrolysis of P(3HB) monolayers was similar to its alkaline one, the enzymatic degradation of P(3HB) monolayers occurred at higher constant surface pressure than the alkaline degradation. This behavior might be attributed to the size of enzymes which is much larger than that of alkaline ions; that is, the enzymes need larger contact area with monolayers to be activated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2386-2396
• /
• 1996

A numerical simulation has been performed for isothermal and reacting flows in an exisymmetric, bluff-body research combustor. The present formulation is based on the density-weighted averaged Navier-Stokes equations together with a k-epsilon. turbulence model and a modified eddy-breakup combustion model. The PISO algorithm is employed for solution of thel Navier-Stokes system. Comparison between measurements and predictions are made for a centerline axial velocities, location of stagnation points, strength of recirculation zone, and temperature profile. Even though the numerical simulation gives acceptable agreement with experimental data in many respects, the present model is defictient in predicting the recoveryt rate of a central near-wake region, the non-isotropic turbulence effects, and variation of turbulent Schmidt number. Several possible explanations for these discrepancies have been discussed.

• 한국전산유체공학회:학술대회논문집
• /
• 1996.05a
• /
• pp.58-67
• /
• 1996

This paper describes some computational results of various energy and environmental systems using Patankar's SIMPLE method. The specific topics handled in this study are jet bubbling reactor for flue gas desulfurization, cyclone-type afterburner for incineration, 200m tall stack for 500 MW electric power generation, double skin and heat storage systems of building energy saving for the utilization of solar heating, finally turbulent combustion systems with liquid droplet or pulverized coal particle. A control-volume based finite-difference method with the power-law scheme is employed for discretization. The pressure-velocity coupling is resolved by the use of the revised version of SIMPLE, that is, SIMPLEC. Reynolds stresses are closed using the standard $k-{\varepsilon}$ and RNG $k-{\varepsilon}$ models. Two-phase turbulent combustion of liquid drop or pulverized coal particle is modeled using locally-homogeneous, gas-phase, eddy breakup model. However simple approximate models are incorporated for the modeling of the second phase slip and retardation of ignition without consideration of any detailed particle behavior. Some important results are presented and discussed in a brief note. Especially, in order to make uniform exit flow for the jet bubbling reactor, a well-designed structure of distributor is needed. Further, the aspect ratio in the double skin system appears to be one of important factors to give rise to the visible change of the induced air flow rate. The computational tool employed in this study, in general, appears as a viable method for the design of various engineering system of interest.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.288-288
• /
• 2018

점착성 유사는 응집 현상을 겪는 유사로, 응집 현상(Flocculation Process)는 응집 과정(Aggregation Process)와 파괴 과정(Breakup Process)의 경쟁으로 이루어진다고 여겨진다. 응집 현상을 통해 점착성 유사는 물과 점착성을 띠는 작은 입자들의 덩어리인 플럭(Floc)을 형성하여 흐름 내에서는 대부분이 플럭의 형태로 이동한다. 점착성 유사의 응집 모형 중 하나인 플럭 성장모형(Floc Growth Model, FGM)은 상미분 방정식으로 시간에 따른 플럭의 크기를 계산하는 모형이다. 응집과 파괴의 평형 상태에서 평균 입경을 얻는다. 이러한 FGM은 낮은 수치 계산 비용으로 합리적인 계산 결과를 얻을 수 있으며, 유사 이동 모형 혹은 흐름 모형과의 결합이 수월한 장점을 가진다. 또한, 닫힌 계(Closed System)에서 질량이 보존되는 특징이 있다. 반면, 결정론적인 특성을 띠면서 특정 플럭 크기만을 계산하기 때문에 점착성 유사의 입도 분포에 대한 정보를 얻을 수 없다. 결정론적 특성을 띠는 FGM에 추계학적 방법을 적용함으로써 특정 확률 분포형을 가지는 플럭의 입도 분포를 얻을 수 있다. 본 연구에서는 기 개발된 추계학적 FGM과 유사 이동 모형의 결합을 통해 변화하는 유수동역학적 조건에서 플럭의 입도 분포를 산정하고자 한다. 이전의 많은 실험실 실험 결과들은 부유가 발생한 상태를 유지하면서 수행되는 것으로, 특정 난류 특성(난류 소산 매개변수)와 특정 유사 농도 조건에서의 입도 분포를 얻는다. 그러나 하구부 및 하천의 하류는 조류의 영향을 받는 구간으로, 점착성 유사의 특성을 분석하기 위해서는 변화하는 유수동역학적 특성에 관한 고려가 필수적이라 할 수 있다. 결합된 점착성 유사 입도 분포 모형은 플럭의 침강과 재부유를 고려할 수 있는 특징을 가지며, 실측자료와의 비교를 통해 입도 분포를 합리적으로 모의하는 것으로 나타난다. 본 연구에서 개발된 점착성 유사 입도 분포 모형은 나아가 비점착성 유사의 입도 분포 모형과의 결합을 통해 두 종류의 유사가 혼재하는 구간에서도 합리적인 입도분포와 유사의 이동을 모의할 수 있을 것으로 예측된다.

• The KIPS Transactions:PartD
• /
• v.13D no.4 s.107
• /
• pp.557-564
• /
• 2006

Information is used effectively and contributes in profit creation and not only support management judgment quick but important resource to be possible recycled. The recent information systems improve enterprise's competitive power by reflection of user's various requirements and becoming big and complex for adaptation of rapidly circumstance change. Also it is trend that importance of information quality is emphasized gradually. The biggest problem in user requirement that is based on low quality data support. In case of business management is achieved by low quality information, company can not help dropping their competitive power such as company's strategy establishment, strategy achievement and management concentration breakup against competitor. Information of low quality increase time and expense to improve inaccurate data or revise and it is hard to accept correct information from specific situation. To solve these problems, we have to gain high quality data through definite comprehension, data management system establishment, and systematic data management achievement etc. Up to now, information quality and connected study were developed partially, but systematic methodology of information quality management's whole condition was not existed. Therefore, in this paper can show you how to extract process for information quality management & related evaluate factor with CMM (Capacity Maturity Mode]) 5 steps that is information warranty of quality process step. This paper whishes to contributes in competitive company or organization activity through information quality improvement management process.

• Geophysics and Geophysical Exploration
• /
• v.23 no.1
• /
• pp.1-12
• /
• 2020

In the development of geodynamic structures such as subduction and rift zones, a weakening mechanism is essential for localized weak zone formation in the lithosphere. Shear heating, a weakening mechanism, generates short-wavelength temperature elevation in the lithosphere; the increased temperature can reduce lithospheric strength and promote its breakup. A two-dimensional elastoplastic extensional basin model was used to conduct benchmarking based on previous numerical simulation studies to quantitatively analyze shear heating. The amount of shear heating was investigated by controlling the yield strength, extensional velocity, and strain- and temperature-dependent weakening. In the absence of the weakening mechanism, the higher yield strength and extensional velocity led to more vigorous shear heating. The reference model with a 100-MPa yield strength and 2-cm/year extension showed a temperature increase of ~ 50 K when the bulk extension was 20 km (i.e., 0.025 strain). However, in the yield-strength weakening mechanism, depending on the plastic strain and temperature, more efficient weakening induced stronger shear heating, which indicates positive feedback between the weakening mechanism and the shear heating. The rate of shear heating rapidly increased at the initial stage of deformation, and the rate decreased by 80% as the lithosphere weakened. This suggests that shear heating with the weakening mechanism can significantly influence the strength of relatively undamaged lithosphere.