• Transactions on Electrical and Electronic Materials
• /
• v.13 no.5
• /
• pp.252-255
• /
• 2012

In order to characterize insulation properties of epoxy/micro-silica/nano-silicate composite (EMNC), long-term and short-term AC treeing tests were carried out undr non-uniform electric field generated between needle-plate electrodes. In a long-term test, a 10 kV (60 Hz) electrical field was applied to the specimen positioned between the electrodes with a distance of 2.7 mm in an insulating oil bath at $30^{\circ}C$, and a typical branch type electrical tree was observed in the neat epoxy resin and breakdown took place at 1,042 min after applying the 10 kVelectrical field. Meanwhile, the spherical tree with the tree length of $237{\mu}m$ was seen in EMNC-65-0.3 at 52,380 min (36.4 day) and then the test was stopped because the tree propagation rate was too low. In the short-term test, an electrial field was applied to a 3.5 mm-thick specimen at an increasing voltage rate of 0.5 kV/s until breakdown in insulating oil bath at $30^{\circ}C$ and $130^{\circ}C$, and the data was estimated by Weibull statistical analysis. The electrical insulation breakdown strength for neat epoxy resin was 1,763 kV/mm at $30^{\circ}C$, while that for EMNC-65-0.3 was 2,604 kV/mm, which was a modified value of 47%. As was expected, the breakdown strength decreased at higher test temperatures.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.5
• /
• pp.711-716
• /
• 2012

To assess the insulation deterioration of stator windings, diagnostic and AC breakdown tests were performed on the eleven high voltage (HV) motors rated at 6kV. After completing the diagnostic tests, the AC overvoltage test was performed by gradually increasing the voltage applied to the stator windings until electrical insulation failure occurred, to obtain the breakdown voltage. Stator winding of motors 1, 3, and 8 failed at above rated voltage at 14 kV, 13.8kV, and 16.4kV, respectively. The breakdown voltage of three motors was higher than expected for good quality windings in 6kV motors. Based on deterioration evaluation criteria, the stator winding insulation of eleven HV motors are confirmed to be in good condition. The turning point of the current, $P_{i2}$, in the AC current vs. voltage characteristics occurred between 5kV and 6kV, and the breakdown voltage was low between 13.8kV and 16.4kV. There was a strong correlation between the breakdown voltage and various electrical characteristics in diagnostic tests including Pi2.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.78-81
• /
• 2004

In this paper, the effect of adhesion properties of semiconductive-insulating interface layer of silicone rubber on electrical properties was investigated. Surface structure and adhesion of semiconductive silicon rubber by surface asperity was obtained from SEM and T-peel test. In addition, ac breakdown test was carried out for elucidating the change of electrical property by roughness treatment. From the results, Adhesive strength of semiconductive-insulation interface was increased with surface asperity. Dielectric breakdown strength by surface asperity decreased than initial Specimen, but increased from Sand Paper #1200. According to the adhesional strength data unevenness and void formed on the silicone rubber interface expand the surface area and result in improvement of adhesion. Before treatment Sand Paper #1200, dielectric breakdown strength was decreased by unevenness and void which are causing to have electric field mitigation small. After the treatment, the effect of adhesion increased dielectric breakdown strength. It is found that ac dielectric breakdown strength was increased with improving the adhesion between the semiconductive and insulating interface.

• Electrical & Electronic Materials
• /
• v.10 no.3
• /
• pp.255-261
• /
• 1997

In this study, pore-containing barium titanate ceramics were prepared with different porosities and pore sizes, in order to better understand how porosity and pore size affect electrical breakdown of barium titanate ceramics. A granulated barium titanate powder was mixed with three grades of commercial polymer microspheres up to 11wt%. The electrical breakdown test was performed at two different temperatures of 30.deg. C(below Tc) and 150.deg. C(above Tc) for samples immersed in a silicon oil bath using a 60kV de power supply. Electrical breakdown strength of pore containing barium titanate ceramics with porosity lower than 10% decreased as pore size and porosity increased. However, above the 10% porosity region, electrical breakdown strength decreased as the pore connectivity increased. From the experimental results, an optimum electrical breakdown model is proposed in an attempt to explain the effect of pores.

• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1217-1222
• /
• 1996

Undoped barium titanate ceramic samples with high density were produced by using both high purity hydro-thermally synthesized and oxalate-derived powders. Sintering temperature was varied in the temperature range 128$0^{\circ}C$-140$0^{\circ}C$ to control the average grain sizes of the samples. Electrical breakdown test was performed at two different temperature with 3$0^{\circ}C$(below Tc) and 15$0^{\circ}C$ (above Tc) for samples immersed in silicon oil bath using 60kV dc power supply. From the experimental results at below and above Curie temperature the grain size and thickness dependence of electrical breakdown strength for BaTiO3 ceramics was presented and breakdown behavior was also studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.137-141
• /
• 1996

This paper deals with the prebreakdown phenomena of $SF_{6}$ gap stressed by non-oscillating and oscillating impulse voltages in a strong inhomogeneous field disturbed by a fred needle shaped-protrusion on the earth-side electrode. The breakdown voltage-time characteristics were measured for both positive and negative polarities and over the gas pressure range of 0.1∼0.5 MPa, and the temporal developments of the 77breakdown were observed by a shunt of 50 n. The dependence of the leader stopping time on the gas pressure were obtained. The local field enhancement due to the space charges, which is produced by the streamer corona, has influence with the electrical breakdown of the test gap. The test streamer corona is oxy a necessary condition for the electrical breakdown and the subsequent ionization activities launch the leader at the local field region.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.2
• /
• pp.60-63
• /
• 2004

The electrical breakdown characteristics of different types of soil samples have been measured. It is shown that the threshold soil breakdown strength is affected by many factors, such as types of soil, grain size, and soil compaction. The breakdown process in the test soil samples appears to be due to air ionization in the voids between the soil particles. The results have been compared with the relevant experimental results of other researchers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.793-797
• /
• 2007

In this paper, the long time breakdown characteristic of the epoxy composite, which is widely used in the insulation system for high voltage application, was estimated with Weibull distribution. In the procedure of the estimation, the short time breakdown characteristics for the epoxy composite specimens, which were made with the variation of hardener and/or filler, were tested firstly. Then the long time voltage-to-time test was implemented. Finally, the long time breakdown voltage of each specimen was estimated with the parameters obtained from the statistical treatment with Weibull distribution. Base on the results, it has been found that the optimal weight ratio of epoxy resin/hardener/filler that has the excellent long time breakdown characteristic was 100/100/65. It was due to the silane treatment which relieves the electric field at the interface between filler and epoxy.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.191-193
• /
• 1991

In this paper, we introduce silicon dioxide films deposited by Laser CVD, and evaluate the breakdown characteristics of these films by TZDB(Time Zero Dieiectric Breakdown) and TDDB(Time Dependent Dielectric Breakdown) test, failure times against eletric field are examined and accelation factors ${\beta}$ are obtained, and also, long term reliability is described by examining TDDB under positive voltage bias, all the above results are compared with PECVD(Plasma Enhanced CVD) $SiO_2$ breakdown, data, as a result, it is shown that the breakdown characteristics of Laser CVD $SiO_2$ films is improved.

• 전기의세계
• /
• v.29 no.2
• /
• pp.129-132
• /
• 1980

For large gas-insulated systems, the conductor utilized possess some degree of surface roughness which locally enhances the applied field at highpressure in $SF_{6}$. In order to investigate the effect of field enhancement on the breakdown field strength, the spheric protrusion was employed which gives a quantitative analysis on field enhancement. For further investigations on the breakdown level and polarity effect in $SF_{6}$, the repeated breakdown tests were performed with d.c. voltage at pressures up to about 4 bar. The experimental results show that the breakdown level does vary noticeably due to successive voltage applications and the breakdown field strength measured for a test gap with the cathode protrusion is markedly lower than that determined from the identical anode protrusion.