• International journal of advanced smart convergence
• /
• v.6 no.1
• /
• pp.76-81
• /
• 2017

This paper presents a low cost and flexible IoT enabled smart LED controller using Arduino that is used for emergency exit signs. The Internet of Things (IoT) is become a global network that put together physical objects using network communications for the purpose of inter-communication of devices, access information on internet, interaction with users as well as permanent connected environment. A crucial point in this paper, is underlined on the potential key points of applying the Arduino platform as low cost, easy to use microcontroller with combination of various sensors applied in IoT technology to facilitate and establishment of intelligent products. To demonstrate the feasibility and effectiveness of the system, devices such as LED strip, combination of various sensors, Arduino, power plug and ZigBee module have been integrated to setup smart emergency exit sign system. The general concept of the proposed system design discussed in this paper is all about the combination of various sensor such as smoke detector sensor, humidity, temperature sensor, glass break sensors as well as camera sensor that are connected to the main controller (Arduino) for the purpose of communicating with LED exit signs displayer and dedicated PC monitors from integrated system monitoring (controller room) through gateway devices using Zig bee module. A critical appraisal of the approach in the area concludes the paper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.9
• /
• pp.2894-2900
• /
• 1996

The stream generator tubes represent an integral part of a major barrier against the fission product release to the environment. So, the rupture of these tubes could permit flow of reactor coolant into the secondary system and injure the safety of reactor coolant system. Therefore, if the crack was detected during In-Service Inspection of tubes the cracked tube should be evaluated by the pulgging criteria and plugged or not. In this study, the fracture mechanics evaluation is carried out on the thru-wall axial crack due to Primary Water Stress Corrosion Cracking in the roll transition aone of steam generator tube to help the assurence the integrity of tubes and estabilish the plugging criteria. Due to the Inconel which is used as tube material is more ductile than others, the plastic instability repture theory was used to calculate the critical and allowable crack length. Based on Leak Before Break concept the leak rate for the critical crack length and the allowable leak rate are compared and the safety of tubes was given.

• Journal of Conservation Science
• /
• v.29 no.4
• /
• pp.407-420
• /
• 2013

The stone sculptures in Gyeongbokgung Royal Palace are mainly composed of granite (884 sculptures, 96.7%) and marble (25 sculptures, 2.7%) that originated in several different quarries. Main deterioration forms are crack (24%), break-out (21%), exfoliation (36%), granular disintegration (9%) and blackening (20%). Crack and break-out are dominant contributors to high physical deterioration degree, and blackening is major weathering form of intensive discoloration. The Gyeonghoeru, Geunjeongjeon and Pumgyeseok areas require urgent and high conservation maintenance with short-term periodic monitoring since proportions of 3-grade deterioration were calculated higher than others as 55% for Gyeonghoeru, 29% for Geunjeongjeon, 11% for Pumgyeseok area. The Pumgyeseok (officials' rank stone), especially, needs intervention for protective facility due to its material vulnerability to weathering in outdoor environment.

• The Journal of Korean Physical Therapy
• /
• v.16 no.4
• /
• pp.23-37
• /
• 2004

Fibromyalgia syndrome(FMS) is a chronic pain disorder of unknown etiology characterized by widespread musculoskeletal aches and pains, stiffness, and general fatigue, disturbed sleep and sleepiness. Frequently misdiagnosed, FMS is often confused with myofascial pain syndrome, polymyalgia rheumatica, polymyositis, hypothyroidism, metastatic carcinoma, rheumatoid arthritis (RA), juvenile rheumatoid arthritis, chronic fatigue syndrome, or systemic lupus erythematosus, any of which may occur concomitantly with FMS. The management of FMS often begins with a thorough examination and a diagnosis from a physician who is formally trained in tender-point/trigger-point recognition. An initial diagnosis provides reassurance to the patient and often reduces the anxiety and depression patterns associated with FMS. The most common goals in the management of FMS are (1) to break the pain cycle, (2) to restore sleep patterns, and (3) to increase functional activity levels. Because FMS is a multifactorial syndrome, it is likely that the best treatment will encompass multiple strategies. Medication with analgesics and antidepressants and also physiotherapy, are often prescribed and give some relief. The other most effective intervention for long-term management of FS to date is physical exercise. Physical therapists can instruct patients in the use of heat at home (moist hot packs, heating pads, whirlpools, warm showers or baths, and hot pads) to increase local blood flow and to decrease muscle spasm and tension. Also instruct patients in the proper use of cold modalities (ice packs, ice massage, and cool baths) to anesthetize localized areas of pain (tender points) and break the pain cycle. Massage and tender-point massage also may promote muscle relaxation. To date, the two most important interventions for the long-term management of FS are patient education and physical exercise. Lately, is handling FMS and Chronic Fatigue syndrome(CFS) together, becuase FMS and CFS are poorly understood disorders that share similar demographic and clinical characteristics. Because of the clinical similarities between both disorders it was suggested that they share a common pathophysiological mechanism, namely, central nervous system dysfunction.

• Journal of the Korean Society for Railway
• /
• v.14 no.6
• /
• pp.535-544
• /
• 2011

The rail surface defects can cause the high impact load on the track and lead to the progress of the rail fatigue damage and the rail break. In case of the rail break, there is a great deal of risk for derailment, and thus the maintenance criteria for the rail surface defects are of great importance. In this study, using the dynamic train-track interaction analysis program, the impact wheel loads and rail bending stresses according to the depths of the surface defects have been calculated with the input data of the rail surface irregularities measured at 43 spots with surface defects in the ballasted track of high-speed railway. Considering the irregularity of track geometry, the allowable limits of wheel load and rail bending stress have been set, and the maintenance criteria for the rail surface defects was suggested by analyzing the relationship of the maximum values of wheel load and rail bending stress versus depth and width of rail surface defect. The analysis results suggest that the allowable depth of the surface defect is determined approximately 0.2mm from the limit of the impact wheel load.

• Water for future
• /
• v.29 no.3
• /
• pp.197-205
• /
• 1996

Flow carrying capacity of water distribution systems is getting reduced by deterioration of pipes in the systems. The objective of this study is to develop a managerial decision-making model for the rehabilitation of water distribution systems with a minimum cost. The decisions made by the model also satisfy the requirements for the discharge and pressure at demanding nodes in the system. The replacement cost, pipe break repair cost, and pumping cost are considered in the economic evaluation of the decision along with the break ratio and interest ratio to determine the optimal replacement time for each pipe. Then, the hydraulic integrity of the water distribution system is checked for the decision by a pipe network simulator, KYPIPE, if the discharge and pressure requirements, the decision made for the optimal replacement time is revised until the requirements are satisfied. The model is applied to an existing water distribution system, the Metropolita Water Supply Project (1st Phase). The result shows that the decisions for the replacement time determined by the economix analysis are accepted as optimal and the hydraulic integrity of the system is in good condition.

• Korean Journal of Food Science and Technology
• /
• v.19 no.1
• /
• pp.69-74
• /
• 1987

These studies were conducted to investigate the changes in carbohydrate properties of the endosperm during the stages of maturity. Original moisture continued to decrease while 1,000-kernel weight and test weight increased steadily in all varieties with maturation. Starch content of the endosperm increased continuously by 35 to 40 days after heading. The B-type starch granules synthesis of the the early mature variety, Chokwang, was depressed at the later stages of development. Amylose and amylopectin components of starch both increased as the kernel matured, and amylose-amylopectin ratio also increased during the same period. Amount of pentosan per kernel basis increased throughout the maturation period. Amylograph break-down had a highly negative coefficient correlation with starch and pentosan content of endosperm. Results indicated that wheat maturation was characterized by an increase in the starch and pentosan content of the kernel.

• Journal of the Korean Society of Safety
• /
• v.23 no.5
• /
• pp.119-124
• /
• 2008

Many automobile assembly workers often do several cycles of tasks continuously, i.e., without breaks, to get a longer break. This is not recommended since the dose of fatigue increases exponetially with time and it takes much longer time to recover. In this study, a laboratory experiment was conducted to investigate the effect of work/rest schedules on workload of a repetitive upper-limb task. Eleven male subjects participated in the experiment, in which simulated screw driving tasks were carried out repetitively with 3 different work/rest schedules: standard breaks(1 cycle of work at a time, 60 20-s breaks), medium breaks(5 cycles of work at a time, 12 100-s breaks), and long breaks(10 cycles of work at a time, 6 200-s breaks). The result showed that medium- and long-breaks schedules significantly increased the level of perceived discomfort and %HRR as compared to the standard-break schedule. The subjects' preference was not statistically different among work/rest schedules, which might be caused from the absolutely low level of workload of the experimental tasks. From the results, it is recommended to have frequent and shorter breaks rather than infrequent and longer breaks to decrease the level of physical workload. A more expanded studies, however, should be carried out to provide more practical safety guidelines on the work practice of continuous working without breaks among automobile assembly workers.

• Journal of Navigation and Port Research
• /
• v.37 no.6
• /
• pp.597-601
• /
• 2013

Recently, many studies about the wave power generation system for the marine structure as the hybrid form in linked with the original features have been made of. Of these, the wave power generation system using oscillating water column(OWC) has function to convert wave energy to electrical energy with original function of the break water structure. In this type of generation system, it is important to make the flow of sea water as much as possible without loss. Output characteristics of wave power generation system depending on entrance section were described in the paper. Also, flow quantity changing with entrance section, velocity of sea water and output of wells turbine were measured by simulating OWC wells turbine model in break water, one of the general marine structure. Finally, entrance section was suggested to enhance the energy conversion efficiency based on the results of simulation.

• FLOWER RESEARCH JOURNAL
• /
• v.17 no.4
• /
• pp.297-302
• /
• 2009

This study was carried out to investigate the characteristics of rooting and bud break of single-stemmed roses (Rosa hybrida L. 'Rate Rose' and 'Teresa') as affected by axillary bud position and leaf area of cuttings derived from different growth stage of the mother shoots. In fact, both rooting and budbreak of single-stemmed roses were not influenced by growth stage of mother shoots, with showing more than 95% in all treatment related to mother shoot maturity. 'Rote Rose' required 34 days to average rooting and budbreak after cutting, whereas 'Teresa' did only 18 days to budbreak which was 9 days faster than rooting. Rooting and bud break needed more time and showed lower percent as the axillaty bud position for cuttings went down to the base of mother shoots. Especially 'Teresa' showed 12 days of delay to budbreak and 14.4% decrease in budbreak. Also, the increase in leaf area of cuttings accelerated rooting and budbreak, of which the time was shorter and the percent was higher.