• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1998.11a
• /
• pp.59-69
• /
• 1998

ABS sensor ring has been manufactured by P/M method using 400 series ferrite stainless steel. the results are as following : It is supposedly sufficient to use for control computer due to good experimental results of magnetic characteristics. Compared with sensor ring made by iron, 400 series ferrite stainless steel has shown a good corrosion resistance without an addition surface treatment. Thus the decreasing production process has been obtained. As a result of hardness and tensile test, 400 series ferrite stainless steel shown a good endurance when it is combined to C/V joint, and has a good hardness properties endurable In sand and pebble impact.

• International Journal of Automotive Technology
• /
• v.5 no.2
• /
• pp.109-114
• /
• 2004

This paper presents a closed-loop evaluation of the Vehicle Stability Control (VSC) system using a vehicle simulator. Human driver-VSC interactions have been investigated under realistic operating conditions in the laboratory. Braking control inputs for vehicle stability enhancement have been directly derived from the sliding control law based on vehicle planar motion equations with differential braking. A driving simulator has been validated using actual vehicle driving test data. Real-time human-in-the loop simulation results in realistic driving situations have shown that the proposed controller reduces driving effort and enhances vehicle stability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.65-70
• /
• 2014

An Integrated Dynamics Control system with four wheel Steering (IDCS) is proposed and analysed in this study. It integrates and controls steer angle of front and rear wheel simultaneously to enhance lateral stability and steerability. An active front steer (AFS) system and an active rear steer (ARS) system are also developed to compare their performances. The systems are evaluated during brake maneuver and several road conditions are used to test the performances. The results showed that IDCS vehicle follows the reference yaw rate and reduces side slip angle very well. AFS and ARS vehicles track the reference yaw rate but they can not reduce side slip angle. On split-${\mu}$ road, IDCS controller forces the vehicle to go straight ahead but AFS and ARS vehicles show lateral deviation from centerline.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.103-111
• /
• 2008

One of the most popular internal combustion engines is the engine in the transportation device. Power is a parameter that shows the capabilities of an object that gives energy, for example the internal combustion engine. Power in this engine is measured by a device called dynamometer. The CFD (Computational Fluid Dynamic) fluent software was simulated several impeller variables to absorb power of engine. With that result, we knew the biggest dynamometer absorber power, cheapest and easy to be made. The hydraulic dynamometer is selected type of dynamometer as the result of design process. The basic principle of a hydraulic dynamometer is the same as centrifugal pump but it has low pump efficiency. The results of the test are maximum power and torque of the tested engine and the operation area of the selected hydraulic dynamometer.

• Tribology and Lubricants
• /
• v.25 no.6
• /
• pp.381-386
• /
• 2009

In general, a brake system of axle for heavy duty machine as a wheel excavator makes use of wettype multiple disk brakes. These disk bakes are very important parts of heavy duty machine because they are dvanced in durability and braking power, and can be designed compactly. Thus, we adesigned and made wettype multiple disk brakes of axle for the wheel excavator to be localization of these imported all. In this study, wet multiple disk brakes were made a comparative test with the 3 types materials of friction disk by the SAE No.2 dynamometer. The friction characteristics were measured and analyzed to decide a suitable material as wear depth of friction disk and dynamic and static friction coefficient on temperature of oil and applied pressure.

• Tribology and Lubricants
• /
• v.25 no.2
• /
• pp.102-107
• /
• 2009

The thermal deformation volume of motorcycle break disk was studied using a disk-on-pad type friction tester. Thermal deformation volume of motorcycle break disk have an effect on the frictional factor such as applied load, sliding speed, sliding distance and number of ventilated disk hole. However, it is difficult to know the mutual relation of these factors on thermal deformation volume. In this study, the thermal deformation volume with ANSYS workbench are obtained by application of temperature from mechanical test. From this study, the result was shown that the motorcycle break disk with ventilated hole 3 have the most excellent thermal deformation characteristics. The regression equation with frictional factors which have a trust rate of 95% for prediction of thermal deformation volume of motorcycle break disk was composed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.589-595
• /
• 2003

DME(Dimethyl ether) is an oxygenated fuel with a octane number higher than that of diesel oil. It meets the ULEV emission regulation and reduces the smoke to almost zero when used in a diesel engine. In the present study, engine performance and exhaust emissions were investigated with a conventional DI diesel engine which has a jerk type injection pump. Test results showed that the power with DME were almost same as that of pure diesel oil, and the brake thermal efficiency increased a little. Also, smoke index from DME engine showed nearly zero level, but NO$_{x}$ was increased compare to diesel oil.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.73-78
• /
• 2001

In this study, the friction weldability and properties of inconel alloy(IN738LC) to stainless steel (STS304) was investigat-ed. Upset length increased according to increment of friction pressure and time. The tensile strength of the friction weld-ing reached 85% of the STS304 base metal strength under the conditions of 8 sec friction time, 50MPa friction pressure and 150 MPa upset pressure. From the result of fracture surface analysis, IN738LC section can be joined with STS 304 materials in shape of a convex lens. Also, the temperature of welded interface was measured with k-type thermocouple. Finally the plastic flow confirmed at the welded interface STS304 by micro test.

• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.677-681
• /
• 2006

In general, the braking system of high speed train has an important role for the safety of the train. To stop the train safely at its pre-decided position, it is necessary to combine the various brakes properly. The Korean high speed train (HSR-350x) has adopted a combined electrical and mechanical (friction) braking system. In this study, the measuring method that can obtain the disc braking forces and friction coefficient between disc and pad during on-line test of HSR-350x has been suggested and verified through the comparison of the results obtained from this method and those of the results of the dynamo-tests.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.40-44
• /
• 2007

Light rail vehicle is optimized vehicle system for complex urban circumstance. LRT systems have many merits such as improve accuracy, speediness and safety. There are many LRT systems such as monorail, tram, automated guideway transit, linear induction motor propulsion and so on. These systems have operated in Japan and other advanced countries. In Korea, local government has many projects to apply the advanced LRT system. But there are no standardized specification, performance test specification, construction specification for monorail system, linear induction motor propulsion system, tram in Korea up to now. So, we need to establish of standardized to economical construction and safety. The linear induction motor system has been usually applied in Japan subway and ART(Advanced Rapid Transit) of Canada. In Korea, the linear induction motor system has been adopted for Yongin LRT and currently under construction. This paper covers the contents and technical base for main items of rolling stock, performance standard, carbody structure, bogie, electronic unit and brake equipment in order to implement linear induction motor LRT system according to local conditions.