• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2005년도 추계정기총회 및 제26회 학술발표대회 고분자리싸이클링기술 특별심포지엄
• /
• pp.243-247
• /
• 2005

본 연구에서는 화력발전소 바닥재를 중금속 흡착제로 활용하기 위한 기초연구로서 수열합성법에 의해 제올라이트를 합성하였다. 화력발전소 바닥재를 분쇄하여 반응온도$(80{\sim}150^{\circ}C)$ 및 NaOH 농도$(1{\sim}5M)$를 변화시키면서 알칼리 수열합성법으로 반응시킨 결과, NaP1, hydrxoy-sodalite, tobermorite 등이 생성되었으며, 양이온 교환 능력이 높은 NaP1은 $120^{\circ}C$ 이하의 온도와 2M 이하의 NaOH 농도에서 주로 합성되었다.

• 환경위생공학
• /
• 제13권2호
• /
• pp.121-127
• /
• 1998

This study was to understand leaching characteristics with pH controlling agents and Temp. control, and investigate leaching characteristics with pH control from opening a leaching test to an end for reassessing leaching test of heavy metals with environmental conditions in landfill. Because leaching of heavy metals was increased in low pH, pH must control for leaching in existing leaching test. Generally, regulation time(6hr) of leaching was confirmed reasonablely, except for Cu in plating sludge. In pH controlling solution, there was nearly not difference between Acetic acid and HCl and if considering Cu, the former was appropriate. In a part of heavy metal, leaching rate was increased in high Temp., and normal Temp. in existing leaching test would be revaluated.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2004년도 춘계임시총회 및 제23회 학술대회
• /
• pp.155-158
• /
• 2004

본 연구에서는 공냉(空冷)된 화력발전소 바닥재의 입도분포, 화학조성, 광물상 등 기초 특성과 압축강도비에 의해 포졸란 반응성을 측정하였다. 바닥재의 주요 성분은 $SiO_2$, $Al_2O_3,\;Fe_2O_3$로 이들의 합계가 91.2wt.%였으며, 주요 광물상은 mullite, quartz, cristobalite, tridymite, hematie 등이었다. 입도별 화학조성 변동은 거의 없었으나, 입도가 커짐에 따라 $SiO_2$는 quartz에서 cristobalite로 존재하는 비율이 증가하였다. 분쇄된 바닥재(blame 비표면적 $7,540cm^2/g$)의 양생 28일에서의 활성도 지수는 101을 나타내었다.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2004년도 춘계임시총회 및 제23회 학술대회
• /
• pp.159-163
• /
• 2004

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.328-329
• /
• 2018

The problem of imbalance between supply and demand of fine aggregates in the southeastern region due to the decrease in collection of EEZ(Exclusive Economic Zone) sea sand has been raised. In this paper, the possibility of securing alternative aggregate as a means to solve the problem of fine aggregate shortage in the southeast region was analyzed. As a result of the analysis, the alternative aggregate is easy to manufacture and its quality can be secured. And, it is suitable to use as an aggregate with less environmental burden. In addition, institutional improvement measures are needed for effective utilization and recycling of alternative aggregates.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.1175-1180
• /
• 2000

Recently, the crack of concrete induced by the heat of hydration of cement is a serious problem for more greater, special and higher strength of concrete structures. The increasing concrete's temperature is mainly caused by the heat of hydration of cement and so, to control the thermal stress of concrete structure is desirable to use low heater material of hydration. There are many methods to diminish the increasing of concrete temperature such as using of low heat cement, addition of fly-ash, application of pre-cooling, etc., and in this study, we evaluate the heating and mechanical properties of ultra low heat mass concrete using Low Heat Portland(KS Type IV) cement with 30% of limestone powder. The results of this study will be applied to side wall and bottom of No. 15 and 16 of underground LNG tank in Inchon.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.461-464
• /
• 2005

As the research on the development of the lightweight concrete block by the hydro-thermal synthetic reaction mixed with the calcareous material and bottom ash that is used less among siliceous material, we studied on the physical and chemical characteristics in the changes of hydro-thermal synthetic reaction of lightweight concrete block compounded with the PP fiber to increase flexural toughness and to prevent fragility failure. The results of the experiment are as follow. According to the increase of hydro-thermal synthetic reaction and the fiber content, compressive and flexural strength increased. Despite the changes of the hydro-thermal synthetic reaction time, tobermorite was produced on each of the specimens similarly. However, the phase of tobermorite was changed in accordance with the changes of time. Also, $CaCo_{3}$ appeared on the surface of the 9 hour hardened specimen.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.182-183
• /
• 2019

In this study, the optimization of mixing proportion of press-forming board with blast furnace slag, pearlite and bottom ash was investigated using the response surface methodology. Ten Mixing proportions of specimens were designed by the response surface design, and then flexural failure load, moisture content and water absorption of specimens were measured. As a result of the reaction surface analysis based on the experimental results, it was possible to derive the optimal mixing proportion with the satisfaction of 93%.

• 한국해양공학회지
• /
• 제26권2호
• /
• pp.39-47
• /
• 2012

The objective of this study was to develop a strength prediction model using a polynomial regression analysis based on the experimental results obtained from ninety samples. As the results of a correlation analysis between various mixing factors and unconfined compressive strength using SPSS (statistical package for the social sciences), the governing factors in the strength of lightweight soil were found to be the crumb rubber content, bottom ash content,and water-cement ratio. After selecting the governing factors affecting the strength through the correlation analysis, a strength prediction model, which consisted of the selected governing factors, was developed using the polynomial regression analysis. The strengths calculated from the proposed model were similar to those resulting from laboratory tests (R2=87.5%). Therefore, the proposed model can be used to predict the strength of lightweight mixtures with various mixing ratios without time-consuming experimental tests.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2006년도 춘계임시총회 및 제27회 학술발표대회
• /
• pp.145-149
• /
• 2006