• Journal of the Korean Geosynthetics Society
• /
• v.15 no.4
• /
• pp.53-62
• /
• 2016

This paper presents the results of a reduced-scale physical model investigation into the effect of drilling fluid with different mix designs for use in offshore bore hole collapse prevention. Compare the bentonite and Attapulgite use. Reduced-scale model tests were then carried out considering field procedures for cases with decomposed granitic soil with fines and a sand with various drilling fluids with different mix designs. The results were indicated that the addition of polymer to the bentonite based drilling fluid decreases the amount of injected drilling fluid and increases the final depth of excavation. Also revealed that the effect of polymer on the performance of drilling fluid is more pronounced in the decomposed granite soil with fines than sand. Practical implications of the findings from this study are discussed in detail.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.185-192
• /
• 1999

It had found that, as a result of cross-hole tonic logging test, concrete was not filled partially within the bottom 2.0 m of the large diameter (Ø= 2,500mm) rock socketed pile, MP20-P11(socket diameter (Ø= 2,200mm), which was a pile among piles group supporting a pier of Kwangan Grand Bridge. The pile was repaired by the combined cement grout injected through the pipes for the cross-hole sonic logging test and the bore holes for core samples. A month after the cement grouting, repairing was checked by coring and cross-hole sonic logging then 3 times of grouting and 2 times of coring were, in turns, peformed, then repairing was completed successfully. The vertical compressive capacity of the repaired large diameter socketed pile was evaluated by several formulas and software ROCKET, and was more conservative than design load (1,882 ton) of MP20-P11. It is expected that, in the case of the battered socketed piles, it could be more reasonable to analyze the behaviors of a battered pile using 3-D model. A 3-D analysis will be peformed in the future study.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.357-364
• /
• 1999

In recently site investigations, the need for the determination of dynamic soil properties such as dynamic modules of rigidity, elasticity, dynamic poison's ratio and damping ratio etc. is increasing for the astigmatic designs of the civil structures. To obtain some of the dynamic properties, measurement of elastic waves velocity, both P and S wave, is required. Among various methods to measure elastic wave velocity such and Down Hole, Cross Hole and Refraction etc., Suspension P.S. Logging has an advantage to use for the off-shore investigation where generation of the shock wave and traveling of the wave is difficult. In suspension P.S. logging, specially designed prove equipped with source of shock wave, two 3-channel receivers, departing 1m distance, and other auxiliary facilities is inserted down in a bore hole bottom and raised in predetermined interval, usually 1m or 2m, and measurement is conducted. P.S. logging have been conducted in a off-shore construction project near InChon in the west coast for the first in the country, and form the result, potential of the liquefaction of the subsoil was evaluated and compared with the conventional method.

• Journal of The Geomorphological Association of Korea
• /
• v.25 no.3
• /
• pp.43-55
• /
• 2018

This study aimed to identify different sedimentary environments of Gochang coast according to geomorphic conditions of each bore hole. To achieve the aim, this study utilized the classification of sedimentary environmental conditions of surface sediment, which was based on grain size distribution characteristics.In other words, three sedimentary environmental conditions ofsandy flat + sand beach, coastal sand dune and weathered bedrock soil, which were distinguished based on grain size distribution characteristics of mean-sorting for surface sediments, were applied to the sediments of bore holes. Four sedimentary environments could be identified in Gochang coast. First, the lake sedimentary environment originated from terrestrial sediments seems to have been dominated by weathered bedrock soil that the surface flow has deposited in a coastal wetland or a boundary, which is affected by the sea. Second, the lake sedimentary environment that is little affected by coastal sand dunes is located at the center of a valley, which is connected to the land, and the dune slack of Saban-ri. The surface flow of weather bedrock soil is the main source of deposits. However, there seems to have been a temporary influence of the sea. Third, the lake sedimentary environment that is strongly affected by coastal sand dunes is located at the dune slack of Yeongjeong-ri. This environment shows traces of a change from a coastal sand dune into the dune slack. Finally, the coastalsand dune sedimentary environment, which wasinvestigated by boring the current coastal sand dune, shows a temporary influence of the land but seems to have maintained the overall stability. Consequently, this study demonstrated that the grain size distribution characteristics of the present surface sediments could be effectively applied to identify the sedimentary environments of the paleo bore hole sediments. In addition, the paleo change of sedimentary environment could also be identified in many places of Gochang coast. If the results of this study are combined with the age dating and geochemical analysis in future works, the paleo environmental change in Gochang coast will be restored more precisely.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.111-116
• /
• 2011

Three-dimensional finite element analyses have been performed to improve the durability of bulkhead. To keep pace with design changes and concentrate on regions of interest, SUBMODEL technique in ABAQUS was used for analysis. An analysis was conducted with following load cases: 1) Cap press-fit, 2) Bearing crush, 3) Bolt assembly, 4) Hot assembly, 5) Firing load, 6) Alternating firing load, 7) 2nd hot assembly. Fatigue analysis was done using commercial software FEMFAT and fatigue factors at the interested regions such as bolt tip area, counter bore, breathing hole, honing clearance were calculated and compared to aid design validation. Finite element modeling in the area of thread engagement used a simple constraint equations. Increasing bolt length, to a minimum of 39 mm above joint face gives a better fatigue resistance to the bulkhead. Breathing hole helps not only circulate the air in the crankcase but also fatigue resistance of bulkhead by relieving the stress at the critical locations.

• The Journal of Engineering Geology
• /
• v.15 no.2 s.42
• /
• pp.213-227
• /
• 2005

This study aims to assess the problems with investigation method and to suggest the complementary solutions by comparing the predicted data from surface investigation with the outcome data from underground cavern. In the study area, one(NE-1) of 6 fracture zones predicted during the surface investigation was only confirmed in underground caverns. Therefore, it is necessary to improve the confidence level for prediction. In this study, the fracture classification criteria was quantitatively suggested on the basis of the BHTV images of NE-1 fracture zone. The major orientation of background fractures in rock mass was changed at the depth of the storage cavern, the length and intensity were decreased. These characteristics result in the deviation of predieted predicted fracture properties and generate the investigation bias depending on the bore hole directions and investigated scales. The evaluation of hydraulic connectivity in the surface investigation stage needs to be analyze by the groundwater pressures and hydrochemical properties from the monitoring bore hole(s) equipped with a double completion or multi-packer system during the test bore hole is pumping or injecting. The hydraulic conductivities in geometric mean measured in the underground caverns are 2-3 times lower than those from the surface and furthermore the horizontal hydraulic conductivity in geometric mean is six times lower than the vertical one. To improve confidence level of the hydraulic conductivity, the orientation of test hole should be considered during the analysis of the hydraulic conductivity and the methodology of hydro-testing and interpretation should be based on the characteristics of rock mass and investigation purposes.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.33-43
• /
• 2008

In this study, for the purpose of evaluating the shear wave velocity in core zone, cross-hole test, down-hole test, MASW (Multi-channel Analysis of Surface Wave), and seismic reflection survey were carried out on the crest of the existing 'Y' dam. The results of field tests were compared one another. Furthermore, the field test results were compared with the result by the Sawada's empirical recommendation method. The purpose of this study is to compare the results of four kinds of field tests for evaluation of shear wave velocity in core zone of existing dam, to verify applicability of the empirical method which was recommended by Sawada and Takahashi, and to recommend a reasonable method for evaluation of shear wave velocity which is needed to evaluate tile maximum shear modulus of core zone. From the results of four kinds of field tests such as cross-hole test, down-hole test, MASW, and seismic reflection survey, it was found that the shear wave velocity distributions were similar within 18 m in depth and the results obtained by MASW and seismic reflection survey were almost the same by 30 m in depth. For evaluation of shear wave velocity in core zone of the existing dam, in consideration that it is not easy to bore the hole ill the core zone of existing dam, surface surveys such as MASW and seismic reflection method are recommended as realistic methods. On condition that it is impossible to conduct the field test and it is preliminary investigation, it is recommended that Sawada's low bound empirical equation be used.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.49-56
• /
• 2000

Instrumental observation of earth quakes in KIGAM was first attempted in the earty 1980`s by using 6 portable seismographs in the vicinity of Yang-San Faults. Now twenty-four permanent stations, which are equipped with short-period or broad-band seismometer, are included in seismic research network in KIGAM, including KSRS array station in Wonju which is consisted of 26 bore-hole stations. The seismic network of KIGAM is also linked to that of KEPRI(Korea Electric Power Research Institute)which is consisted of eight stations installed within and around the nuclear power plants. Owing to real-time data acquisition by telemetry, it became feasible to automatically locate hypocenters of the local events within fifteen minutes by computer data processing system, named KEMS(Korea Earthquake Monitoring System). Results of the hypocenter determination, together with observational data, are compiled and stored in the data base system. And they are published via web site whose URL is http://quake.kigam.re.kr KIGAM is also running t재 permanent geomagnetic stations installed in Daejun and Kyungju. The observed geomagnetic data are transmitted to Earthquake Research Centre in KIGAM by seismic network and compiled for the purpose of earthquake prediction research and other basic geophysical research.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.198.2-198.2
• /
• 2010

In this study, the COP variation with the duration of Ground Source Heat Pump (GSHP) systems operation was analyzed by experiment. This experimental facility was installed in residential house as a back-up device of solar thermal heating system. The capacity of heat pump is 2.5 kW with a vertical bore hole of 150m depth. The COP of GSHP is varied, depending on the ground temperature which is used as a heat source. The ground heat source temperature influencing heating COP is the soil or rock temperature which adjoin with geo-source heat exchanger. This temperature is decreased rapidly according to the operation duration of heat pump. As a result, COP of GSHP is decreased to 3 in one hour of continuous operation time.

• Proceedings of the Korean Information Science Society Conference
• /
• 2000.04b
• /
• pp.93-95
• /
• 2000

본 논문은 지반조사 정보 시스템이 관리하고 있는 시추공의 지층 구성 정보를 바탕으로 시추공을 클러스터링하여 지반의 구성을 분석하는 시스템의 설계 및 구현을 소개한다. 지반조사 정보시스템은 지반 시추공의 현장조사 및 실내시험을 통해 얻는 시추공 정보를 체계적으로 관리하여 정보의 재활용을 돕기 위한 데이터베이스 시스템이다. 본 논문에서 제안된 지반 분석 시스템은 지반조사 데이터베이스의 시추공 정보를 이용하여 지반이 가지고 있는 특성 정보를 추출하여 유사한 특성을 갖는 시추공의 집합으로 클러스터링하여 사용자에게 지반 구성 정보를 제공하는 시스템이다. 본 시스템에서 사용된 클러스터링 기법은 지반조사 데이터가 갖는 지반의 구성 요소 및 각 지층의 구성비를 통해 유사한 특성을 지니는 지반들을 그룹화하고, 그룹된 지반들의 특성을 찾는다. 그룹된 지반들의 분석을 통해 찾아진 유사한 특성은 지도상에 가시화함으로서 사용자에게 해당 지형에 대한 지반 특성을 제공한다.