• 전력전자학회논문지
• /
• 제25권2호
• /
• pp.133-141
• /
• 2020

The use of high-gain-voltage step-up converters for distributed power generation systems is being popularized because of the need for new energy generation and power conversion technologies. In this study, a new constructed high-gain-boost DC-DC converter was proposed to coordinate low voltage output DC sources, such as PV or fuel cell systems, with high DC bus (380 V) lines. Compared with traditional boost DC-DC converters, the proposed converter can create higher gain and has wider input voltage range and lower voltage stress for power semiconductors and passive elements. Moreover, the proposed topology produces multilevel DC voltage output, which is the main advantage of the proposed topology. Steady-state analysis in continuous conduction mode of the proposed converter is discussed in detail. The practicability of the proposed DC-DC converter is presented by experimental results with a 300 W prototype converter.

• 전력전자학회논문지
• /
• 제25권6호
• /
• pp.442-450
• /
• 2020

A small-signal modeling approach for a three-level boost (TLB) converter and a design methodology for a double-loop controller are proposed in this study. Conventional modeling of TLB converters involves three state variables. Moreover, TLB converters have two operation modes depending on the duty ratio. Consequently, complex mathematical calculations are required for controller design. This study proposes a simple system modeling method that uses two state variables, unlike previous methods that require three state variables. Analysis shows that the transfer functions of the two operation modes can be expressed as identical equations. This condition means that the linear feedback controller can be applied to all operational ranges, that is, for full duty ratios. The design method for a double-loop controller using a PI controller is presented in step-by-step sequences. Simulation and experimental verifications are conducted to verify the effectiveness of the small-signal analysis and control system design.

• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.70-75
• /
• 2015

High Step-up DC-DC Converters have been demanded for renewable energy applications. Transformer or coupled inductor is generally used to boost output voltage of converters. This methods can relatively obtain high voltage than others, whereas have heavy weight and high cost. To complement these disadvantages, we studied transformerless high step-up DC-DC converter. In various transformerless topologies, Boost converters combined with Cockcroft-Walton have studied. In this paper, we proposed a symmetrical Cockcroft-Walton circuit for transformerless high step-up DC-DC converter. Finally, we simulated proposed converter to compare with existing converter. As a result, proposed converter has higher duty ratio or lower cost than existing transformerless converters which are discussed in this paper.

• 한국정보통신학회논문지
• /
• 제18권5호
• /
• pp.1155-1161
• /
• 2014

본 논문에서는 DC-DC 부스트 컨버터의 최소 입력전압을 250mV 까지 낮출 수 있도록 하는 저전압 스타트업 전압 발생기를 제안 하였다. 제안된 스타트업 전압 발생기는 250mV의 입력전압을 500mV 이상으로 승압시켜 커패시터에 충전한다. 이후, 커패시터에 저장된 전압으로 부스트 컨버터를 시동시킴으로써, 250mV의 낮은 입력 전압에서도 부스트 컨버터가 동작을 시작할 수 있도록 하였다. 부스트 컨버터가 정상 동작한 후에는, 부스트 컨버터에 의하여 만들어지는 승압된 출력전압을 다시 부스트 컨버터의 전원으로 사용하게 함으로써, 스타트업 동작 후에는 기존 부스트 컨버터와 동일한 높은 전력 변환 효율로 동작 하도록 하였다. 제안된 스타트업 전압 발생기는 낮은 입력전압에서 트랜지스터의 바디전압을 조절하여 트랜지스터의 문턱전압을 낮춤으로써, 입력전압을 승압시키는 딕슨 차지펌프에 높은 클럭 주파수와 큰 전류를 공급하도록 하였다. 제안된 스타트업 전압 발생기는 $0.18{\mu}m$ CMOS 공정으로 제작되었으며, 250mV의 입력전압에서 생성된 클럭 주파수와 출력전압은 각각 34.5kHz와 522mV였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.571-575
• /
• 2002

Generation of electrical energy faces many problems today. Solar power converters were used to convert the electrical energy from the solar arrays to a stable and reliable power source. The object of this paper is to analyze and design DC-DC converters in a solar energy system to investigate the performance of the converters. A DC-DC converter can be commonly used to control the power flow from solar cell to load and to achieve maximum power point tracking(MPPT), DC-AC converter can also be used to modulate the DC power to AC power being applied on common utility load. A DC-DC converter is used to boost the solar cell voltage to constant 360(V) DC link and to ensure operation at the maximum power point tracking, If a wide input voltage range has to be covered a boost converter is required. In this paper, author described that simulation and experimental results of PV system contain solar modules, a DC-DC converter(boost type chopper), a DC-AC converter (3-phase inverter) and resistive loads.

• Journal of Power Electronics
• /
• 제15권2호
• /
• pp.338-345
• /
• 2015

The time-optimal control for boost converters can achieve the minimum recovery time. However, their output voltage deviation is quite large. Since the minimum output voltage deviation and minimum recovery time cannot be obtained at the same time, a novel energy control is proposed to achieve a superior tradeoff between them in this paper. The peak value of the inductor current can be decreased as well. Its control parameter is easy to choose. When compared with the conventional control methods, the proposed control shows a better dynamic performance. Experimental results, which are in agreement with the theoretical analysis, are provided to verify the proposed control method.

• 전력전자학회논문지
• /
• 제13권2호
• /
• pp.79-87
• /
• 2008

연료전지의 낮고 변동폭이 큰 전압을 안정된 높은 전압으로 승압시키기 위하여 부스트 컨버터가 사용되고 있다. 전기적인 절연이 요구되지 않는 응용에서는 손실, 가격 및 부피 상승의 원인이 되는 고주파 변압기가 없는 무변압기형의 부스트 컨버터가 장점을 갖는다. 본 논문에서는 새로운 무변압기형 부스트 컨버터를 제안한다. 제안한 컨버터는 $6{\sim}8$배의 실제 사용가능 한 승압비를 가지며 입 출력 전류 리플이 매우 작아 연료전지 응용에 적합하다. 이에 대한 이론적 해석과 시뮬레이션 및 실험파형을 통해 타당성을 검증하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.212-216
• /
• 2001

Because conventional switching converters have been usually using unbalanced circuit topologies, parasitic capacitance between the drain/collector of an active switch and the frame ground through its heat sink may generate the common-mode conducted noise. We have proposed a balanced switching converter circuit, which is an effective way to reduce the common-mode conducted noise. As an example, a boost converter version of the balanced switching converter was presented and the mechanism of the common-mode noise reduction was explained using equivalent circuits. This paper extends the concept of the balanced switching converter circuit and presents a buck-boost converter version of the balanced switching converter. The feature of common-mode noise reduction is confirmed by experimental results and the mechanism of the common-mode noise reduction is explained using equivalent circuits.

• Journal of Electrical Engineering and Technology
• /
• 제6권4호
• /
• pp.519-526
• /
• 2011

An investigation of the mechanism of period-doubling bifurcation in a voltage mode controlled buck-boost converter operating in discontinuous conduction mode is conducted from the viewpoint of nonlinear dynamical systems. The discrete iterative model describing the dynamics of the close-loop is derived. Period-doubling bifurcation occurs at certain values of the feedback factor. Results from numerical simulations and experiments are provided to verify the evolution of perioddoubling bifurcation, and the results are consistent with the theoretical analysis. These results show that the buck-boost converters exhibit a wide range of nonlinear behavior, and the system exhibits a typical period-doubling bifurcation route to chaos under particular operating conditions.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.815-818
• /
• 2004

The emerging applications such as reliable back-up power system and renewable energy call for high boost U-n converter. The conventional topologies to get high output voltage are using flyback circuit, cascade converters, and coupled inductor DC-DC converter. They have the stress and loss related to the leakage energy which results in low efficiency Tn this paper, novel high boost converter is presented. It has a structure of cascade boost converter but only one switch. Therefore, drive circuit is simple and extreme duty ratio is eliminated. To verify the proposed circuit, theoretical analysis and experimental results has been done using a prototype power supply.