• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.88-91
• /
• 2004

It is generally known that the bonding strength of RC(Reinforced Concrete) flexural members strengthened by fiber sheet composites are sufficient and the bonding failure does not occur until the sheet failed. However, many researchers have been reported that, before the failure of the sheet, the bonding failure happens even though the bonding length is sufficient. This study was carried out to evaluate the effectiveness of shear key and U strip on flexural behavior of reinforced concrete beam structures. The ply number of CFS(Carbon Fiber Sheet), location of shear key, and existence or not of U strip were selected as the main test variables. Test results show that the behavior of a beam of which shear key is located in the nearby. of support and U strip is not existent, and having CFS of 1 ply is mostly improved.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.273-278
• /
• 1998

In this paper, basic micro-mechanical properties of unidirectional CFRP composite shell such as bonding strength, fiber volume fraction and void fraction are measured and tensile strength test is performed with a fixture. And then fracture surfaces are observed by SEM. In case of basic micro-mechanical properties, bonding strength is reduce with decreasing of radius of each ply in a shell for the effect of residual stress, fiber volume fraction is smaller than plate, and void fraction is vise versa. For these reason, tensile strength of shell is smaller than plate fabricated with same prepreg. For failure mode shell has many splitted part along its length, and it is assumed that this phenomenon is caused by the difference of bonding strength for residual stress.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.423-426
• /
• 2006

Paper has fibers and fines network structure and it is strongly affected by interface bonding between fibers. Depending on the inter-fiber bonding, paper bulk is determined. Fines play an important roll in Campbell and consolidation effect through wet pressing and drying operations. Refined Sw-BKP, Hw-BKP and BCTMP fines were used to investigate the fines effect. Wet-web strength, breaking length, scattering coefficient, and hydrodynamic specific volume were measured. According to the result of experiments, chemical and morphological compositions of fines do not strongly affect to wet-web forming, but strongly affect to drying operations which form hydrogen bonding among fiber-fines-fiber matrixes. Paper bulk should be controlled by the extent of hydrogen bonding between fibers during drying operations.

• 펄프종이기술
• /
• 제37권2호
• /
• pp.64-69
• /
• 2005

Suitability of corrugating medium for microflute shape formation was analyzed in terms of fiber bonding strength and paper stiffness. Cationic starch and oxidized starch were applied to corrugating medium's surface by bar coater in order to compare the relative importance of stiffness and fiber bonding on microflute formation. It was found that cationic starch was beneficial for better stiffness and oxidized starch was beneficial for better fiber bonding. The results of the decreasing ratio of length by flute formation, the calculated conditioning effect, and the flute height before and after conditioning treatment were obtained. For better microflute shape formation and its preservation it was found that fiber bonding strength should be increased, proper stiffness was required, and resistance to water absorption from surroundings should be increased.

• 접착 및 계면
• /
• 제3권1호
• /
• pp.37-42
• /
• 2002

Adhesives are becoming increasingly accepted for advanced engineering/boding tasks. Therefore the understanding of the basic principles and the benefits of elastic bonding and structural bonding respectively is of utmost importance. Structural bonding means adhesive performance in load-bearing environments. Furthermore. the time to achieve handling strength has an impact on the economics of an assembly line. The paper gives briefly a summary about the fundamentals of elastic bonding and discusses different adhesive systems in the context of handling strength. Hereby the focus lies on the Warm Melt Technology, and its potential is compared to standard adhesives (l-part, 2-part and Booster Technology, a special 2-C system). Examples illustrate their economical benefits. Main Points : ${\bullet}$ The basic principles and benefits of elastic bonding ${\bullet}$ Warm-melt Technology in comparison with standard adhesives ${\bullet}$ Handling strength an economic issue ${\bullet}$ Combination with Booster-Technology, a special 2-C PUR system ${\bullet}$ Presentation of real world applications Learning Objectives: ${\bullet}$ Fundamentals of elastic bonding ${\bullet}$ Warm-melt Technology: correlation between chain length and cristallinity ${\bullet}$ Handling strength and curing speed of various systems in comparison ${\bullet}$ Real world applications illustrate the potential of the Warm-melt Technology.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권5호
• /
• pp.149-156
• /
• 2021

FRP 보강근은 철근-콘크리트 부재의 부식 문제를 해결하기 위해 제안되어왔으나, FRP는 높은 인장강도, 낮은 연성 및 선형 탄성 거동으로 인해 하중이 전달될 때 콘크리트와 보강재 사이의 부착 메커니즘이 다르다. 그러므로, FRP-Rebar와 콘크리트 사이의 부착 거동은 주의 깊게 검토해야 한다. 이를 위해 직접 인발 실험이 간단하게 부착 거동을 평가할 수 있으므로 사용됐으나, 직접인발의 실험 결과는 실제 FRP를 보강근으로 사용한 콘크리트 부재의 휨-부착 거동과 다르다. 그러므로 실제 휨-부착 거동을 평가할 방안이 필요하다. 본 연구에서는 FRP를 보강근으로 사용한 콘크리트 부재의 휨-부착 거동에 대한 평가방법을 검토하고 비교하였다. 그 결과, 겹침이음이 있는 부재의 실험 방법이 실제 휨-부착 특성을 잘 반영할 수 있으나 다른 실험방법보다 시험체의 단면 및 지간이 커야 하고 시험체의 설계 및 해석이 복잡하다. 한편, 아치가 있는 부재 실험은 모멘트 팔길이의 변화를 무시하는 평형 방정식을 기반으로 한 힌지가 있는 부재 실험과 달리 콘크리트의 영향을 반영할 수 있으나, 휨-부착에 의한 파괴 이전에 전단파괴의 우려가 있다.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.1-18
• /
• 2010

Bonding of carbon fiber reinforced polymer (CFRP) composites has become a popular technique for strengthening concrete structures in recent years. The bond stress between concrete and CFRP is the main factor determining the strength, rigidity, failure mode and behavior of a reinforced concrete member strengthened with CFRP. The accurate evaluation of the strain is required for analytical calculations and design processes. In this study, the strain between concrete and bonded CFRP sheets across the notch is tested. In this paper, indirect axial tension is applied to CFRP bonded test specimen by a four point bending tests. The variables studied in this research are CFRP sheet width, bond length and the concrete compression strength. Furthermore, the effect of a crack- modeled as a notch- on the strain distribution is studied. It is observed that the strain in the CFRP to concrete interface reaches its maximum values near the crack tips. It is also observed that extending the CFRP sheet more than to a certain length does not affect the strength and the strain distribution of the bonding. The stress distribution obtained from experiments are compared to Chen and Teng's (2001) analytical model.

• 접착 및 계면
• /
• 제4권2호
• /
• pp.21-29
• /
• 2003

Hot AC anodising has been evaluated us pre-treatment for aluminium prior to structural adhesive bonding. Phosphoric and sulphuric acid hot AC anodising showed very promising adhesion promoter capabilities with durability comparable with the best standard DC anodising procedures. AC anodising does not required etching prior to anodising and offers u pre-treatment time down to 20 seconds. The interface/interphase between the aluminium substrate and the adhesive was investigated in order to get a better understanding of the involved adhesion mechanisms and to explain the long-tenn properties. The alkaline medium formed at the oxide layer/adhesive interface has been shown to induce a partial dissolution of the oxide layer leading to the formation of metallic ions which diffuse in the adhesive (EPMA measurements). The effect of diffusion of the Al ions on adhesion and joint durability is still uncertain but studies showed that pre-bond moisture affected the joints durability and to some extent the diffusion length. specially for DC anodised samples. So far no direct correlation could be established between the diffusion length d and the joints durability but new trials with better control over the elapsed time between bonding and adhesive curing are expected to help getting a better understanding of the involved mechanisms.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권6호
• /
• pp.533-540
• /
• 1997

The microwave dielectric properties of ((P $b_{1-x}$ C $a_{x}$)Zr $O_3$ and (P $b_{0.63}$,C $a_{0.37-x}$ $M_{x}$)Zr $O_3$(M=Mg,Sr) ceramics were investigated. In (P $b_{1-x}$ C $a_{x}$)Zr $O_3$ (X=0.33~0.40) ceramics, high quality factor and small temperature coefficient of resonant frequency were obtain in (P $b_{0.63}$C $a_{0.37}$)Zr $O_3$with perovskite structure. In the case of (P $b_{0.63}$C $a_{0.37-x}$M $g_{x}$)Zr $O_3$ dielectric constant temperature coefficient of resonant frequency increased and quality factor decreased due to increase of polarization of A-O bonding. When replacing Ca ion with Sr ion with large ion radius, polarization decreased with increased of bonding length and thus dielectric constant and temperature coefficient of resonant frequency decreased.decreased.creased.

• Composites Research
• /
• 제33권6호
• /
• pp.371-376
• /
• 2020

접착강도는 표면처리 기술을 통해 향상시킬 수 있다. 가장 일반적인 방법은 기계적인 결합력을 향상시킬 수 있는 접착 표면의 변화이다. 본 연구는 접착면의 레이저 표면 처리가 기계적 결합력에 미치는 영향과 탄소섬유 강화 복합재료(CFRP)의 접착 결합에 대해 설명한다. 1064 nm의 레이저를 활용하여 표면 조도를 패턴화했다. 레이저 샷의 수, 패턴의 방향, 길이가 CFRP/CFRP 단일 조인트의 접착력에 미치는 영향을 인장 시험을 통해 조사했다. ASTM D5868에 따른 시험을 수행하였으며, 파단 후 손상된 표면을 분석하여 결합 메커니즘을 결정했다. 접착 강도의 증가를 위해서는 CFRP 표면에 최적화된 레이저 샷의 수와 조도 깊이가 구성되어야 한다. 인장방향에서의 전단응력을 고려할 때, 접착층의 파단 경로를 길어지게 하는 45°의 방향의 조도가 접착강도의 증가를 야기했다. 그러나 레이저에 의한 조도의 길이는 접착 강도에 크게 영향을 주지 못했다. 레이저를 이용한 접착면의 표면처리는 기계적 결합 메커니즘을 확보하고 CFRP 접착 조인트의 접착 강도를 향상시키는 적합한 방법이라는 결론을 도출할 수 있다. 레이저 처리를 이용한 이점을 완전히 이용하기 위해서는 최적화된 레이저 공정 변수에 대한 연구가 반드시 필요하다.