• 한국도로학회논문집
• /
• 제3권4호
• /
• pp.117-126
• /
• 2001

본 연구는 일반 콘크리트와 SBR 라텍스 개질 콘크리트의 부착강도 특성을 분석하고자 신 구 콘크리트로 구성된 직접인장 시험체를 제작하여 부착강도를 측정하였다. 이때, 시험체와 측정기의 연결장치가 $360^{\circ}$ 회전이 가능하도록 시험장비를 개선하여 시험체의 편심이 부착강도 측정에 미치는 영향을 최소화였다. 주요 실험변수로는 라텍스 혼입율, 표면 처리상태, 표면 함수상태로 정하였으며 실험결과는 다음과 같다; 라텍스 혼입률이 증가함에 따라 부착강도도 증가하였으며, 혼입률 15%에서 37%의 증진을 보였다. 이것은 라텍스가 골재와 시멘트 페이스트 사이에 충전되어 필름 막을 형성하고 부착력을 증진시켰기 때문인 것으로 판단된다. 표면처리에 따라 부착강도의 변화를 고찰한 결과, 샌드 그라인딩과 와이어 부러쉬에 의해 표면처리를 하였을 경우 부착강도는 단순 절단한 경우보다 약 49% 증가하였다. 표면함수 상태에 따른 영향을 고찰한 결과, 부착강도는 기존 콘크리트 표면이 건조하였을 경우에 가장 작게 나타났고, 자유수가 표면에 있을 때가 그 다음을 나타냈으며, 표면건조포화상태에선 37% 증가하여 가장 크게 나타났다. 따라서 부착강도를 증진시키기 위해서는 적절한 표면처리와 표면함수상태의 유지가 필수적임을 알 수 있었다.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.245-265
• /
• 1991

The purpose of this study was to observe the changes of the elemental transmission and bond strength between the metal and porcelain according to various kinds of ion beam mixing method. ion beam mixing of $meta1/SiO_2$ (silica), $meta1/Al_2O_3$(alumina) interfaces causes reactions when the $Ar^+$ was implanted into bilayer thin films using a 100KeV accelerator which was designed and constructed for this study. A vacuum evaporator used in the $10^{-5}-10^{-6}$ Torr vacuum states for the evaporation. For this study, three kinds of porcelain metal selected, -precious, semiprecious, and non-precious. Silica and alumina were deposited to the metal by the vacuum evaporator, separately. One group was treated by two kinds of dose of the ion beam mixing $(1\times10^{16}ions/cm^2,\;5\times10^{15}ions/cm^2)$, and the other group was not mixed, and analyzed the effects of ion beam mixing. The analyses of bond strength, elemental transmissions were performed by the electron spectroscopy of chemical analysis (ESCA), light and scanning electron microscope, scratch test, and micro Vickers hardness tests. The finding led to the following conclusions. 1. In the scanning electron and light microscopic views, ion beam mixed specimens showed the ion beam mixed indentation. 2. In the micro Vickers hardness and scratch tests, ion beam mixed specimens showed higher strength than that of non mixed specimens, however, nonprecious metal showed a little change in the bond strength between mixed and non mixed specimens. 3. In the scratch test, ion beam mixed specimens showed higher shear strength than that of non treated specimens at the precious and semiprecious groups. 4. In the ESCA analysis, Au-O and Au-Si compounds were formed and transmission of the Au peak was found ion beam mixed $SiO_2/Au$ specimen, simultaneously, in the higher and lower bonded areas, and ion beam mixed $SiO_2/Ni-Cr$ specimen, oxygen, that was transmitted from $SiO_2\;to\;SiO_2/Ni-Cr$ interface combined with 12% of Ni at the interface.

• 콘크리트학회논문집
• /
• 제22권5호
• /
• pp.609-616
• /
• 2010

FRP-콘크리트 합성 바닥판은 압축에 강한 콘크리트를 상부에 위치시키고 인장에 강한 FRP를 하부에 위치시켜, FRP와 콘크리트가 갖는 장점을 극대화시킴으로서 내구성, 안전성 등을 두루 향상시킨 새로운 개념의 구조이다. 그러나 서로 다른 재질의 두 재료를 합성시키기 위한 방안으로서 연구 초기에 적용된 규사코팅 공법 외에 수직부착력을 향상시킬 수 있는 기계적 합성 방안을 고안하였다. 이렇게 고안한 합성 방안이 적용된 실제 사이즈의 바닥판 실험체를 제작하여 정적 및 피로반복실험을 수행하였다. 정적실험 결과 이 연구에서 제안한 합성 방안이 적용된 바닥판이 처짐 및 균열 등에 대해서 설계기준을 충분히 만족시켜 매우 우수한 성능을 나타내고 있었으며, 피로실험 결과 파괴하중의 50%로 200만회 가력한 후에도 처짐 및 균열 등에 대해 설계기준을 만족하고 있어 충분한 피로내구성을 확보하고 있는 것으로 나타났다. 이에 이 연구에서 제시한 규사코팅과 기계적 합성 방안을 동시에 적용한 합성 방안은 FRP-콘크리트 합성 바닥판에 대해 충분한 적용성을 갖고 있으며, FRP-콘크리트 합성 바닥판 설계시 제시한 설계조건들이 적절하게 이용될 수 있음을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.835-841
• /
• 2013

Modern solid-state gyroscopes (HRG) with hemispherical resonators from high-purity quartz glass and special surface superfinishing and ultrathin gold coating become the best instruments for precise-grade inertial reference units (IRU) targeting long-term space missions. Designing of these sensors could be a notable contribution into development of Korea as a space nation. In participial, 40mm diameter thin-shell resonator from high-purity fused quartz, fabricated as a single-piece with its supporting stem has been designed, machined, etched, tuned, tested, and delivered by STM Co. (ATS of Ukraine) several years ago; an extremely-high Q-factor (upto 10~20 millions) has been shown. Understanding of the best way how to match such a unique sensor with inner glass assembly of the gyro means how to use the high potential in a maximal extent; and this has become the urgent task. Inner quartz glass assembly has a very thin indium (In) layer soldered the resonator and its silica base (case), but effects of internal resonances between operational modal pair of the shell-cup and its side (parasitic) modes can notable degrade the potential of the sensor as a whole, instead of so low level of resonator's intrinsic losses. Unfortunately, there are special combinations of dimensions of the parts (so-called, "resonant sizes"), when intensive losses of energy occurs. The authors proposed to use the length of stem's fixture as an additional design parameter to avoid such cases. So-called, a cyclic scheme of finite element method (FEM) and ANSYS software were employed to estimate different combinations of gyro assembly parameters. This variant has no mismatches of numerical origin due to FEM's discrete mesh. The optimum length and dangerous "resonant lengths" have been found. The special attention has been paid to analyses of 3D effects in a cup-stem transient zone, including determination of a difference between the positions of geometrical Pole of the resonant hemisphere and of its "dynamical Pole", i.e., its real zone of oscillation node. Boundary effects between the shell (cup) and 3D short "beams" (inner and outer stems) have been ranged. The results of the numerical experiments have been compared with the classic model of a quasi-hemispherical shell band with inextensional midsurface, and the solution using Rayleigh's functions of the $1^{st}$ and $2^{nd}$ kinds. To guarantee the truth of the recommended sizes to a designer of the real device, the analytical and FEM results have been compared with experimental data for a party of real resonators. The consistency of the results obtained by different means has been shown with errors less than 5%. The results notably differ from the data published earlier by different researchers.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.77-77
• /
• 1998

Present silicon dioxide (SiOz) 떠m as intennetal dielectridIMD) layers will result in high parasitic c capacitance and crosstalk interference in 비gh density devices. Low dielectric materials such as f f1uorina뼈 silicon oxide(SiOF) and f1uoropolymer IMD layers have been tried to s이ve this problem. I In the SiOF ftlm, as fluorine concentration increases the dielectric constant of t뼈 film decreases but i it becomes unstable and wa않r absorptivity increases. The dielectric constant above 3.0 is obtain어 i in these ftlms. Fluoropolymers such as polyte$\sigma$따luoroethylene(PTFE) are known as low dielectric c constant (>2.0) materials. However, their $\alpha$)Or thermal stability and low adhesive fa$\pi$e have h hindered 야1리ru뚱 as IMD ma따"ials. 1 The concept of a plasma processing a찌Jaratus with 비gh density plasma at low pressure has r received much attention for deposition because films made in these plasma reactors have many a advantages such as go여 film quality and gap filling profile. High ion flux with low ion energy in m the high density plasma make the low contamination and go어 $\sigma$'Oss피lked ftlm. Especially the h helicon plasma reactor have attractive features for ftlm deposition 야~au똥 of i앙 high density plasma p production compared with other conventional type plasma soun:es. I In this pa야Jr, we present the results on the low dielectric constant fluorocarbonated-SiOF film d밑JOsited on p-Si(loo) 5 inch silicon substrates with 00% of 0dFTES gas mixture and 20% of Ar g gas in a helicon plasma reactor. High density 띠asma is generated in the conventional helicon p plasma soun:e with Nagoya type ill antenna, 5-15 MHz and 1 kW RF power, 700 Gauss of m magnetic field, and 1.5 mTorr of pressure. The electron density and temperature of the 0dFTES d discharge are measUI벼 by Langmuir probe. The relative density of radicals are measured by optic허 e emission spe따'Oscopy(OES). Chemical bonding structure 3I피 atomic concentration 따'C characterized u using fourier transform infrared(FTIR) s야3띠"Oscopy and X -ray photonelectron spl:’따'Oscopy (XPS). D Dielectric constant is measured using a metal insulator semiconductor (MIS;AVO.4 $\mu$ m thick f fIlmlp-SD s$\sigma$ucture. A chemical stoichiome$\sigma$y of 야Ie fluorocarbina$textsc{k}$영-SiOF film 따~si야영 at room temperature, which t the flow rate of Oz and FTES gas is Isccm and 6sccm, res야~tvely, is form려 야Ie SiouFo.36Co.14. A d dielec$\sigma$ic constant of this fIlm is 2.8, but the s$\alpha$'!Cimen at annealed 5OOt: is obtain려 3.24, and the s stepcoverage in the 0.4 $\mu$ m and 0.5 $\mu$ m pattern 킹'C above 92% and 91% without void, res야~tively. res야~tively.

• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.656-669
• /
• 1998

Hydrogen peroxide at high concentration during walking bleaching may cause damage to the tooth structure and to the surrounding periodontal tissues and may develop external root resorption. Clinically, It is so important to find a method of prevention or minimization of these complications. The efficacy of various chamber-irrigating agents to eliminate residual hydrogen peroxide after walking bleaching was examined and compared with water rinse in this study. Extracted human 46 premolars without any cementoenamel junction defects were treated endodontically and based with IRM to 1 mm below CEJ and totally bleached 3 times for each tooth with 30% hydrogen peroxide and sodium perborate. Upon completion of the 3rd walking bleaching procedure, the cervical portion and pulp chamber of each group of teeth were irrigated with catalase, 70% ethylalcohol, acetone, and distilled water. And then, a radicular hydrogen peroxide penetration was measured with spectrophotometer immediately after each bleaching and following treatment with each chamber-irrigating agents, and the significance of their eliminating efficacy of residual hydrogen peroxide was analyzed by Kruskal-Wallis test. The results were obtained as follows. 1. Cervical root penetration of hydrogen peroxide was increased as the bleaching procedure was repeated(P<.01). 2. The most effective irrigant that removed residual hydrogen peroxide was the catalase, and the least effective one was water rinsing (P<.01).; there was no significant difference between the acetone and ethanol group. 3. The Irrigation with antioxidant enzyme or water-displacement solutions can eliminate residual oxygen radicals from the pulp chamber effectively after walking bleaching. So, these agents can reduce adverse effects such as cervical external resorption and periapical inflammation and prevent residual $O_2$ from impeding composite resin polymerization, thus increase the bonding strength of composite resin. This, in turn reduces microleakage and discoloration of the esthetic restoration, extending its service-life.

• 대한치과보철학회지
• /
• 제45권5호
• /
• pp.601-610
• /
• 2007

Statement of problem: The adhesion between titanium and ceramic is less optimal than conventional metal-ceramic bonding, due to reaction layer form on cast titanium surface during porcelain firing. Purpose: This study characterized the effect of titanium-ceramic adhesion after gold and TiN coating on cast and wrought titanium substrates. Material and method: Six groups of ASTM grade II commercially pure titanium and cast titanium specimens$(13mm{\times}13mm{\times}1mm)$ were prepared(n=8). The conventional Au-Pd-In alloy served as the control. All specimens were sandblasted with $110{\mu}m\;Al_2O_3$ particles and ultrasonically cleaned for 5min in deionized water and dried in air before porcelain firing. An ultra-low-fusing dental porcelain (Vita Titankeramik) was fused on titanium surfaces. Porcelain was debonded by a biaxial flexure test at a cross head speed of 0.25mm/min. The excellent titanium-ceramic adherence was exhibited by the presence of a dentin porcelain layer on the specimen surface after the biaxial flexure test. Area fraction of adherent porcelain (AFAP) was determined by SEM/EDS. Numerical results were statistically analyzed by one-way ANOVA and Student-Newman-Keuls test at ${\alpha}=0.05$. Results: The AFAP value of cast titanium was greatest in the group 2 with TiN coating, followed by group 1 with Au coating and the group 3 with $Al_2O_3$ sandblasting. Significant statistical difference was found between the group 1, 2 and the group 3 (p<.05). The AFAP value of wrought titanium was greatest in the group 5 with TiN coating, followed by the group 4 with Au coating and the group 6 with $Al_2O_3$ sandblasting. Conclusion: No significant difference was observed among the three groups (p>.05). The AFAP values of the cast titanium and the wrought titanium were similar. However the group treated with $Al_2O_3$ sandblasting showed significantly lower value (p<.05).

• 대한화학회지
• /
• 제33권3호
• /
• pp.287-294
• /
• 1989

미국 EPA가 주요 유기오염물질로 정한 페놀류들에 대하여 역상 액체 크로마토그래피에서 혼합용액을 등용매 용리법으로 완전히 분리할 수 있는 최적 분리조건과 머무름 거동을 조사하였다. 이때 정지상은 ${\mu}$-Bondapak C18 컬럼을, 이동상은 메탄올-물, 아세토니트릴-물, THF-물을 사용하였다. Statistical simplex system의 삼각형에서 각 조건에서의 크로마토그램을 얻어 COF 값을 비교해 본 결과 메탄올 : 아세토니트릴 : 물의 비율이 7 : 40 : 53 부근에서 가장 분리가 잘 됨을 알았다. 여러가지 물리적 파라미터를 고려하여 폐놀류들의 머무름 거동을 조사한 결과 엔탈피가 증가함에 따라 머무름이 감소하였다. 단, 극성이 큰 치환기를 갖는 경우에는 엔탈피 효과보다 그 시료의 극성도가 머무름에 더 많은 영향을 미치었다. 또한 분배계수로부터 유도된 치환기 상수와 머무름과의 상관관계를 알아본 결과 메탄올 - 물, 아세토니트릴 - 물을 이동상으로 사용한 경우는 페놀류들의 머무름이 분배 메카니즘에 따음을 확인할수 있었다. 그러나 THF-물을 사용한 경우는 이동상의 영향이 크게 작용하여 상관관계가 감소하였다. 소수성을 나타내는 van der Waals 부피와 함께 pi-에너지 효과와 수소결합에너지 효과를 같이 고려하여 머무름 거동을 조사한 결과 이동상으로 아세토니트릴 - 물을 사용한 경우 상관계수 0.9927를 갖는 다음의 직선식을 얻었다. $log^{k'}=2.515{\times}10^{-2}VWV-1.301{\times}10^{-1}E-3.674{\times}10^{-1}$

• Macromolecular Research
• /
• 제10권3호
• /
• pp.158-167
• /
• 2002

In order to endow with new bioactive functionality from small intestine submucosa (SIS) powder as natural source to poly (L-lactide) (PLA) and poly (lactide-co-glycolide) (PLGA) synthetic biodegradable polymer, porous SIS/PLA and SIS/PLGA as natural/synthetic composite scaffolds were prepared by means of the solvent casting/salt leaching methods for the possibility of the application of tissue engineered bone and cartilage. A uniform distribution of good interconnected pores from the surface to core region was observed the pore size of 40~500 ${\mu}{\textrm}{m}$ independent with SIS amount using the solvent casting/salt leaching method. Porosities, specific pore areas as well as pore size distribution also were almost same. After the fabrication of SIS/PLA hybrid scaffolds, the wetting properties was greatly enhanced resulting in more uniform cell seeding and distribution. Five groups as PGA non-woven mesh without glutaraldehyde (GA) treatment, PLA scaffold without or with GA treatment, and SIS/PLA (Code No.3 ; 1 : 12 of salt content, (0.4 : 1 of SIS content, and 144 ${\mu}{\textrm}{m}$ of median pore size) without or with GA treatment were implanted into the back of nude mouse to observe the effect of SIS on the induction of cells proliferation by hematoxylin and eosin, and von Kossa staining for 8 weeks. It was observed that the effect of SIS/PLA scaffolds with GA treatment on bone induction are stronger than PLA scaffolds, that is to say, in the order of PLA/SIS scaffolds with GA treatment > PLA/SIS scaffolds without GA treatment > PGA nonwoven > PLA scaffolds only with GA treatment = PLA scaffolds only without GA treatment for the osteoinduction activity. The possible explanations are (1) many kinds of secreted, circulating, and extracellular matrix-bound growth factors from SIS to significantly affect critical processes of tissue development and differentiation, (2) the exposure of SIS to GA resulted in significantly calcification, and (3) peri-implant fibrosis due to covalent bonding between collagen molecule by crosslinking reaction. In conclusion, it seems that SIS plays an important role for bone induction in SIS/PLA scaffolds for the application of tissue engineering area.

• 접착 및 계면
• /
• 제16권2호
• /
• pp.69-75
• /
• 2015

돌침대에 사용되는 석재의 무게를 줄여 경량화를 추구하려면 석재의 두께를 줄이고 보강재료로 석재의 강도를 유지해야 한다. 본 연구에서는 돌침대용 석재/목재 보드 개발에 대한 연구를 진행하였다. 돌침대에 삽입될 돌의 무게를 줄이기 위해 석재와 목재를 접합하였다. 목재의 강도 향상과 표면개질을 위하여 열처리 조건에 따른 목재의 물성변화를 관찰하였다. 대기 조건에서 열처리한 목재의 경우 고온의 온도에 따라 목재의 강성이 높아졌다. 열처리 최적조건은 표면에너지와 인장, 굴곡 강도변화 경향을 바탕으로 $100^{\circ}C$ 조건임을 확인하였다. 석재와 목재간 높은 접착력을 확보하기 위해 최적의 접착제 조성을 연구하였다. 아민계 에폭시 접착제, 폴리우레탄(PU)계 접착제, 염화고무계(CR) 접착제 마지막으로 염화비닐초산계 접착제에 따른 석재와 목재간 랩 전단실험을 진행하였다. 랩 전단 실험 후 파단면을 관찰해볼 때 에폭시 접착제를 이용할 때 목재 기지의 인열 파괴가 발생되었다. 접착면에서의 전단력이 목재 자체의 파괴 강도보다 높다는 결과를 바탕으로 최적의 접착제 조건이 에폭시계 접착제임을 확인할 수 있었다.