• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.3
• /
• pp.33-39
• /
• 1992

This paper presents a summary of the immersion ultrasonic test to analyze the quality of diffusion bonding parts. The most important property of diffusion bonding parts is bonding strength, and that can be obtained by shear test. By comparing among data obtained by ultrasonic test(C-Scan) and those by shear test (bonding strength), these data are shown to be in good relation. Therefore ultrasonic C-Scan test result can be used successfully in quantitative quality control for diffusion bonded parts.

• Geomechanics and Engineering
• /
• v.18 no.5
• /
• pp.555-566
• /
• 2019

The purpose of this paper is to investigate the thermal effects on the behaviour reinforced-concrete beams strengthened by bonded angle-ply laminated composites laminates plate $[{\pm}{\theta}n/90m]_S$. Effects of number of $90^{\circ}$ layers and number of ${\pm}{\theta}$ layers on the distributions of interfacial stress in concrete beams reinforced with composite plates have also been studied. The present results represent a simple theoretical model to estimate shear and normal stresses. The effects the temperature, mechanical properties of the fibre orientation angle of the outer layers, the number of cross-ply layers, plate length of the strengthened beam region and adhesive layer thickness on the interfacial shear and normal stresses are investigated and discussed.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.218-225
• /
• 2013

The densification behavior and strength of sintered reaction bonded silicon nitrides (SRBSN) that contain $Lu_2O_3-SiO_2$ additives were improved by the addition of fine Si powder. Dense specimens (relative density: 99.5%) were obtained by gas-pressure sintering (GPS) at $1850^{\circ}C$ through the addition of fine Si. In contrast, the densification of conventional specimens did not complete at $1950^{\circ}C$. The fine Si decreased the onset temperature of shrinkage and increased the shrinkage rate because the additive helped the compaction of green bodies and induced the formation of fine $Si_3N_4$ particles after nitridation and sintering at and above $1600^{\circ}C$. The amount of residual $SiO_2$ within the specimens was not strongly affected by adding fine Si powder because most of the $SiO_2$ layer that had formed on the fine Si particles decomposed during nitridation. The maximum strength and fracture toughness of the specimens were 991 MPa and $8.0MPa{\cdot}m^{1/2}$, respectively.

• Korean Journal of Metals and Materials
• /
• v.49 no.5
• /
• pp.380-387
• /
• 2011

Wire brushing, which is a typical surface preparation method for roll bonding, has recently been highlighted as a potentially effective method for surface nanocrystallization. In the present study, the microstructure evolution and hardness of the wire-brushed surface and roll-bonded interface of a 1050 aluminum sheet were investigated. Wire brushing formed protruded layers with a nanocrystalline structure and extremely high surface hardness. After roll bonding, the protruded layers remained as hard layers at the interface. Due to their hardness and brittleness the interface hard layers, can affect the interface bonding properties and also play an important role determining the mechanical properties of multi-layered clad sheets.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.159-159
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.05a
• /
• pp.145-145
• /
• 2001

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05a
• /
• pp.111-111
• /
• 1992

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.140.2-140
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.75-75
• /
• 1994

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.85.1-85.1
• /
• 2007