• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.1
• /
• pp.51-60
• /
• 1991

The aim of this study is to investigate the heat transfer characteristics in the transient cooling process of a high temperature wall. The slow transient cooling experiment was carried out with a copper block of high thermal capacity. The results of these experiments are as follows. 1. Temperature histories measured by the thermocouple, which is 0.99, 2.00, 2.99mm from the heat transfer surface showed monotonous during the cooling process. These variation are the curves of typical temperature histories in film-boiling, transition-boiling, and nucleate-boiling regions. 2. The temperature histories were measured by thermocouple installed in the copper block. The variations of the surface heat fluxes and surface temperature were computed from the numerical solution method TDMA from the measured temperature histories for radial position one dimensional heat transfer inverse problem. The boiling curves were found by the computed temperature histories. 3. The rewetting point which starts to change from film boiling to nucleate boiling is not connected with the mass velocity and it were found that the temperature of rewetting point indicated about $100^{\circ}C$. 4. The heat flux of rewetting point was about $10^5Kcal/m^2h$, at that time, the heat transfer coeficient indicated about $1000Kcal/m^2h^{\circ}C$ irrelevent to mass velocity. 5. The wall superheat decreases as the pressure increases. But I found that rewetting point appeared under higher condition in the wall temperature.

• Journal of the Korean Society of Safety
• /
• v.35 no.5
• /
• pp.128-136
• /
• 2020

In the present experimental study, the effect of water-based iron(III) oxide nanofluid on the MFB(Minimum Film Boiling) point during quenching was investigated. As the highly heated test specimen, the cylindrical stainless steel rod was used, and as the test fluids, the water-based iron(III) oxide nanofluids of 0.001 and 0.01 vol% concentrations were prepared with the pure water. To examine the effect of location in the test specimen, the thermocouples were installed at the bottom and middle of wall, and center in the test specimen. Through a series of experiments, the experimental data about the influences of nanofluid concentrations, the number of repeated experiments, and locations in the test specimen on the reaching time to MFB point, MFBT(Minimum Film Boiling Temperature), and MHF(Minimum Heat Flux) were obtained. As a result, with increasing the concentration of nanofluid and the number of repeated experiments, the reaching time to MFB point was reduced, but the MFBT and MHF were increased. In addition, it was found that the effect of water-based iron(III) oxide nanofluid on the MFB point at the bottom of wall in the test specimen was observed to be greater than that at the middle of wall and center. In the present experimental ranges, as compared with the pure water, the water-based iron(III) oxide nanofluid showed that the maximum reduction of reaching time to MFB point was about 53.6%, and the maximum enhancements of MFBT and MHF were about 31.1% and 73.4%, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.67-76
• /
• 2009

The development of a variety of methods like AM1, PM3, PM5 and DFT now allows the calculation of atomic and molecular properties with high precision as well as the treatment of large molecules with predictive power. In this paper, these methods have been used to calculate a number of quantum chemical descriptors (like Klopman atomic softness in terms of $E_n^{\ddag}\;and\;E_m^{\ddag}$, chemical hardness, global softness, electronegativity, chemical potential, electrophilicity index, heat of formation, total energy etc.) for 75 alkanes to predict their boiling point values. The 3D modeling, geometry optimization and semiempirical & DFT calculations of all the alkanes have been made with the help of CAChe software. The calculated quantum chemical descriptors have been correlated with observed boiling point by using multiple linear regression (MLR) analysis. The predicted values of boiling point are very close to the observed values. The values of correlation coefficient ($r^2$) and cross validation coefficient ($r_{cv}^2$) also indicates the generated QSPR models are valuable and the comparison of all the methods indicate that the DFT method is most reliable while the addition of Klopman atomic softness $E_n^{\ddag}$ in DFT method improves the result and provides best correlation.

• Korean Journal of Food Science and Technology
• /
• v.22 no.4
• /
• pp.486-491
• /
• 1990

To develop a new spice material garlic juice was prepared from peeled garlic and its composition, density and boiling point rise were investigated. Major components of the garlic juice were moisture(68.01%), crude protein(6.50%) and carbohydrate(25.39%). Yield of the juice from the peeled whole garlic was 49.50%(w/w). Density of the garlic juice with solid content of 32 to $65^{\circ}$ Brix was in the range of 1,107 to $1,243kg/m^3$. Boiling point rise of garlic juice increased exponentially with the increase of solid content. In the solid content range of 32 to $65^{\circ}$ Brix, the boiling point rise could be predicted with following experimental equation with average error of less than 7%. $$BPR=1.4105.\;P^{0.1338}.\;exp(0.0357.\;X_5-1.3925)$

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.119-126
• /
• 2016

In this study, we separated the lignin from the wood by using the high boiling point solvent for developing more environmental friendly pulping method. High boiling point solvents as Ethers, glycols and ketones were used to remove the lignin in the pine wood meals. The Yield and lignin content of residual wood meals was reduced according to the input of the catalyst. Me-C, E-Ca, TEG and MIBK had the best delignification rate of 9 kinds of high-boiling point solvents. At the hydrolysis ratio of the selected solvents, The TEG was highest remain ratio of carbohydrates and the E-Ca was lowest remain ratio of lignin. And the Me-C was most excellent lignin hydrolysis ratio at the low catalyst. The selectivity of delignification of Me-C, E-Ca, TEG and MIBK solvents were 49.6, 49.9, 53.8 and 53.1%, respectively, and its values were similar to those of the commercial Kraft Pulp.

• Solar Energy
• /
• v.19 no.2
• /
• pp.45-56
• /
• 1999

The performance of vertical and horizontal tubes with extended surface of rectangular and triangular cross section was investigated theoretically for boiling heat transfer. A simple method for numerical program assuming one-dimensional heat flow was used to predict the performance of these extended surface tubes. The object of this study was to predict the effects of the height, thickness, numbers and, clearance of the extended surface on boiling heat transfer. The results showed that extended surfaces are quite effective as compared to plane surfaces especially near the bum-out point and to promote heat flux in boiling heat transfer.

• Journal of The Korean Association For Science Education
• /
• v.33 no.7
• /
• pp.1385-1402
• /
• 2013

This study analyzes pre-service teachers' PCK dealing with visualization of the contents related to boiling point elevation and teaching methods in mock-lessons. As a result of analyzing pre-service teachers' knowledge based on PCK factors, most of the pre-service teachers accentuated on understanding boiling point elevation conceptually, whereas some of the others inclined to make students understand boiling point elevation in a scientific way, let the kids use numerical formulas to describe the concept, and motivate them to learn through the examples in real life. The pre-service teachers represented majority of the important facts of boiling point elevation as the knowledge required to understand things conceptually. However, they did not focus on improving the scientific thinking and inquiring levels of the students. Also, the pre-service teachers tended to teach at the level and order of the textbook. In some other cases, they considered the vocabularies and materials in the textbook (which could have been highlighted in the editing sequence) as the main topic to learn, or regarded the goal as giving students the ability to solve exercises in the textbook. It turned out that the pre-service teachers had a low level of knowledge of their students. It is recommended that they should make use of the materials given (such as data related to the misconception of students) during the training session. The knowledge of teaching and evaluating students was described superficially by the pre-service teachers; they merely mentioned the applications of models, such as the cyclic model and discovery learning, rather than thinking of a method related to the goals, or listed general assessment methods.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.35-40
• /
• 1992

A recently developed new technique for measuring the fraction of wetted area has applied to pool boiling of water. The basis of the new applied technique of ultrasonic makes use of the reflection of ultrasonic from the vapour surface to measure the fraction of wetted area values. The results are the measured fraction of wetted area values in nucleate and transition boiling and the pool boiling curve for water under steady state conditions. The measurement of this paper shows a fraction of wetted areaf around 0.98 at the critical heat flux for water.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.485-494
• /
• 2000

The purpose of this paper is to investigate a critical heat flux(CHF) during forced convective subcooled and saturated boiling in free water jet system impinged on a rectangular heated surface. The surface is supplied with subcooled or saturated water through a rectangular jet. Experimental parameters studied are a width of heated surface, a height of supplementary water and a degree of subcooling. Incipient boiling point is observed in the temperature of 6${\~}8^{\circ}C$ of superheat of test specimen. CHF depends on jet velocity for various boiling-involved coolant system. CHF also is proportional to the nozzle exit velocity to the power of n, where n is 0.55 and 0.8 for subcooled and saturated boiling, respectively. CHF is enhanced with a higher jet velocity, higher degree of subcooling and smaller width of a heated surface.

• Journal of the Korea Society for Simulation
• /
• v.4 no.1
• /
• pp.121-130
• /
• 1995

This paper deals with modeling and simulation of an industrial benzene-toluene-xylene plant. Because the fractionation unit of benzene-toluene-xylene plant has a narrow range of boiling point and doesn't have any sidecut and side reboiler, we employed boiling point estimation method in the modeling and simulation of the plant. Soave-Redlich-Kwong equation was used in the computation of thermodynamical properties. We solved resulting nonlinear equations by using Newton-Raphson method which is known to show fast convergence. Results of simulation showed good agreement with actual plant operation data.