• The Korean Journal of Ceramics
• /
• v.3 no.1
• /
• pp.43-46
• /
• 1997

Thulium (Tm) has been incorporated into $YAlO_3$ and $YTa_7O_{19}$ host materials to obtain blue phosphors. $Tm^{3+}$-doped $YAlO_3$ and $YTa_7O_{19}$ phosphors were prepared by the conventional solid state reaction method. According to the results of excitation and emission spectra measured at room temperature, the blue emission intensity of $Tm^{3+}$-doped $YTa_7O_{19}$, peaking at 455 nm was much higher than that of $Tm^{3+}-doped\; YAlO_34, peaking at 458 nm. The maximum of relative intensity of $Tm^{3+}-doped\; YAlO_3\; and\; YTa_7O_{19}$ was obtained at the doping concentration of 0.016 and 0.120 mol% $Tm^{3+}$, respectively. These emission spectra revealed the concentration quenching effect.

• Journal of Radiation Protection and Research
• /
• v.43 no.4
• /
• pp.160-169
• /
• 2018

Background: This study aims to develop an integrated optical system that can simultaneously or selectively measure the signals obtained from radioluminescence (RL), thermoluminescence (TL), and optically stimulated luminescence (OSL), which are luminescence phenomena of materials stimulated by radioactivity, heat, and light, respectively. The luminescence mechanism of various materials could be investigated using the glow curves of the luminescence materials. Materials and Methods: RL/TL/OSL integrated measuring system was equipped with a X-ray tube (50 kV, $200{\mu}A$) as an ionizing radiation source to irradiate the sample. The sample substrate was used as a heating source and was also designed to optically stimulate the sample material using various light sources, such as high luminous blue light emitting diode (LED) or laser. The system measured the luminescence intensity versus the amount of irradiation/stimulation on the sample for the purpose of measuring RL, TL and OSL sequentially or by selectively combining them. Optical filters were combined to minimize the interference of the stimulation light in the OSL signal. A long-pass filter (420 nm) was used for 470 nm LED, an ultraviolet-pass filter (260-390 nm) was used for detecting the luminescence of the sample by PM tube. Results and Discussion: The reliability of the system was evaluated using the RL/OSL characteristics of $Al_2O_3:C$ and the RL/TL characteristics of LiF:Mg,Cu,Si, which were used as dosimetry materials. The RL/OSL characteristics of $Al_2O_3:C$ showed relatively linear dose-response characteristics. The glow curve of LiF:Mg,Cu,Si also showed typical RL/OSL characteristics. Conclusion: The reliability of the proposed system was verified by sequentially measuring the RL characteristics of radiation as well as the TL and OSL characteristics by concurrent thermal and optical stimulations. In this study, we developed an integrated measurement system that measures the glow curves of RL/TL/OSL using universal USB-DAQs and the control program.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.11
• /
• pp.1020-1024
• /
• 2006

Europium$(Eu^{2+}\;or\;Eu^{3+})$-activated calcium aluminium silicate phosphors were synthesized for the first time and the structures and luminescence characteristics of these phosphors were investigated. The phosphors in this study emitted blue, green, and even red light depending on the starting milterials and annealing conditions for synthesis. In addition, the structure was also changed when the different starting materials were used. When $CaCO_3$ was used as a starting material, tetragonal $Ca_2Al_2SiO_7$ was formed. However, pure green light was emitted when the annealing was conducted in reduced atmosphere and red one was emitted by annealing in air. In the case of $CaSiO_3$ as a starting material, triclinic $CaAl_2Si_2O_8$ was formed and only pure blue emission was observed. Moreover, this blue phosphor exhibited higher intensity than that of commercial YAG:Ce phosphor, which showed the possibility of application on the phosphor for new light source such as a UV-LED.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.211-217
• /
• 2015

To fabricate white LED having a high color rendering index value, red color phosphor mixed with the green color phosphor together in the blue chip, namely the blue chips with RG phosphors packaging is most favorable for high power white LEDs. In our previous papers, we reported on successful syntheses of $Sr_{2-}$ $Si_5N_8:Eu^{2+}$ and $CaAlSiN_3$ phosphors for red phosphor. In this work, for high power green phosphor, greenemitting ternary nitride $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphor was synthesized in a high frequency induction furnace under $N_2$ gas atmosphere at temperatures up to $1400^{\circ}C$ using $EuF_3$ as a raw material for $Eu^{2+}$ dopant. The effects of molar ratio of component and experimental conditions on luminescence property of prepared phosphors have been investigated. The structure and luminescence properties of prepared $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphors were investigated by XRD and photoluminescence spectroscopy. The excitation spectra of $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphors indicated broad excitation wavelength range of 250 - 500 nm, namely from UV to blue region with distinct enhanced emission spectrum peaking at ${\approx}530nm$.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.5
• /
• pp.704-710
• /
• 2004

A poly(1-hexyl-3,4-dimethyl-2,5-pyrrolylene) (PHDP) was prepared and its luminescence in tetrahydrofuran (THF) was studied. When PHDP is excited by UV light, it produces very strong blue luminescence. The quantum yield of PHDP (Q = 36.9%) is much greater than that of the monomer, 1-hexyl-3,4-dimethylpyrrole (HDP) with Q = 0.61%. The principal luminescence of PHDP has a single decay component with ca. 1 ns, whereas the decay of HDP is complicated. The molecular structure and conformational behavior of HDP and the oligomers up to trimer have been also determined by ab initio Hartree-Fock (HF/6-31$G^{**}$), density functional theory (DFT-B3LYP/6-31$G^{**}$), and semiempirical (ZINDO) methods. According to the results of calculations, it is proposed that the enhanced quantum yield of the polymer PHDP results mostly from the ${\pi}$-conjugation between neighboring pyrrole rings.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.1
• /
• pp.9-15
• /
• 2002

In this thesis, blue emission organic light emitting devices were fabricated by using vacuum deposition method. Two types of device were employed to realize blue emission. Type I had an emitting layer containing TPB-doped $Alq_3$ and type II had an emitting layer containing DPA-doped $Alq_3$. The variable dopant concentration was 0.5 ~2 wt%. The electrical and optical characteristics of these devices have been investigated. The more dopant concentration increased, the nearer the blue coordinate. Type I than type II had a lower turn on voltage and driving voltage. The emission luminescence of type II was brighter than that of type I. When we applied 15V to type II with DPA(2wt%)-doped $Alq_3$, we have achived the emission luminescence of 1282cd/$m^2$, the emission wavelength of 476nm and the blue emission CIE coordination of (0.1273, 0.0672)

• Journal of the Korean Ceramic Society
• /
• v.43 no.5 s.288
• /
• pp.304-308
• /
• 2006

We have synthesized a $Eu^{2+}-activated\;Sr_3MgSi_2O_8$ blue phosphor and $(Sr,Ba)_2SiO_4$ yellow phosphor and prepared white LEDs by combining these phosphors with a InGaN UV LED chip. Three distinct emission bands from the InGaN-based LED and the two phosphors are clearly observed at 405 nm, 460 nm and at around 560 nm, respectively. The 405 nm emission band is due to a radiative recombination from a InGaN active layer. This blue emission was used as an optical transition of the $Sr_3MgSi_2O_8:Eu$ blue phosphor and $(Sr,Ba)_2SiO_4:Eu$ yellow phosphor. The 460 nm and 560 nm emission band is ascribed to a radiative recombination of $Eu^{2+}$ impurity ions in the $Sr_3MgSi_2O_8:Eu$ and $(Sr,Ba)_2SiO_4$ host matrix. As a consequence of a preparation of UV White LED lamp using the $Sr_3MgSi_2O_8:Eu$ blue phosphor and $(Sr,Ba)_2SiO_4:Eu$ yellow phosphor, the highest luminescence efficiency was obtained at the ration of epoxy/two phosphor (1/0.2361). At this time, the CIE chromaticity was CIE x = 0.3140, CIE y = 0.3201 and CCT (6500 K).

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.188-192
• /
• 2007

High brightness and long persistent luminescence phosphor $CaAl_2O_4:Eu^{2+}$ was prepared with varying $Eu^{2+}$ concentration by solid state reaction technique. Synthesized materials were investigated by powder X-ray diffractometer (XRD), SEM, TEM, photoluminescence excitation and emission spectra. Broad band UV excited luminescence of the $CaAl_2O_4:Eu^{2+}$ was observed in the blue region (${\lambda}_{max}\;=\;440\;nm$) due to transitions from the $4f^65d^1$ to the $4f^7$ configuration of the $Eu^{2+}$ ion. The decay time of the persistence indicated that the persistent luminescence phosphor has bright phosphorescence and maintains a long duration. These materials have great potential for outdoor night time displays.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.8
• /
• pp.2151-2157
• /
• 2010

Spectroscopic and quantum mechanical studies of the Et3PAuCl complex were performed to characterize the effect of aurophilicity on the optical properties. When excited with UV light at low temperature, the crystalline complex produced a deep luminescence in both the blue (high-energy) and red (low-energy) regions of the spectrum. The intensity of the low-energy luminescence was markedly reduced in the powdered state and quenched in the solution state. Time-dependent density functional theory (TD-DFT) calculations on electronic structures of both the ground and excited states of aggregates $[Et_3PAuCl]_n$ (n = 1 - 3) indicated that the low-energy luminescence was attributable to Au-centered transitions, which are significantly affected by aurophilic interactions. By contrast, the high-energy luminescence appeared to be independent of the state of the complex and was strongly associated with the charge transfer from Cl to Au.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.359-363
• /
• 2004

Photoluminescence excitation (PLE) spectroscopy studies were performed for anodically etched porous Zn, which exhibited a PL in the blue/violet spectral range peaking at 420 nm (2.95 eV), and oxidzed porous Zn at 380$^{\circ}C$ for 10 min and 12 h. A broad absorption band was observed at 4.07 eV (305 nm), 3.49 (355 nm) for anodically etched porous Zn. In contrast, both the oxidized porous Zn and sintered ZnO exhibited an almost identical one broad absorption band at 3.85 eV (322 nm), when PLE spectra were measured at 378 nm (3.28 eV). The oxidized porous Zn and sintered ZnO, which displayed both UV and green luminescence band, showed an additional absorption band at 389 nm (3.19 eV) and 467 nm (2.66 eV). In contrast, no significant absorption band was detected for a 10-min oxidized porous Zn, which only displayed one UV luminescence void of deep-level luminescence. These absorption bands determined by PLE studies enabled a clear understanding of an emission mechanism for the UV and green luminescence from ZnO.