• Journal of the Korean Geotechnical Society
• /
• v.30 no.1
• /
• pp.93-101
• /
• 2014

In this study, a blast furnace slag having latent hydraulic property with an alkaline activator for resource recycling was used to solidify sand without using cement. Existing chemical alkaline activators such as $Ca(OH)_2$ and NaOH were used for cementing soils. An alkaliphilic microorganism, which is active at higher than pH 10, is tested for a new alkaline activator. The alkaliphilic microorganism was added into sand with a blast furnace slag and a chemical alkaline activator. This is called the microorganism alkaline activator. Four different ratios of blast furnace slag (4, 8, 12, 16%) and two different chemical alkaline activators ($Ca(OH)_2$ and NaOH) were used for preparing cemented specimens with or without the alkaliphilic microorganism. The specimens were air-cured for 7 days and then tested for the experiment of unconfined compressive strength (UCS). Experimental results showed that as a blast furnace slag increased, the water content and dry density increased. The UCS of a specimen increased from 178 kPa to 2,435 kPa. The UCS of a specimen mixed with $Ca(OH)_2$ was 5-54% greater than that with NaOH. When the microorganism was added into the specimen, the UCS of a specimen with $Ca(OH)_2$ decreased by 11-60% but one with NaOH increased by 19-121%. The C-S-H hydrates were found in the cemented specimens, and their amounts increased as the amount of blast furnace slag increased through SEM analysis.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.4
• /
• pp.45-56
• /
• 2013

In this study, a blast furnace slag with latent hydraulic property is used to cement granular soils without using Portland cement. When the blast furnace slag reacts with an alkaline activator, it can cement soils. The effect of amounts of blast furnace slag and types of alkaline activator on soil strength was investigated for resource recycling. Four different amounts of slag and six different activators (two naturals and four chemicals) were used for preparing specimens. The specimens were air-cured for 3 or 7 days and then tested for unconfined compressive strength (UCS). The UCS of cemented sand with slag increased, in the order of specimens mixed with potassium carbonate, calcium hydroxide, sodium hydroxide and potassium hydroxide. Chemical alkaline activator was better than natural alkaline activator. The maximum UCS of 3-days cured specimens was 3 MPa for 16% of slag with potassium hydroxide, which corresponded to 37% of one with 16% of high-early strength portland cement. As the amount of slag increased, the UCS and dry density of a specimen increased for all alkaline activator cases. As the curing time increased from 3 days to 7 days, the UCS increased up to 97%. C-S-H hydrates were found in the cemented specimens from XRD analyses. Cement hydrates were more generated with increasing amount of slag and they surrounded sand particles, which resulted in higher density.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.215-216
• /
• 2011

This study investigates the effect of partial replacement with cement on the properties of blast furnace slag-based mortar. Recycled fine aggregate with various contents was used to activate the hydration of blast furnace slag in the mortar and compared its effect on strength development. Results showed that increasing cement and recycled fine aggregate increased the strength of mortar specimens. However, this study found that the mortar made with partial replacement of river sand with recycled fine aggregate of 20% developed a similar strength to the strength that cement with 10% can achieved.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.6
• /
• pp.11-17
• /
• 2013

This study was performed to evaluate the chlorine ion penetration resistance, chemical resistance and freezing and thawing resistance used ordinary portland cement, crushed coarse aggregate, crushed sand, river sand, fly ash, limestone powder, blast furance slag powder and superplasticizer to find optimum mix design of low carbon green concrete for structures. The performance of low carbon green concrete used fly ash, limestone powder and blast furnace slag powder were remarkably improved. This fact is expected to have economical effects in the manufacture of low carbon green concrete for offshore structures. Accordingly, the fly ash, limestone powder and blast furnace slag powder can be used for offshore structure materials.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.17-18
• /
• 2022

Carbon dioxide emissions in the construction sector account for 38% of all industries, and environmental destruction is occurring due to indiscriminate use of natural resources. The purpose of this study is to develop by-product aggregate Non-Sintered Cement(NSC) that can replace sand used as natural aggregate and Portland cement. Therefore, Ground Granulated Blast Furnace Slag, Type C Fly Ash and Type F Fly Ash are used to replace cement, and water granulated ferro-nickel slag(FNS) is used to replace aggregate. The flow, compressive strength and flexural strength of the formulation using sand as an aggregate and the formulation replacing 100% FNS were compared. As a result of the experiment, the formulation using FNS had higher overall strength than the formulation using sand, and as the substitution rate of Type C fly ash increased, the strength was the best. Formulation using FNS is more fluid than using sand. Through this study, we show the possibility of 100% substitution of FNS and its applicability to secondary concrete products of by-product aggregate NSC.

• Advances in concrete construction
• /
• v.5 no.5
• /
• pp.437-450
• /
• 2017

The present work investigates about the development of a novel construction material by utilizing Granulated Blast Furnace Slag (GBS), an industrial waste product, as substitution of natural fine aggregates. For this, experimental work has been carried out to determine the influence of GBS on the properties of concrete such as compressive strength (CS), modulus of elasticity, ultrasonic pulse velocity (UPV), chloride penetration, water absorption (WA) volume of voids (VV) and density. Concrete mixes of water/cement (w/c) ratios 0.45 and 0.5, and incorporating 20%, 40% and 60% of GBS as partial replacement of natural fine aggregate (sand) are designed for this study. The results of the experimental investigation depict that CS of concrete mixes increases with the increasing percentages of GBS. Moreover, the decrease in chloride penetration, WA and VV, and improvement in the modulus of elasticity, UPV, density of concrete is reported with the increasing percentage of GBS in concrete.

• Advances in concrete construction
• /
• v.6 no.6
• /
• pp.611-629
• /
• 2018

The objective of present study is to investigate the effect of granulated blast furnace slag (GBS) as partial substitution of natural sand on behaviour of cement mortar. For this, the methods of factorial design with water cement (w/c) ratio and incorporation percentages of GBS as replacement of natural fine aggregate i.e., GBS(%) as factors are followed. The levels of factor w/c ratio are fixed at 0.4, 0.45, and 0.5 and the levels of factor GBS(%) are kept fixed as 0%, 20%, 40%, 60%, 80% and 100%. The compressive strength (CS) of mortar after 3, 7, 14, 28, 56 and 90 days, and water absorption (WA) are chosen as responses of the study. Analysis of variance (ANOVA) of experimental results has been carried out and those are illustrated by ANOVA tables, main effect and interaction plots. The results of study depict that the selected factors have substantial influence on the strength and WA of mortar. However, the interaction of factors has no substantial impact on CS and WA of mixes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.186-187
• /
• 2022

The purpose of this study was to give fluidizing properties to non-sirtered cement made using by-products that can replace Portland cement by using a fluidizing agent. Blast furnace slag, C-type fly ash, and F-type fly ash were used for non-sirtered cement, and sand was used for aggregate. The amount of fluidizing agent used was fixed at 1%, and the water-cement ratio (W/C) was different by setting the binder blending ratio of the non-sintered cement differently, and the fluidity test and flow were compared. As a result of the experiment, when the flow standard was 170mm when the fluidizing agent was used, the fluidizing properties were shown at an average water-cement ratio (W/C) of 36%. Through this study, it was confirmed that the fluidizing properties appeared when the fluidizing agent was used in non-sintered cement.

• Journal of the Korean Ceramic Society
• /
• v.18 no.1
• /
• pp.3-12
• /
• 1981

A glass-ceramics based on blast-furnace slag, with some additives to the theoretical composition in order to control properties of mother glass and the heat treatment conditions, has been investigated. The raw materials in this study were blast-furnace slag, serpentine, feldspar and quartz as mother glass ingredients. Titanium dioxide and chromite were used as the nucleating agents. Batch compositions of the prepared glasses and ceraming conditions were found by trial and error method. The optimum conditions were confirmed by analyzing several measured physical properties such as density change during heat treatment, microhardness of slag-ceramics prepared, viscosity change of glass at heat treatment temperatures, nucleation density change, dilatometric properties, differential thermal analysis, identification of the grown crystal and crystal sizes. The batch composition feasible to prepare slag-ceramics was 40% of blast-furnace slag, 25% of serpentine, 18% of feldspar and 17% of silica sand. Three percent titanium dioxide and 1% chromite of the mother glass were added as nucleating agents. The ceraming conditions under which the slag-ceramics having considerably good properties can be developed found as: "The glass was heated at 75$0^{\circ}C$ for 2 hours for nucleation, and the temperature was raised up to 1, 00$0^{\circ}C$ with a rate of 0.75$^{\circ}C$/min for crystal growth.owth.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.3
• /
• pp.9-12
• /
• 2013

The pavement is generally used on the highways, local loads, roads for bicycle riding and neighborhood living facility such as parking lot, plaza, park and sports facilities. However, the pavement material that is usually used on the most of roads is impermeable asphalt-concrete and cement-concrete. If the pavement material is impermeable, many problems can be happened on the drainage facilities in the rainy season. Additionally, a lot of rainwater on the pavement surface cannot permeate to the underground and flows to the sewage ditch, stream and river, etc. If a lot of rainwater flows at once, the floods can be out along the streams and rivers. So, underground water can be exhausted. Micro organisms cannot live in the underground. Recently, many studies has been conducted to exploit the permeable concrete that has high performance permeability. However, it is required to develop the permeable concrete which has high strength and durability. In this study, permeable and strength tests were performed to investigate the permeable characteristics of porous concrete according to fine aggregate content and substitution ratio of blast furnace slag. In this test, crushed stones with 10~20 mm and sand with 5~10 mm were used as a coarse aggregate and a fine aggregate respectively. The substitution ratio of blast furnace slag to cement weight is 0 %, 15 %, and 30 %. The ratio of fine aggregate to total aggregate is 0 %, 18 %, and 35 %. As a result, permeability coefficient was decreased according to fine aggregate ratio of total aggregate. Compressive strength was also decreased according to substitution ratio of blast furnace slag.