• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.34-39
• /
• 1999

IN this study when drawing a square cup blank holder pressure necessary for flange wrinkling prevention was experimentally studied. The materials used in the experiment were SPCC and SUS304 and drawing ratio was 1.62∼2.0 Two case for lubrication condition were experimented. One was without lubricant and the other was with lubrication of high viscosity.

• 소성∙가공
• /
• 제9권4호
• /
• pp.356-361
• /
• 2000

In this study, when a square cup is under drawing, blank holder pressure necessary for flange wrinkling prevention was experimentally studied. The materials used in the experiment were SPCC steel and SUS304 and the drawing ratio was 1.62∼2.0. Two cases for lubricantion condition were investigated. One was without lubricant and the other was with lubricant of high viscosity.

• Design & Manufacturing
• /
• 제17권4호
• /
• pp.8-13
• /
• 2023

In this study, it was studied whether a new measurement factor "frictional vibration" that occurs due to the material flow of the die and sheet metal in the flange area during deep drawing process, could be measured using an vibration sensor. The blank holder force acting on the flange area during drawing processing acts as a friction force in the opposite direction into which the sheet material flows and causes friction vibration. As the blank holder force increases, the friction force increases, and as the blank holder force decreases, the friction force also decreases. Because of this, friction vibration also increases and decreases in proportion to the size of the blank holder force. According to this theory, whether frictional vibration occurs was measured using a flange simulator and a vibration sensor. The initial pressure was created using a torque wrench, and it was confirmed that the amplitude increased by about 4 times when torque 6 Nm was increased. When the forming velocity was rapidly changed to 300 mm/min, the amplitude increased approximately 4 times. It was confirmed that the amplitude of frictional vibration according to the measurement location was greater the further away from the specimen. It was verified that a new measurement factor "friction vibration" in the flange area can be measured and used for online monitoring.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.25-30
• /
• 1997

In this study, the forming behavior of Tailor welded HS and IF steel s-rail stamping is analyzed by experiments and simulations. According to the results, uniform strain distribution in the formed part is most important to prevent springback and wrinkle formation. For that purpose, it is most effective to distribute uniformly the contact pressure of blank and bland holder.

• Design & Manufacturing
• /
• 제14권1호
• /
• pp.22-29
• /
• 2020

The analysis was carried out using the press molding analysis program by applying six parameters such as material type change, material thickness, friction coefficient, r_p, r_d and blank holder pressure. As a result of CAE analysis of the soft material DC04 and the relatively hard material HX300LAD, the thickness of the punch R part of the soft material was significantly reduced. The flange portion is greatly increased in thickness in the hard material by the compression action. As a result of considering the deformation amount of 0.6mm, 1.0mm, 1.5mm according to the material thickness, the influence of the thickness is considered to be very small. In case of the material thickness of 0.6mm, the rate of change increases due to the deep drawing depth relative to the material thickness. The sizes of the punches R and die R have the greatest influence on the change in thickness of the material in drawing molding, the smaller the punch R, the thinner the edges of the product, The larger the R of the die, the greater the material thickness of the flange portion. As the coefficient of friction and the blank holder pressure increase, the frictional force of the flange portion increases, which increases the radial force in the drawing process and increases the thickness change of the flange portion.

• 소성∙가공
• /
• 제26권2호
• /
• pp.87-94
• /
• 2017

Center pillar, which is installed in the center of flank of car body, supports roof and door and ensures the safety of driver by reducing the damage of car body caused by impact. Recently, high-strength steel is widely used to manufacture the center pillar due to high stiffness and fuel efficiency. In this study, material properties of the high-strength steel, whose tensile strength is more than 780MPa, were obtained to produce the center pillar. Stamping was performed by considering the design parameters (blank holder force, press stroke, blank size and pad pressure) used in the actual filed. The drawbeads were included in the stamping process to reduce the amounts of wrinkling and spring back. Using the commercial software, Autoform R5.2 and Minitab, effects of design parameters of the stamping process upon spring back were analyzed and applied to the design process. The restriking process meets the target of under 0.5mm in the amount of spring back.

• Design & Manufacturing
• /
• 제16권2호
• /
• pp.39-45
• /
• 2022

Sheet Metal Forming by Press Forming Process takes a lot of time and cost from mold design to manufacturing. Therefore, all of die-makers are continuously conducting research to reduce the number of mold processes or the size of blanks to reduce costs. In the case of Forming complex shapes such as automobile component, wrinkles and cracks occur, so draw beads are used. Draw beads play an important role in suppressing the inflow of materials and minimizing the size of blanks. Factors that affect material flow include draw bead, blank holding pressure, lubricant, and surface roughness of punch and die. Most of the factors affect friction. In this study, after classifying circular beads and rectangular beads in cylindrical drawing molds using the AutoForm analysis program, the factors affecting the material inflow were considered.

• 한국정밀공학회지
• /
• 제22권12호
• /
• pp.93-99
• /
• 2005

In this work, computer-aided process design is carried out to develop an optimal preform of a pressure vessel. Knowledge-based rules are employed to design the preform, and they are formulated using the handbooks of plasticity theories. In the FE-analysis, a commercial finite element code, ABAQUS was employed. Axisymmetric deep drawing of a hemisphere-bottomed cup has been analyzed fur various combinations of die design parameters. The length of the land of die, the clearance between punch and die and the clearance between the blank holder and die are optimized to minimize the forming load. The results of the simulations are verified with the experiments which are scaled down to one tenth of the actual size.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.616-620
• /
• 2001

The wrinkling in the flange and wall of a part is a predominent failure mode in stamping of sheet metal parts. In many cases this wrinkling may be eliminated by appropriate control of the blank holding force(BHF), but BHF affects the draw depth. Although the wrinkles of flange have been made in the incipient stage of drawing, if the height of wrinkles is maintained under a prescribed limit by decrease or extinction of wrinkles in the course of drawing, small BHP can be allowed so that the depth of drawing could be increased. Authors research the variation of the wrinkles in flange in the course of square cup drawing by using aluminium A1015 and aluminium alloy A5052.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.845-848
• /
• 2002

The wrinkling in the flange and wall of a part is a predominent failure mode in stamping of sheet metal parts. In many cases this wrinkling may be eliminated by appropriate control of the blank holding forco(BHF), but BHF affects the draw depth. Gotoh had studied the wrinkles under 0.02mm in height. In general, the height of wrinkles could be limited under 0.2mm practically. Therefore small BHP can be allowed so that the depth of drawing could be increased. Authors research the variation of the wrinkles in flange in the course of cup drawing by using aluminium alloy Al050 and A5052.