• Current Optics and Photonics
• /
• 제6권1호
• /
• pp.32-38
• /
• 2022

Erbium-doped fiber amplifiers (EDFAs) have saturated the technological market but are still widely used in high-speed and long-distance communication systems. To overcome EDFA saturation and limitations, its erbium-doped fiber is co-doped with other materials such as zirconia and bismuth. This article demonstrates and compares the performance using three different fibers as the gain medium for zirconia-erbium-doped fibers (Zr-EDF), bismuth-erbium-doped fibers (Bi-EDF), and commercial silica-erbium-doped fibers (Si- EDF). The optical amplifier was configured with a double-pass amplification system, with a broadband mirror at the end of its configuration to allow double-pass operation in the system. The important parameters in amplifiers such as optical properties, optical amplification and noise values were also examined and discussed. All three fibers were 0.5 m long and entered with different input signals: 30 dBm for low input and 10 dBm for high input. Zr-EDF turned out to be the most relevant optical amplifier as it had the highest optical gain, longest transmission distance, highest average flatness gain with minimal jitter, and relevant noise figures suitable for the latest communication technology.

• Journal of the Optical Society of Korea
• /
• 제14권4호
• /
• pp.298-304
• /
• 2010

The pair-induced quenching (PIQ) effect in a highly doped bismuth oxide-based erbium-doped fiber amplifier (EDFA) was theoretically and experimentally investigated. In the theoretical investigation, the bismuth oxide-based EDFA was modeled as a 6-level amplifier system that incorporated clustering-induced concentration quenching, cooperative up-conversion, pump excited state absorption (ESA), and signal ESA. The relative number of paired ions in a highly doped bismuth oxide EDF was estimated to be ~6.02%, determined by a comparison between the theoretical and the experimentally measured gain values. The impacts of the PIQ on the gain and the noise figure were also investigated.

• Journal of Magnetics
• /
• 제20권2호
• /
• pp.103-109
• /
• 2015

In this study, the authors attempted to produce a medical radiation shielding fiber that can be produced at a nanosize scale and that is, unlike lead, harmless to the human body. The performance of the proposed medical radiation shielding fiber was then evaluated. First, diamagnetic bismuth oxide, an element which, among elements that have a high atomic number and density, is harmless to the human body, was selected as the shielding material. Next, 10-100 nm sized nanoparticles in powder form were prepared by ball milling the bismuth oxide ($Bi_2O_3$), the average particle size of which is $1-500{\mu}m$, for approximately 10 minutes. The manufactured bismuth oxide was formed into a colloidal solution, and the radiation shielding fabric was fabricated by curing after coating the solution on one side or both sides of the fabric. The thicknesses of the shielding sheets prepared with bismuth oxide were 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, and 1.0 mm. An experimental method was used to measure the absorbed dose and irradiation dose by using the lead equivalent test method of X-ray protection goods presented by Korean Industrial Standards; the resultant shielding rate was then calculated. From the results of this study, the X-ray shielding effect of the shielding sheet with 0.1 mm thickness was about 55.37% against 50 keV X-ray, and the X-ray shielding effect in the case of 1.0 mm thickness showed shielding characteristics of about 99.36% against 50 keV X-ray. In conclusion, it is considered that nanosized-bismuth radiation shielding fiber developed in this research will contribute to reducing the effects of primary X-ray and secondary X-ray such as when using a scattering beam at a low level exposure.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 창립 20주년기념 특별학술발표회
• /
• pp.32-33
• /
• 2009

• 한국광학회지
• /
• 제21권4호
• /
• pp.139-145
• /
• 2010

본 논문에서는 고농도로 도핑된 Bismuth 기반 어븀첨가 광섬유 증폭기의 이득 및 노이즈 특성을 정확히 예측하기 위하여 필요한 이론적 모델링 기법에 대한 연구를 수행 하였다. 고농도의 Erbium 이온이 첨가되었을 때 발생하는 Clustering 현상에 기인한 Inhomogeneous Broadening현상, Cooperative Upconversion 현상, Pump Excited State Absorption과 Signal Excited State Absorption 현상 등 모든 현상을 고려하여 6 레벨 증폭기 System Model을 제시하고 이를 전산모사하여 실험치와 비교함으로써 제시된 모델의 유효성을 검증하였다.

• Journal of the Optical Society of Korea
• /
• 제11권2호
• /
• pp.63-66
• /
• 2007

A 9.6 dB gain is observed at 1310 nm in a 5.0 cm bismuth-doped silica fiber. A launched pump power of 100 mW was obtained using an 810-nm laser diode. We demonstrated the simultaneous optical amplification at two wavelengths near second telecommunication windows, which is the range of zero-dispersion for silica fibers.

• 한국환경과학회지
• /
• 제16권10호
• /
• pp.1111-1118
• /
• 2007

A bismuth-coated carbon fiber microelectrode was prepared using cyclic voltammetry (CV). An analytical application was performed for the copper analysis with Square Wave Stripping Voltammetry (SWSV). Gallic acid n-propyl ester (PG) was used for the complex formation with a copper ion, and electrochemical measurements were performed with a pre-amplifier of a low-current module for nano am per detection. The effects of various parameters on the response were optimized. Analytical working ranges of $0.03-25.9\;{\mu}gl^{-1}$ and $0-25\'mgl^{-1}$ Cu(II) were obtained. The relative standard deviation at $13\;mgl^{-1}$ Cu was 0.9% (n = 12) in optimum conditions. The detection limit was found to have been $0.019\;{\mu}gl^{-1}$, with a 30-sec accumulation time. The developed methods were applied to a copper assay in water samples.

• 한국통신학회논문지
• /
• 제21권6호
• /
• pp.1596-1603
• /
• 1996

A single body type of fiber-optic current and voltae sensor using a rare earth doped YIG and a bismuth silicon oxide single crystsl is proposed, which is used for simultaneous measurement of the AC electric current and AC electric voltage over the trasmission lines. Experimental results showed that the fiber-optic current sensor has the maximum 7.5% error within the current range of 0A to 400A, and the fiber-optic voltage sensor has the maximum 0.87% error within the current range of 0V to 400V. The output waveforms of proposed fiber-optic sensor system has a good agreement with output waveforms of conductor current and voltage. Experimental results proved that the output of fiber-optic current sensor is not affected by the electric voltage applied to the fiber-optic voltage sensor, and also, that the output of fiber-optic voltage sensor is not affected by the electric current applied to the fiber-optic current sensor.

• 한국광학회지
• /
• 제18권3호
• /
• pp.221-225
• /
• 2007

근적외선에서 발광하는 새로운 증폭 매질인 Bi 첨가 알루미노실리케이트 유리의 용융 온도를 낮추면서도 증폭 특성이 향상될 수 있도록 금속 산화물을 첨가한 샘플을 제작하여 분광학적 특성을 분석하였다. $Li_{2}O$의 조성비가 증가하면 형광스펙트럼의 반폭치는 증가하지만 형광 강도가 저하되고, $GeO_{2}$의 영향으로는 반폭치와 형광 강도가 동시에 증가하였다. $GeO_{2}$를 첨가한 시료에서 광 증폭 특성을 측정한 결과, 이전의 벌크 샘플에서 얻었던 것보다 우수한 증폭 특성을 가지고 있음을 확인하였다.

• Advances in nano research
• /
• 제1권4호
• /
• pp.183-192
• /
• 2013

One-dimensional multiferroic nanostructured composites have drawn increasing interest as they show tremendous potential for multifunctional devices and applications. Herein, we report the synthesis, structural and dielectric characterization of barium titanate ($BaTiO_3$)-bismuth ferrite ($BiFeO_3$) composite fibers that were obtained using a novel sol-gel based electrospinning technique. The microstructure of the fibers was investigated using scanning electron microscopy and transmission electron microscopy. The fibers had an average diameter of 120 nm and were composed of nanoparticles. X-ray diffraction (XRD) study of the composite fibers demonstrated that the fibers are composed of perovskite cubic $BaTiO_3$-$BiFeO_3$ crystallites. The magnetic hysteresis loops of the resultant fibers demonstrated that the fibers were ferromagnetic with magnetic coercivity of 1500 Oe and saturation magnetization of 1.55 emu/g at room temperature (300 K). Additionally, the dielectric response of the composite fibers was characterized as a function of frequency. Their dielectric permittivity was found to be 140 and their dielectric loss was low in the frequency range from 1000 Hz to $10^7$ Hz.