• 한국안전학회지
• /
• 제32권3호
• /
• pp.1-7
• /
• 2017

Particle reinforced composites are materials that have enhanced physical properties by adding particle reinforcements to polymer materials and have been applied to a wide range of fields such as the aerospace, bio-technology and automative industry. In this study, particle reinforced composites were prepared by mixing $SiC/Al_2O_3$ to the vinyl ester as the thermoset resin. The purpose of this study is to evaluate mechanical properties and fracture behavior by the tensile test and single edge notch specimen according to the addition ratio of reinforcement. Addition of 1 and 2 wt% of the particle reinforcement to the vinyl-ester resin was effective for the strength improvement. However, when it was more than 3 wt%, its strength was decreased. Also the highest elastic modulus obtained as 3.19 GPa was found at the 2 wt% addition of reinforcement. Futhermore the fracture toughness was evaluated by the energy release rate and the maximum critical energy release rate was obtained when 1 wt% reinforcement. The results show that the limit of adding of $SiC/Al_2O_3$ for improvement of the mechanical and fracture performance is 2 wt% reinforcement particles.

• Journal of the Korean Wood Science and Technology
• /
• 제35권5호
• /
• pp.58-66
• /
• 2007

The objective of this research was to develop environment-friendly adhesives for face fancy veneer bonding of engineered flooring. Urea-formaldehyde (UF)-tannin and melamine-formaldehyde (MF)/PVAc hybrid resin were used to replace UF resin in the formaldehyde-based resin system in order to reduce formaldehyde and volatile organic compound (VOC) emissions from the adhesives used between plywoods and fancy veneers. Wattle tannin powder (5 wt%) was added to UF resin and PVAc (30 wt%) to MF resin. These adhesive systems showed better bonding than commercial UF resin with a similar level of wood penetration. The initial adhesion strength was sufficient to be maintained within the optimum initial tack range. The standard formaldehyde emission test (desiccator method) and VOC analyzer were used to determine the formaldehyde and VOC emissions from engineered flooring bonded with commercial UF resin, UF-tannin and MF/PVAc hybrid resin. By desiccator method, the formaldehyde emission level of UF resin showed the highest but was reduced by replacing with UF-tannin and MF/PVAc hybrid resin. MF/PVAc hybrid satisfied the $E_1$ grade (below $1.5mg/{\ell}$). VOC emission results by VOC analyzer were similar with the formaldehyde emission results. TVOC emission was in the following order: UF > UF-tannin > MF/PVAc hybrid resin.

• 한국식품저장유통학회지
• /
• 제13권3호
• /
• pp.363-368
• /
• 2006

초임계추출법을 이용하여 향유로부터 정유물질을 추출하여 향기성분과 항산화물질을 최대로 추출할 수 있는 최적조건을 반응표면 분석법으로 얻고자 하였다. 추출물의 품질특성으로는 yield, total phenolics, electron donating ability 등을 분석하였으며 주요 향기성분으로는 estrgole과 L-carvone을 선정하였다. 반응변수들은 추출시간보다는 온도의 변화에 따라 비례적으로 증가하는 경향을 보였으며, 측정된 변수에 대하여 수립된 회귀식은 높은 결정계수값을 가지는 것으로 나타났다. 추출시간보다는 압력이 더 큰 변수로 작용하여 1% 이내의 유의성이 있었으며 이차 회귀식에 대한 적합성 결여분석 결과 수립된 반응표면 모형이 통계적으로 유의하였다. 능선분석을 통하여 각 변수에 대한 최적점과 추출조건을을 예측하였으며, 최적 추출조건은 실험구간내에서 추출물의 특성값을 최대로 할수 있는 조건을 제한조건하였을 때 최적조건은 238 bar, 42분이었다.

• 한국식품저장유통학회지
• /
• 제17권2호
• /
• pp.261-266
• /
• 2010

식물체의 플라보노이드 성분 함량 분석에 필요한 적정 가수분해 조건을 구명하기 위하여 은행잎을 이용하여 중심합성법으로 설계한 산 가수분해 시간과 HCl 농도에 따라 myricetin, quercetin, kaempferol 함량을 HPLC로 분석하고, SAS의 반응표면분석법으로 산 가수분해 조건의 최적화를 시도하였다. HCl 0.5~2.5 M, 0.5~2.5시간 범위 내에서 10개의 구간을 잡아서 최적화한 결과 1.5~1.9 M의 HCl 농도와 1.4~2.0시간의 가수분해 조건에서 myricetin, quercetin, kaempferol 성분이 가장 높았다. Superimposing하여 구한 식물체의 플라보노이드의 적정 가수분해 조건은 HCl 1.5 M, 1.5시간이었으며, 이 조건에서 구한 플라보노이드 함량의 예측치와 측정치는 95% 이상 일치하였다. 본 연구에서 구한 적정 가수분해 조건을 이용하여 녹차잎, 무화과잎, 상동나무잎의 플라보노이드 함량을 분석하여 보았다.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제30권5호
• /
• pp.480-488
• /
• 2008

Orthodontists often treat cases which are difficult to treat with conventional orthodontics. In such cases, it could be treated with surgical procedures with the help of an oral surgeon. Especially, transverse deficiency of the mandible can be corrected by widening the transverse width of mandibular symphysis, using distraction osteogenesis. Transverse widening of mandibular sympysis is known as a safe treatment but still complications could occur during the treatment. We are reporting some complications of cases that mandibular symphysis transverse widening were applied. Some cases showed complications because of the inappropriate osteotomy line. Since straight vertical osteotomy line was inclined to the left, only the left bony segment was likely to expand. According to bio-mechanical considerations, it will be better to perform a step osteotomy, cutting the eccentric area of the alveolar crest and the centric area of the basal symphyseal area. Complications could also occur by the failure of the distraction device. The tooth borne distraction device was attached on the lingual side of the tooth with composite resin. During the distraction period, it was impossible to obtain appropriate distraction speed and rhythm because of frequent fall off of the distraction device. Therefore, distraction device should be attached firmly with orthodontic band or bone screw, etc. Tooth mobility increasement could also occur as a complication. 'Walking teeth phenomenon' was observed during the distraction period, showing severe teeth mobility and pain during mastication. These symptoms fade out during the consolidation period. Since the patient could feel insecure and uncomfortable, it should be notified to the patient before the procedure. Finally, alveolar crestal bone loss could occur. Alveolar crestal bone loss occurred because of lack of distraction device firmness and teeth trauma caused by lower lip biting habit. Therefore, adequate firmness of the distraction device and habit control will be needed.

• 대한한의학회지
• /
• 제30권5호
• /
• pp.26-41
• /
• 2009

Objectives: The experiment was to estimate the value of Saengmaegsan as a therapeutic anti-aging agent with an analysis of ingredients and their bio-activating effects by enzymologic methods. Methods: We analyzed anti-aging effects of the ingredients of Saengmaegsan being Liriope Platyphylla, Schizandrae Chinensis, and Schizandrae Chinensis. Results: In Liriope Platyphylla and Schizandrae Chinensis, reducing sugar concentration was shown at the highest level. Of mineral contents, K+ and Na+ were the highest in Saengmaegsan and each ingredient also, and then Ca++ and Al. The amount of polyphenol showed was in order Schizandrae Chinensis > Saengmaegsan > Panax Ginseng > Liriope Platyphylla. The electron donating ability of Schizandrae Chinensis doubled that of Saengmaegsan and Panax Ginseng, at the same time that one per 1 ml in Saengmaegsan was significantly found the greatest level as compared to each single ingredient. SOD-like activity was high in Saengmaegsan and Schizandrae Chinensis. SOD-like activity of Saengmaegsan was higher than in single components. Nitric oxide inhibition in pH 1.2 was high in Saengmaegsan and Schizandrae Chinensis, and for per 1 ml it showed the same pattern as above. In pH 3.0 the result was not different from in pH 1.2. Xanthine oxidase inhibition was high in Schizandrae Chinensis and for per 1 ml showed the greatest activity in Liriope Platyphylla. Tyrosinase inhibition in Omija was the most noticeable, and for per 1 ml was Liriope Platyphylla more than any others. Conclusions: With this analysis of ingredients, it is proven that Saengmaegsan and each component fosters antioxidation. On the whole, the composite prescription Saengmaegsan was superior to each individual component.

• 한국물환경학회지
• /
• 제31권6호
• /
• pp.693-699
• /
• 2015

It has been known that torrential rainfall events have been occurring worldwide due to climate change. The accelerated soil erosion has caused negative impacts on water quality and ecosystem of receiving waterbodies. Since soil security issues have been arising in various areas of the world, intensive interests have been given to topsoil management in Korea. Thus in this study, Web GIS-based computing system of physical, chemical, and biological topsoil quality indices were developed. In this study, five soil quality maps at national scale and top soil erosion potential were prepared for evaluation of soil quality based on soil erosion potential. For this system, the open source Web GIS engine, OpenGeo, was used as core engine of the system. With this system, decision makers or related personnel in areas of soil erosion Best Management Practices (BMPs) would be able to find the most appropriate soil erosion BMPs based on soil erosion potential and soil quality at the area of interest. The Web GIS system would be efficiently used in decision making processes because of ease-of-use interface and scientific data used in this system. This Web GIS system would be efficiently used because this system could provide scientific knowledge to decision makers or stakeholders. Currently various BMP database are being built to be used as a decision support system in topsoil management and topsoil quality areas.

• Food Science and Biotechnology
• /
• 제16권4호
• /
• pp.557-564
• /
• 2007

We prepared caviar analogs encapsulated by calcium-alginate gel membranes as a means to replace higher priced natural caviars. Processing the caviar analogs (beluga type) was optimized by response surface methodology with central composite design. Concentrations of sodium alginate ($X_1$) and $CaCl_2\;(X_2)$ were chosen as the independent variables. In order to compare characteristics of the caviar analogs with the natural caviar, sphericity ($Y_1$), diameter ($Y_2$), membrane thickness ($Y_3$), rupture strength ($Y_4$), rupturing deformation ($Y_5$), and sensory score ($Y_6$) were used as the dependent variables. The sphericity of the caviar analogs showed a similar value to that of natural caviar (over 94%) in the range of independent variables. Generally, the $CaCl_2$ concentration ($X_2$) affected all dependent variables to a greater extent than the sodium alginate concentration ($X_l$), For the multiple response optimization of the 5 dependent variables ($Y_1,\;Y_2,\;Y_4,\;Y_5$, and $Y_6$), the desirability function was defined as the following conditions: target values ($Y_1\;=\;100%,\;Y_2\;=\;3.0\;mm,\;Y_4\;=\;1,470\;g,\;Y_5\;=\;1.1\;mm,\;and\;Y_6\;=\;10\;points$). Membrane thickness ($Y_3$) was eliminated from the dependent variables for multiple response optimization because it could not be measured with an image analyzer. The values of the independent variables as evaluated by multiple response optimization were $X_1\;=\;-0.093$ (78%) and $X_2\;=\;-0.322$ (1.07%), respectively.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.4-4
• /
• 2012

Proteins enable biology to be viable through molecular interactions (such as in antigen-antibody, ligand-receptor, and drug-target) with

• 멤브레인
• /
• 제30권4호
• /
• pp.213-227
• /
• 2020

재생 불가능한 에너지 자원이 수년에 걸쳐 고갈됨에 따라, 재생 에너지 생산을 위한 보다 효과적인 방법에 대한 연구가 증가되었다. 연로전지 개발의 한 분야인 미생물 연료전지(MFC)는 이중 성능의 잠재력 덕분에 발전하였다. MFC는 박테리아와 같은 전극 감소 생물에서 전력을 모아서 전기 에너지를 생산한다. MFC는 폐수를 연료로 사용하여 에너지를 생산하고 폐수를 정화한다. 양성자 교환막(PEM)은 양극과 음극 챔버의 분리막으로, 양성자만 효과적으로 통과할 수 있게 하는 중요한 역할을 한다. Nafion은 MFC에 상업적으로 사용되는 PEM이지만 비용, 생산 시간, 양성자 전도성 차원에서 보완할 점들이 많다. 본 리뷰 논문에는 Nafion을 대체할 수 있는 새로 개발된 PEM 몇 가지를 논의하였다. 또한, PEM, 혼합 PEM 및 복합 PEM에 기반한 MFC를 요약하고자 한다.