• The Journal of the Korea Contents Association
• /
• v.9 no.2
• /
• pp.88-96
• /
• 2009

In this paper we suggest the EEF technique to improve the performance of U-Health System. The idea of the EEF technique is that a sensor node sends only the abnormal data of patients to the base node. This technique reduces the amount of data transfer between a base node and sensor nodes, and so the power consumption of sensor nodes will be saved. And also the processing cost of base node will be reduced. In the suggested U-Health System based on EEF technique, electrocardiogram sensors and GPS sensors are used to send the electrocardiogram and position information of patients to a server. The server analyzes the health state of patients from base nodes and sends the information about the patients in the emergent state to the nearest hospital. Through the simulation, we have confirmed the suitability of EEF technique for U-Health System.

• Korean Journal of Agricultural Science
• /
• v.42 no.1
• /
• pp.53-61
• /
• 2015

Development of highly efficient and energy-saving tractors has been one of the issues in agricultural machinery. For design of such tractors, measurement and analysis of load on major power transmission parts of the tractors are the most important pre-requisite tasks. Objective of this study was to perform pre-processing procedures before effective analysis of load data of agricultural tractors (30, 75, and 82 kW) during major field operations such as plow tillage, rotary tillage, baling, bale wrapping, and to select the suitable pre-processing method for the analysis. A load measurement systems, equipped in the tractors, were consisted of strain-gauge, encoder, hydraulic pressure, and radar speed sensors to measure torque and rotational speed levels of transmission input shaft, PTO shaft, and driving axle shafts, pressure of the hydraulic inlet line, and travel speed, respectively. The entire sensor data were collected at a 200-Hz rate. Plow tillage, rotary tillage, baling, wrapping, and loader operations were selected as major field operations of agricultural tractors. Same or different farm works and driving levels were set differently for each of the load measuring experiment. Before load data analysis, pre-processing procedures such as outlier removal, low-pass filtering, and data division were performed. Data beyond the scope of the measuring range of the sensors and the operating range of the power transmission parts were removed. Considering engine and PTO rotational speeds, frequency components greater than 90, 60, and 60 Hz cut off frequencies were low-pass filtered for plow tillage, rotary tillage, and baler operations, respectively. Measured load data were divided into five parts: driving, working, implement up, implement down, and turning. Results of the study would provide useful information for load characteristics of tractors on major field operations.

• Korean Journal of Agricultural Science
• /
• v.46 no.4
• /
• pp.723-735
• /
• 2019

The power-train is the most important component of an agricultural tractor. In this study, the strength of the driving gear transmission of an 82 kW-class tractor was analyzed using equivalent torque during plow tillage. The load measurement system consisted of an engine revolution speed sensor, torque-meters, revolution speed sensors for four axles, and pressure sensors for two hydraulic pumps. The load data were measured during plow tillage for four speed stages: F2 (2.78 km/h), F5 (5.35 km/h), F7 (7.98 km/h), and F8 (9.75 km/h). Aspects of the gear-strength such as bending stress, contact stress, and safety factors were analyzed under two torque conditions: the equivalent torque at the highest plow load for the F8 speed stage and the maximum engine torque. The simulation results using KISSsoft showed that the maximum engine torque conditions had a lower safety factor than did the highest equivalent torque condition. The bending safety factors were > 1 at all gear stages, indicating that gear breakage did not occur under actual measured operating conditions, nor under the maximum torque conditions. However, the equivalent torque condition in the contact stress safety factor was > 1, and the maximum torque condition was < 1 at the first gear pair. The method of analysis using the equivalent torque showed lower stress and higher safety factor than did the method using maximum torque. Therefore, when designing a tractor by applying actual working torque, equivalent torque method would support more reliable product development.

• Journal of the Institute of Convergence Signal Processing
• /
• v.18 no.1
• /
• pp.6-12
• /
• 2017

In this paper, we proposed IoT based Smart Health Service using Motion Recognition for Human UX/UI. Until now, sensor networks using M2M-based u-healthcare are using non-IP protocol instead of TCP / IP protocol. However, in order to increase the service utilization and facilitate the management of the IoT-based sensor network, many sensors are required to be connected to the Internet. Therefore, IoT-based smart health service is designed considering network mobility because it is necessary to communicate not only the data measured by sensors but also the Internet. In addition, IoT-based smart health service developed smart health service for motion detection as well as bio information unlike existing healthcare platform. WBAN communications used in u-healthcare typically consist of many networked devices and gateways. The method proposed in this paper can easily cope with dynamic changes even in a wireless environment by using a technology supporting mobility between WBAN sensor nodes, and systematic management is performed through detection of a user's motion.

• Korean Journal of Agricultural Science
• /
• v.46 no.1
• /
• pp.57-65
• /
• 2019

The purpose of this study was to develop an environment field monitoring system to measure crop growth. The environment field monitoring system consisted of sensors, a data acquisition system, and GPS. The sensors used in the environment field monitoring system consisted of an ambient sensor, a soil sensor, and an intensity sensor. The temperature and humidity of the atmosphere were measured with the ambient sensor. The temperature, humidity, and EC of the soil were measured with the soil sensor. The data acquisition system was developed using the Arduino controller. The field monitoring data were collected before a rainy day, on a rainy day, and after the rainy day. The measured data using the environment field monitoring system were compared with the Daejeon regional meteorological office data. The correlation between the data from the environment field monitoring system and the data from the Daejeon regional meteorological office was analyzed for performance evaluation. The correlation of the temperature and humidity of the atmosphere was analyzed because the Daejeon regional meteorological office only provided data for the temperature and humidity of the atmosphere. The correlation coefficients were 0.86 and 0.90, respectively. The result showed a good correlation between the data from the environment field monitoring system and the data from the Daejeon regional meteorological office. Therefore, the developed system could be applied to monitoring the field environment of agricultural crops.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.358-363
• /
• 2019

In this paper, we implemented a welfare system for the elderly living alone, disabled, or babies to provide fast incident response in case of emergency situations. The proposed system can quickly recognize emergency situations using heart rate sensors and real-time image sharing. The sensors attached on a wrist band monitor the heart rate along with relevant bio signals of clients and send alarms to guardians in the emergency situations. At the same time, the real-time image signals are captured using OpenCV and sent to the guardians in order to give the exact information for fast and appropriate response to handle the situation. In the proposed system, the camera works only in the emergency situations so as to provide enough privacy to the client's every day life.

• Applied Chemistry for Engineering
• /
• v.34 no.1
• /
• pp.9-14
• /
• 2023

In this work, we developed a Nafion polymer-coated impedance sensor with two gold electrode configurations to measure the ion concentration in solution samples. The gold electrodes were fabricated through the sputtering process, followed by surface modification using Nafion polymer. The resulting sensors enable the prevention of the polarization phenomenon on the electrode surface, resulting in stable measurement of electrochemical signals. Spectroscopy and scanning electron microscopy measurements revealed that the thin film of Nafion was coated uniformly onto the surface of the gold electrode. The Nafion-coated sensor exhibited more stable impedance signals than the conventional gold electrode. It showed a highly reliable calibration curve (R² = 0.983) of the impedance sensor using a standard sodium chloride solution. In addition, a comparison experiment between the impedance sensor and a commercial conductivity sensor was performed to measure the ion concentration of artificial tears, showing similar results for the two sensors.

• Journal of Hydrogen and New Energy
• /
• v.34 no.1
• /
• pp.59-68
• /
• 2023

In this study, the performance of high-pressure fuel pumps was compared to find a high-pressure pump suitable for dimethyl ether (DME) fuel, and to establish a database of basic data on flow rates. The use of DME in compression ignition engines can reduce pollutant emissions. The cetane value of DME is higher than that of diesel fuel. The physical properties of DME are similar to liquefied gasoline gas (LPG), and when pressurized at a pressure of 6 bar or more, it changes from gas to liquid. Two types of high pressure pumps used in this study were independent injection type pump and a wobble plate type pump. Two high-pressure pumps with different injection types were compared. By measuring and comparing the performance changes of the two high-pressure pumps, a pump suitable for DME was selected and performance improvement measures were proposed. The changed experimental conditions to measure the performance change of the high pressure pump were increased in the units of 100 to 1,000 rpm and 100 rpm, and the experiment was performed at common rail pressures 300 and 400 bar. it was confirmed that the DME inside the fuel supply system remained in a liquid state through temperature sensors, pressure sensors, and pressure gauges. As a result of the experiment, it was confirmed that the flow rate discharged from the high-pressure fuel pump increased as the motor rotational speed increased, and the flow rate of the high-pressure fuel pump

• Journal of Biosystems Engineering
• /
• v.37 no.4
• /
• pp.225-232
• /
• 2012

Purpose: Accurate monitoring of information from various agricultural vehicles is one of the most important factors for appropriate management strategy of field operations. While there has been a number of study and design on applications of sensors and actuators for data acquisition and control system in tractor, incompatibility between various customized hardware and software has become a major obstacle to the universal deployment in real field operation. International standard for implementation of electronic control unit (ECU) in agricultural vehicles has becoming a mandatory requirement for inter-operation compatibility in the international trade of agricultural vehicle industries. The ISO 11783 standard is basically based upon well known communication technology designated using the controller area network (CAN) bus. While CAN bus could provide 1.0 Mbps of communication speed, the standard only recommended 250 kbps. Methods: This study presents the implementation and evaluation of ISO 11783 for tractor electronic control units (TECU)with a higher transmission rate from multiple ECU than 250 kbps. Throughput and loss rate of the developed prototype were calculated across manipulated bus load for laboratory experimental tests, and the maximum requirement of transmission rate by ISO 11873 was satisfied with lower than 60% of bus load. Results: Field tests with a TECU implemented to process messages from global positioning system (GPS) receiver resulted that the root mean square error of position information was lower than 4 m with 0.5 m/s as a travelling speed. Conclusions: Results of this study represent the utilization of the international standard ISO 11783 to providepractical developments in terms with the inter-operability of TECU.

• Safety and Health at Work
• /
• v.7 no.4
• /
• pp.347-353
• /
• 2016

Background: This study aimed to investigate the relation between key strike forces and musculoskeletal symptoms (MSS). Moreover, this study presents a key strike force measurement method to be used in a workplace setting. The correlation between key strike force characteristics and MSS was previously studied, but the measurement methods used either a single-key switch or force platforms applied under the keyboard. Most of the studies were conducted in a laboratory setting. The uniqueness of measurement methods in the current study is their ability to measure forces applied to a specific key in a workplace setting and to provide more information about specific key strike forces during typing. Methods: Twenty-four healthy computer workers were recruited for the study. The demographic questionnaire, and self-reported questionnaires for psychosocial status (General Nordic Questionnaire for Psychological and Social Factors at Work) and for detecting MSS were filled up, which later helped in dividing the participants into two groups (12 participants with pain and 12 without pain). Participants typed a predetermined text that utilized the instrumented keys multiple times. The dynamic forces applied to the keys were recorded and collected, using four thin and flexible force sensors attached to the preselected keys according to their location. Results: The results demonstrated that participants with high levels of MSS, specifically in the back and neck, in the last year exerted significantly higher key strike forces than those with lower levels of symptoms (p < 0.005). Conclusion: The key strike force exerted while typing on a keyboard may be a risk factor for MSS, and should therefore be considered in ergonomic evaluations and interventional programs.