• Transactions on Electrical and Electronic Materials
• /
• 제5권1호
• /
• pp.7-10
• /
• 2004

A new method for fabrication of transistor like structure of the bifacial solar cell using spin-on doping and electroless plating has been proposed and the basic characteristics of the bifacial cell have been investigated. It is found that 9％ increase in short circuit current is achieved with bifacial connection than the unifacial connection. Some unwanted effect of the series resistance on collection efficiency under different mode of illumination has been pointed out. Loss mechanisms inherent in the transistor like bifacial structure have also been discussed.

• 한국재료학회지
• /
• 제30권5호
• /
• pp.262-266
• /
• 2020

In this paper, we investigated the effect of the passivation stack with Al₂O₃, hydrogenated silicon nitride (SiN_x:H) stack and Al₂O₃, silicon oxynitride (SiON_x) stack in the n type bifacial solar cell on monocrystalline silicon. SiNx:H and SiON_x films were deposited by plasma enhanced chemical vapor deposition on the Al₂O₃ thin film deposited by thermal atomic layer deposition. We focus on passivation properties of the two stack structure after laser ablation process in order to improve bifaciality of the cell. Our results showed SiN_x:H with Al₂O₃ stack is 10 mV higher in implied open circuit voltage and 60 ㎲ higher in minority carrier lifetime than SiON_x with Al₂O₃ stack at Ni silicide formation temperature for 1.8% open area ratio. This can be explained by hydrogen passivation at the Al₂O₃/Si interface and Al₂O₃ layer of laser damaged area during annealing.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.31-41
• /
• 2016

n-type PERT (passivated emitter, rear totally diffused) bifacial solar cells with boron and phosphorus diffusion as p+ emitter and n+ BSF (back surface field) have attracted significant research interest recently. In this work, the influences of wafer thickness, bulk lifetime, emitter, BSF on the photovoltaic characteristics of solar cells are discussed. The performance of the solar cell is determined by using one-dimensional solar cell simulation software PC1D. The simulation results show that the key role of the BSF is to decrease the surface doping concentration reducing the recombination and thus, increasing the cell efficiency. A lightly phosphorus doped BSF (LD BSF) was experimentally optimized to get low surface dopant concentration for n type bifacial solar cells. Pre-oxidation combined with a multi-plateau drive-in, using limited source diffusion was carried out before pre-deposition. It could reduce the surface dopant concentration with minimal impact on the sheet resistance.

• Current Photovoltaic Research
• /
• 제9권4호
• /
• pp.111-122
• /
• 2021

Silicon heterojunction technology (HJT) solar cells have received considerable attention due to advantages that include high efficiency over 26%, good performance in the real world environment, and easy application to bifacial power generation using symmetric device structure. Furthermore, ultra-highly efficient perovskite/c-Si tandem devices using the HJT bottom cells have been reported. In this paper, we discuss the unique feature of the HJT solar cells, the fabrication processes and the current status of technology development. We also investigate practical challenges and key technologies of the HJT solar cell manufacturers for reducing fabrication cost and increasing productivity.

• Current Photovoltaic Research
• /
• 제7권4호
• /
• pp.97-102
• /
• 2019

Bifacial and semitransparent hydrogenated amorphous silicon (a-Si:H) thin-film solar cells in p-i-n configuration were prepared with front and rear transparent conducting oxide (TCO) electrodes using plasma-enhanced chemical vapor deposition method. Fluorine-doped tin oxide and tin-doped indium oxide films were used as front and rear TCO contacts, respectively. Film thickness of intrinsic a-Si:H absorber layers were controlled from 150 nm to 450 nm by changing deposition time. The dependence of performance characteristics of solar cells on the front and rear illumination direction were investigated. For front illumination, gradual increase in the short-circuit current density (J_SC) from 10.59 mA/㎠ to 14.19 mA/㎠ was obtained, whereas slight decreases from 0.83 V to 0.81 V for the open-circuit voltage (V_OC) and from 68.43% to 65.75% for fill factor (FF) were observed. The average optical transmittance in the wavelength region of 380 ~ 780 nm of the solar cells decreased gradually from 22.76% to 15.67% as the absorber thickness was changed from 150 nm to 450 nm. In case of the solar cells under rear illumination condition, the J_SC increased from 10.81 to 12.64 mA/㎠ and the FF deceased from 66.63% to 61.85%, while the V_OC values were maintained at 0.80 V with increasing the absorber thickness from 150 nm to 450 nm. By optimizing the deposition parameters, a high-quality bifacial and semitransparent a-Si:H solar cell with 350 nm-thick i-a-Si:H absorber layer exhibited the conversion efficiencies of 7.69% for front illumination and 6.40% for rear illumination, and average visible optical transmittance of 17.20%.