• 치위생과학회지
• /
• 제18권1호
• /
• pp.42-49
• /
• 2018

The computer-aided design/computer-aided manufacturing (CAD/CAM) system was introduced to shorten the production time of all-ceramic restorations and the number of patient visits. Among these types of ceramic for dental CAD/CAM, they have been processed into inlay, onlay, and crown shapes using leucite-reinforced glass-ceramics to improve strength. The purpose of this study was to observe the mechanical properties and microstructure of leucite-reinforced glass-ceramics for dental CAD/CAM. Two types of leucite-reinforced glass-ceramic blocks (IPS Empress CAD, Rosetta BM) were prepared with diameter of 13 mm and thickness of 1 mm. Biaxial flexural testing was conducted using a piston-on-three-ball method at a crosshead speed of 0.5 mm/min. Weibull statistics were used for the analysis of biaxial flexural strength. Fracture toughness was obtained using an indentation fracture method. Specimens were observed by field emission scanning electron microscopy to examine the microstructure of the leucite crystalline phase after acid etching with 0.5% hydrofluoric acid aqueous solution for 1 minute. The results of strength testing showed that IPS Empress CAD had a mean value of $158.1{\pm}8.6MPa$ and Rosetta BM of $172.3{\pm}8.3MPa$. The fracture toughness results showed that IPS Empress CAD had a mean value of $1.28{\pm}0.19MPa{\cdot}m^{1/2}$ and Rosetta BM of $1.38{\pm}0.12MPa{\cdot}m^{1/2}$. The Rosetta BM sample exhibited higher strength and fracture toughness. Moreover, the crystalline phase size and ratio were increased in the Rosetta BM sample. The above results are expected to elucidate the basic mechanical properties and crystal structure characteristics of IPS Empress CAD and Rosetta BM. Additionally, they will help develop leucite-reinforced glass-ceramic materials for CAD/CAM.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1774-1779
• /
• 2005

Most of materials receive force in using, therefore, the characteristics of materials must be considered in system design not to occur deformation or destruction. Mechanical properties about materials can be expressed as responsible level of material itself under the exterior operation. Main mechanical properties is strength, hardness, ductility and stiffness etc. Currently, among major measure facilities to measure such mechanical properties, advanced indentation technique has focused in industrial areas as reason of nondestructive and easy applications for mechanical tensile properties and evaluation of residual stress of materials. This study is to find the optimum experimental condition about residual stress advanced indentation technique for accurate analysis of the welded joint of steel materials through indentation load-depth curve obtained from cruciform specimen experiment. Optimum selection was applied to the welded joint of real steel materials to give non-equi-biaxial stress state and compared with general residual stress analyzing method for verification.

• 전자공학회논문지SC
• /
• 제45권1호
• /
• pp.50-56
• /
• 2008

본 논문에서는 롤(Roll)에 누워 있는 피검자의 각도와 가속도 신호를 측정하기 위한 디지털 경사계 설계하였다. 개발된 시스템은 기울기 센서(tilt sensor), 2축 가속도 센서(biaxial accelerometer), 마이크로프로세서(single chip microprocessor)와 블루투스(BlueTooth module)로 구성된다. 개발된 디지털 시스템은 다루기 쉽고 쉽게 착용 할 수 있다. 시스템을 성능을 평가하기 위해서 Roll위의 3명의 피검자로부터 각도와 가속도 신호는 ZEBRIS와 디지털 경사계에 의해서 동기화하여 측정하였다. 측정된 신호는 정량적인 방법에 의해서 처리되며 그때의 상관계수가 0.93임을 보여 준다. 이와 같은 결과로부터 디지털 경사계는 몸의 움직임을 평가하는데 유용할 것으로 보여 진다.

• Advances in nano research
• /
• 제7권6호
• /
• pp.405-417
• /
• 2019

This research is devoted to study post-buckling analysis of functionally graded carbon nanotubes reinforced composite (FG-CNTRC) micro plate with cut out subjected to magnetic field and resting on elastic medium. The basic formulation of plate is based on first order shear deformation theory (FSDT) and the material properties of FG-CNTRCs are presumed to be changed through the thickness direction, and are assumed based on rule of mixture; moreover, nonlocal Eringen's theory is applied to consider the size-dependent effect. It is considered that the system is embedded in elastic medium and subjected to longitudinal magnetic field. Energy approach, domain decomposition and Rayleigh-Ritz methods in conjunction with Newton-Raphson iterative technique are employed to trace the post-buckling paths of FG-CNTRC micro cut out plate. The influence of some important parameters such as small scale effect, cut out dimension, different types of FG distributions of CNTs, volume fraction of CNTs, aspect ratio of plate, magnitude of magnetic field, elastic medium and biaxial load on the post-buckling behavior of system are calculated. With respect to results, it is concluded that the aspect ratio and length of square cut out have negative effect on post-buckling response of micro composite plate. Furthermore, existence of CNTs in system causes improvement in the post-buckling behavior of plate and different distributions of CNTs in plate have diverse response. Meanwhile, nonlocal parameter and biaxial compression load on the plate has negative effect on post-buckling response. In addition, imposing magnetic field increases the post-buckling load of the microstructure.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제4B권4호
• /
• pp.157-169
• /
• 2004

Motor & generator operation at widely variable speeds is needed in various applications but hybrid and electric vehicle (HEV) stand out today, as quite a few companies are launching this year their mass production of HEVs. The quest for better starter-generators is far from ended, though. The present review paper unfolds a comparative critical evaluation of various starter-generators and their control for HEV. Induction, interior PM synchronous, transverse-flux PM synchronous, switched reluctance, together with claw-pole and biaxial excitation PM synchronous (BEGA) configurations with their control are all considered in system evaluations.

• 소성∙가공
• /
• 제28권6호
• /
• pp.361-367
• /
• 2019

Microstructure evolution and tensile properties of Al-8mass%Mg alloy casting billet by biaxial alternative forging were investigated in this study. An alternative forging system tailored in this study was used to allow continuous strain accumulations on the alloy workpiece. A finite element (FE) simulation results revealed that the strain was mainly concentrated in the core and that the shear bands developed into a form with an X shape in the cross-section of workpiece after the alternative forging using octangular rod shaped dies. With increasing the forging passes, it was observed that the Al-8mass%Mg alloy workpieces were significantly deformed, and cracks began to form and propagate on the both ends of the forged workpieces after five passes at room temperature. In as-forged microstructures taken by microscopes, twins, clustering of dislocations, and fine subgrains were found. Tensile strengths of the forged specimens showed significant increases depending on the number of forging passes, and a trade-off relationship was observed between the elongation and strength. At room temperature and 100℃ the workpieces showed similar behaviors in microstructural evolution and tensile properties depending on forging passes, while the increase range in strength was reduced at 200℃.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2019년도 춘계학술대회
• /
• pp.436-438
• /
• 2019

에어하키 로봇은 머신 비전 시스템으로 하키 공을 카메라를 통해 인식하여 사용자와 플레이를 할 수 있다. 하키 공의 위치 감지는 OpenCV 라이브러리를 사용하여 공의 색 정보를 이용하여 인식하게 구현하였다. 하키 공의 위치를 감지하고 또한 그 궤적을 예측하여 결과를 ARM Cortex-M 보드로 전송한다. ARM Cortex-M보드는 2축 직교 로봇을 제어하여 에어 하키 경기를 진행한다. 에어 하키 로봇의 전략에 따라 수비, 공격, 수비과 공격 모드로 동작시킬 수 있다. 본 논문에서는 비전 시스템 개발과 궤적 예측 시스템에 관해 기술하고 에어 하키 경기를 진행하는 2축 직교 로봇을 제어하는 새로운 방법을 제시한다.

• 대한조선학회논문집
• /
• 제55권6호
• /
• pp.521-526
• /
• 2018

The doubler plate design system for the reinforcement of the ship plate members was developed considering various loads that subjected to the in-plane biaxial load, the in-plane shear load and out-of-plane load. The author summarized the accuracy of the development formula and equations through the equivalent plate thickness concept and finally introduced the new design system of doubler plate reinforcement. Through this study, it can be considered as an initial design guideline based on ship doubler plate reinforcement strength at areas without repeated load, or an initial structure analysis model for final structural design.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.64-66
• /
• 2007

In this paper, a digital inclinometer to measure the angle and acceleration signals of subject laid on Roll was designed. The designed system consists of a tilt sensor, biaxial accelerometer, microcontroller and BlueTooth module. The designed digital inclinometer was easy to handle and easy to wear. To evaluate the performance of the system, we measured simultaneously the angle and acceleration signals from the 3 subjects on the Roll with two instruments which are ZEBRIS and our system. The measured signals were processed by statistical method and then the correlation coefficient of 0.93 was shown. From the results, the designed digital inclinometer is shown to be useful in assessment of body movement.

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.64-71
• /
• 2004

The growing need for higher precision and productivity in manufacturing industry has lead to an increased interest in computer numerical control (CNC) systems. It is well known fact that the cross-coupling controller (CCC) is an effective method for contouring applications. In this paper, a multi-axis contour error controller (CEC) based on a contour error vector using parametric curve interpolator is introduced. The contour error vector is a vector from the actual tool position to the nearest point on the desired path. The contour error vector is the closest error model to the contour error. The simulation results show that the CEC is more accurate than the conventional CCC for a biaxial motion system. In addition, the experimental results on 3-axis motion system show that the CEC is simply applied to 3-axis motions and contouring accuracy is significantly improved.