• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.429-430
• /
• 2006

To estimate the fatigue life of flange-shaft assembly, fatigue test for flange material and bending fatigue test for flange-shaft assembly were conducted. Also, finite element analysis for flange-shaft assembly was conducted. Then, we have changed the obtained P-N curve to S-N curve using the finite element analysis results which were stress values at the location of fracture. The S-N curve of flange material itself was almost consistent with that of flange-shaft assembly, so it seems that the fatigue life of flange-shaft assembly could be estimated by using S-N curve for flange material and the stress at the location of fracture calculated by finite element methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.129-130
• /
• 2006

This paper presents a study on the effect of feedrate changes on the fatigue life of Al 7075-T6 specimens before and after shotpeening. For this purpose. five groups of specimens, each of which consists of eight specimens, were first machined at five different feedrates (0.05, 0.10, 0.15, 0.20 0.25 mm/rev). Half of eight specimens in each group were then peened and the others remained un-peened Finally, the fatigue life of each specimen was measured by using 4-point rotatry bending machine. Comparison of fatigue life among ten sets of specimens is presented.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.337-342
• /
• 2000

Experimental investigations were carried out to find the characteristics of grinding of ceramics. Grinding mechanisms of ceramics were inspected through the microscopic examination. It has been found that the specific grinding energy of ceramics is relatively low as compared to that of steels. The specific grinding energy affects the surface roughness and the residual stress of ground surface. The experimental results indicate that the rougher surface finish and higher compressive residual stress are obtained at lower specific grinding energy. The surface roughness and the residual stress of the ground surface have significant effects on the strength of ground piece of ceramics.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.78-84
• /
• 1997

Friction welding technique was studied to weld the turbine wheel and shaft of a turbocharger. The welding parameters were selected to investigate the effects of variables on welding quality of Inconel 713C and SCM 440. Experimental results showed that the turbine wheel and shaft could be successfully welded by friction welding. The heat affected zone was identified to be 2 mm from the weld seam. After welding, the hardness profile was found to have sudden increase and decrease for inconel 713C and SCM 440 respectively. Tensile strength of welded specimens was higher than the required strength for all of the studied welding parameters. The central portion of fracture surfaces by bending had no defects such as crack.

• Journal of Welding and Joining
• /
• v.16 no.2
• /
• pp.57-63
• /
• 1998

This study deals with the friction weldability of machine structural carbon steel (SM45C) to Al-Mg-Si aluminium alloy (A6063). The bonding strength of friction welded joints, from all mechanical test, exceeded that of A6063 base metal, under the condition of friction time 1.5 sec, upset pressure 80MPa. The friction welded joints under these conditions exhibited tensile strength of 262MPa, bending angle of 90$^{\circ}$ without crack at weld interface and shear strength of 113MPa. Consequently, the friction weldability of SM4C to A6063 was very excellent, and that was possible without special preparation of weld surfaces.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.10 no.2
• /
• pp.9-18
• /
• 1973

The effects of carburization on the fatigue strength and cracks were studied. The fatigue phenomena of the carburized specimens were compared with noncarburized specimens those were either heat-treated or un-treated. The fatigue strength of these specimens were measured by rotating bending fatigue machine. The obtained results indicated that the fatigue strength of carburized specimens were increased ranging from 24-59 % than those of un-treated, and 22-38% than those of heat-treated. The Vickers hardness of carburized were also increased as much as 138-195% than those of un-treated, and 42-125% than those of heat-treated. The microscopic observation of the carburized specimens mostly composed of minute pearlitic structure at hard case exhibited to have more localized slip than those of non-carburized specimens.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.47-54
• /
• 2003

The rotating of rotatory unit with its structural unbalance mass and laundry is making the main vibration problem in a vertical axis washing machine. For reducing vibration problem total washing system hung on the case by its suspension system which is constitute of spring, damper and suspension bar and hydraulic balancer is attached at the upper rim of spin basket. In this paper, we make the dynamic model of washing system of its rigid body motions by 6 degree of freedoms. Hydraulic balancer is modeled by one degree of freedom like auto ball balancer. Elastic motions of washing system have found by method of analytic, experimental and FEM. And we consider first bending mode of each suspension bar and first circumferential mode of assy tub. So, the total washing system is modeled by 12 degree of freedoms. Equations of motion for total washing system have derived, and we perform the dynamic simulation tests.

• Advanced Composite Materials
• /
• v.17 no.4
• /
• pp.319-332
• /
• 2008

The thermoelastic behaviors of an inflatable fabric membrane structure for use in a stratospheric airship envelope are experimentally and numerically investigated. Mechanical tensile properties of the membrane material at room, high, and low temperatures are measured using an $Instron^{(R)}$ universal testing machine and an $Instron^{(R)}$ thermal chamber. To characterize the nonlinear behavior of the inflated membrane structure due to wrinkling, the bending behavior of an inflated cylindrical boom made of a fabric membrane is observed at various pressure levels. Moreover, the envelope of a stratospheric airship is numerically modeled based on the thermoelastic properties of the fabric membrane obtained from experimental data, and the wrinkled deformed shape induced by a thermal load is analyzed.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1130-1135
• /
• 2004

The vertical roller mill is the important machine grinding and mixing various crude materials in the manufacturing process of portland cement. Vertical roller mill is subjected to the cyclic bending stress by rollers load. It demands $4{\times}10^7$ cycle but has $4{\times}10^6{\sim}8{\times}10^6$ cycle. It fractures at the edge of grinding path of outside roller. The repair expense for it amounts to 30% of total maintenance. Therefore, this study shows optimal design for vertical roller mill using DOE and neural network.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.308-313
• /
• 2002

In order to investigate the characteristics of grinding and diamond wheel grinding ceramic materials, grinding resistance, surface roughness of worked surface and image of grinding wheel were acquired using experimental method. Through the experiments, this makes it possible to observe grinding wheel behavior by grinding resistance, surface roughness and cutting edge ratio. In case of A1$_2$O$_3$, cutting edge ratio is begger than that of ZrO$_2$and Si$_3$N$_4$. That's because A1$_2$O$_3$has a characteristics of low fracture toughness and bending stress.