• 한국농공학회논문집
• /
• 제51권3호
• /
• pp.71-78
• /
• 2009

Pipe section of bending part at the arch type pipe-house showed an ellipse with oblateness of 0.076 on the average. Flexural rigidity of bending part decreased by average 6.3% than that of an original round shape section. The deflection of arch type pipe-house measured by model experiments showed much bigger than the result of structural analysis. In case of arch type pipe-house, we supposed that the decrease of flexural rigidity for the bending part of pipes had an effect on deflection of roof under the working load. This effect should be considered in the structural analysis. Bending resistance of gable type pipe-house used a prefabricated connector which developed in this study showed about $1.5{\sim}1.8$ times stronger than that of the existing arch type or gable type processed bending. Therefore, we supposed that the gable-roofed prefabricated pipe-house is safer than arch type or bent gable type in case of heavy snowfall. According to house scales and section properties of steel pipe in use, safe snow depths and rafter intervals were presented for design of gable-roofed prefabricated pipe-house. Their standards were established in the range of the durable models recommended by RDA, and the comparative examinations were conducted by means of structural analysis. It was evaluated that the developed greenhouse model had a high applicability in the field.

• 마이크로전자및패키징학회지
• /
• 제18권1호
• /
• pp.55-59
• /
• 2011

유연성 기판 상의 동박의 반복 굽힘 변형에 따른 절곡 빛 굴곡 신뢰성과 인장 특성과의 관계를 규명하기 위해 4종류의 동박 시편의 절곡 신뢰성 실험, 굴곡 선뢰성 실험과 인장 실험을 실시하였다. 절곡 신뢰성 실험은 동박에 5.3%의 굽힘 변형률을, 굴독 선뢰성 실험은 동박에 2.0%의 굽힘 변형률을 반복적으로 인가하면서 전기 저항 변화를 관찰하고 피로 수명을 평가하였다. 또한, 4가지 시편의 인장 실험을 통해 탄성 계수, 항복 강도, 연장 강도, 인성 등의 재료 물성을 구한 결과, 연성과 인성이 우수한 시편의 경우 절곡 및 굴곡 신뢰성이 크게 우수한 것으로 나타났다. 반면, 탄성 계수, 항복 강도의 경우 절곡 및 굴곡 신뢰성과 큰 연관성을 보이지 않았다. 이는 절곡 및 굴곡 변형에 의한 금속의 피로 파괴 거동은 재료의 파괴 인성과 밀접한 관계를 가지기 때문으로 판단된다.

• 대한정형도수물리치료학회지
• /
• 제27권2호
• /
• pp.37-43
• /
• 2021

Background: The purpose of this study is to compare and analysis the changes in strength and endurance of the knee extensor muscles after Anterior cruciate ligament reconstruction. Methods: Twelve male subjects with ligament injury were seated on Biodex and the hip joint was flexed at 110°, and torso, lower extremities, and legs were fixed using Velcro. The resistance device was placed at a point 3cm above the ankle, and measurements were taken before and a surgery at 60°/sec and 180°/sec when the knee was maximally extended. The postures ingeniously combine forward-bending poses countered with backward-bending ones. Results: There was no significant difference in the comparison of muscle strength of 60°/sec and 180°/sec before surgery. But there was a significant difference after surgery. There was significant difference in muscle endurance both before and after surgery. There was a significant difference in the pre- and post- operative comparison values of muscle strength and endurance in isokinetic movements at 60°/sec and 180°/sec during knee extension on the injured side. Conclusion: For cruciate ligament tears, Orthopedic reconstruction is recommended. Correct alignment of the knee ligament after surgery can enhance the strength and endurance of the quadriceps femoris during knee extension rejuvenated.

• 구강회복응용과학지
• /
• 제25권4호
• /
• pp.349-360
• /
• 2009

목적: 임플란트 보철 수복에서 심미적 요구도가 증진되면서 최근에는 고강도, 고인성을 지니면서 생체적합성 우수하고 치아의 색과 조화로운 지르코니아 지대주의 사용이 증가하는 추세이다. 몇몇 임상보고를 통해 지르코니아 지대주의 우수한 주위조직 반응과 단기간의 성공적인 결과가 보고 되었으나, 장기간의 안정성을 평가하는 기계적 강도에 관한 연구는 미흡한 실정이다. 이에 본 연구에서는 직경, 각도, 연결방식이 상이한 임플란트 고정체 - 지르코니아 지대주의 단순 파절강도와 반복하중에 의한 피로한계 측정을 통해 지르코니아 지대주의 기계적 안정성을 평가해 보고자 하였다. 재료와 방법: ISO규정에 따라 지르코니아 지대주-고정체를 변연골이 3mm 흡수된 조건에서 $30^{\circ}$경사하중으로 압축굽힘강도를 측정하고, 그 값의 80%를 최대하중으로 10%를 최소하중으로 하여 10Hz의 sine형 반복하중을 $5{\times}10^6$ 주기를 초과하는 조건의 내구성한계를 측정하였다. 지르코니아 지대주로는 regular diameter를 가지면서 external butt joint의 straight 지대주와 $17^{\circ}$ angled 지대주, 그리고 narrow diameter 이면서 external butt joint의 straight 지대주와 internal conical joint의 straight 지대주를 사용하였다. 압축굽힘강도 값을 일원분산분석과 사후검정으로 검증하였으며, 피로파절면을 전자주사현미경을 통해 관찰했다. 결과: 압축굽힘강도는 최소 927N 이상으로, 직경의 차이에 따른 유의한 차이를 보였으며( P<.05), 내구성 한계는 503N에서 868N까지의 번위를 보였다. 결론: 지르코니아 지대주는 구강내 기능하중을 견딜수 있는 적절한 기계적 강도를 가지는 것으로 판단된다.

• 열처리공학회지
• /
• 제6권3호
• /
• pp.166-177
• /
• 1993

Bending fatigue strength tests were made for VC coated die steels which were coated by immersing in a molten borax bath and for hardened die steels which were quenched and tempered, in order to clarify the effect of VC coating at $1000^{\circ}C$ and $1025^{\circ}C$. The material used in this investigation was a representative cold and hot die steels STD11, STD61. The results obtained are as follows. 1) The endurance limit of VC coated die steels was a little lower than that of hardened die steels. It is considered to be mainly due to the decfl.lase of hardness in the substrates. Accordingly, the endurance limit reo covered almost to the level of hardened die steels by an additional diffusion treatment. 2) The initiation point of fatigue fracture of VC coated die steels in reversed bening was on the substrate just under the VC layer. Hence, the endurance limit is corrected to the hardness of this part. 3) But, there is a considerable scatter in this relationship and the endurance limit of VC coated die steels was a little lower than that of hardened die steels with equal hardness. These results suggest that the fatigue strength of VC coated die steels is determined not only by the hardness but also by other factors. For example. the residual stress in the substrate just under VC coating layer is one of the factors besides hardness which is mainly related to the retained austenite(${\gamma}_R$).

• 한국기계연구소 소보
• /
• 통권13호
• /
• pp.3-13
• /
• 1984

Fatigue failure of axle housing could cause many injuries and much financial loss. This challenges the engineer to improve design decisions involving fatigue. Endurance evaluation of axle housing is great interest to auto-mobile manufacturers for the sake of safety and reliability. Axle housing is subjected to gross vehicle weight(G.V.W)as mean load and alternating load. Theoretical design diagram involving mean and alternating stresses is used for the evaluation of axle housing fatigue endurance with the equivalent stress of fatigue critical area on the axle housing. Four point bending fatigue tests on axle housing with constant amplitude loading at approximately R=0 were performed with 50 ton servohydraulic strucural fatigue testing machine developed at KIMM. Specimens were made with the same material STKM 13B as the axle housing and tested to obtain S_N data. Five specimens of STKM 13B were tested at 253.61 MPa and weibull distribution was obtained at the same stress level. Material data and structural data were compares and fatigue stress property factor and fatigue life property factor were obtained.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.64-72
• /
• 1976

This experimental work was carried out to investigate the fatigue bending strength on various shapes and sizes of notches of the domestically manufactured steel plate. The notch types tested were a circular hole, U-and V-notches. The S-N diagram for different notch shapes were discussed in relation to plan bending strength and stress concentration factor of notches .The results of the experiments are summarized as follows : (1) The difference between stress concentration factor and notch factor was greater as the radium of notch root became smaller, and these values approached to an identical value as the radium of notch root increased. (2) It was shown that the plane bending fatigue limit of bar without notch for the hotrolled steel having the tensile strength of 33.1kg/$mm^2$was 17.0kg/$mm^2$. (3) U-and V-notch had a greater effect of stress concentration factor on the endurance limit, but O-hole showed the same effect only for $\o\pm2mm$. (4) For the same radius of notch root, U-notch showed a lower value of fatigue limit compared to V-notch and O-hole.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.454-457
• /
• 2008

Effects of patenting temperature on bending fatigue resistance of pearlitic steel filaments were investigated experimentally. The fatigue resistance of steel filaments was carried out by using hunter machine, specially designed for ultra fine-sized steel wires, in the controlled conditions. The transmission electron microscopy (TEM) was used for observing the overall microstructure. It revealed that the fatigue resistance as well as tensile strength increased together with increase of patenting temperature from 510 to $600^{\circ}C$, while the endurance ratio ($\sigma_e/\sigma_{TS}$) of filaments decreased. It is believed that this variation of mechanical properties with change of patenting temperature should be strongly influenced by the change of microstructure. The bending fatigue properties of steel filaments were discussed based on microstructural parameters.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.399-403
• /
• 2002

The transmission system of high speed train serve in the severe condition compared with those of other trains, namely, they have to transmit high power to run with high speed and they have to make maximum use of the limited space. To clarify the strength of gear for Korea High-Speed Train, a bending fatigue test of gear specimen is performed and compare with actual gear's. From this result, specimen test is useful to infer S-N curve and endurance limit of actual gear that much time and expense are consumed.

• PNF and Movement
• /
• 제15권3호
• /
• pp.381-387
• /
• 2017

Purpose: Although some studies indicate that the Sorensen test may not be used to examine back muscles such as the erector spinae, alternatives to the back-extension test are rarely suggested. Therefore, the purpose of the present study was to investigate an effective way to stimulate the erector spinae muscles by adding a component of trunk rotation and lateral bending to general back extensions. Methods: A total of 18 healthy, physically active participants performed simple trunk extension, extension with trunk rotation, and extension with lateral bending. Surface electromyography responses of the latissimus dorsi, thoracic, and lumbar levels of the erector spinae; the gluteus maximus; and the biceps femoris muscles were investigated during these 3 conditions of modified back extension tests. Results: The simple trunk extension exercise caused significant increases in activity of the gluteus maximus and biceps femoris muscles as compared to the extension with rotation and lateral bending exercises. The extension with trunk rotation exercise showed significantly greater activation in the thoracic and lumbar levels of the erector spinae and in the latissimus dorsi as compared to the other exercises. The index measuring subjective difficulty was significantly lower in the simple trunk extension exercise as compared to the extension with trunk rotation and extension with lateral bending exercises. Conclusion: The present study suggests that extension with trunk rotation has the advantage of stimulating the para-spinal muscles, while simple trunk extension may not be adequate to selectively simulate the para-spinal muscles but may be appropriate for examining global trunk extensors.