• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.9
• /
• pp.1699-1701
• /
• 2010

The Active Noise Cancelling(ANC) headphone is now becoming commercially available. But it reduces not only noise but also information signals such as speech or some signals including audible information in particular situation. In this paper, we propose an ANC headphone using adaptive beam-forming techniques which cancels signals except the headphone wearer's look direction signal. It enables workers working in noisy condition to talk with their coworkers. Computer simulation is performed to show the effectiveness of a proposed algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.163-170
• /
• 2003

The back beam for a automotive bumper was roll formed to improve performance, reduce weight and save cost. For the back beams produced by conventional stamping and roll forming, the crashworthiness analyses were carried out by numerical simulation and real impact test. The characteristic properties and applicability of the roll formed back beam are discussed from the results of the analyses.

• Laser Solutions
• /
• v.2 no.1
• /
• pp.51-60
• /
• 1999

In this paper, weldability and formability of Tailored-Blank (TB) and the structural impact testing of bump beam were investigated to apply TB to automobile bumper beam. The optimal $CO_2$ laser welding condition for TB of SPFC and SPRC steel plates with different thicknesses was obtained. Before welding, the cross section of butt joint was prepared only by shearing without milling process. Real type bump beam was produced by two kind of forming processes such as roll-forming and press-forming, and the good formability of TB was obtained. Impact test results of bump by using pendulum and barrier were satisfied the impact regulation of bump. Finally. It may be confirmed that laser welded TB is well-balanced material in both weight reduction and production cost of automobile bump.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.3
• /
• pp.587-592
• /
• 2018

An adaptive beam forming system using a phased array antenna improves communication quality by beam forming adaptively to a communication environment having an interference signal. For adaptive beam forming, a good combination of the phases of the excited signals to each radiating element of the phased array antenna should be calculated. In this paper, improved particle swarm optimization algorithm that adds a re-spreading procedure according to particle density was proposed to increase the probability of good phase shift combination output.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.749-754
• /
• 2003

In this paper, we introduce the measurement of the underwater noise with 32channel hydrophone array of Samsung CAvitation Tunnel (SCAT) and the detection technique of noise sources by using the beam-forming method. Measurement and way signal Processing under fluid flow are essential works for the underwater acoustics, especially for the detection of noise sources. As the acoustic impedance of the water is relatively high and the tunnel is an enclosed system, we have to consider the interaction between tunnel and water together with the reflection of noise in the beam-forming technique. Also, for a hydrophone array system that is fixed on one side of tunnel wall as done in SCAT is liable to suffer from some limitations in the detection of the noise sources with the array, we discuss these limitations particularly on the frequency range and spacing of noise sources.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.715-730
• /
• 2019

We propose a switched beam-forming antenna that satisfies not only ultra-wideband characteristics but also beam-forming in the WLAN frequency band using an ultra-wideband antenna and passive parasitic elements applying a broadband optimal reactance load algorithm. We design a power and phase estimation function and an error correction function by re-analyzing and normalizing all the components of the parasitic array using control system engineering. The proposed antenna is compared with an antenna with a pin diode and reactance load value, respectively. The pin diode is located between the passive parasitic elements and ground plane. An antenna beam can be formed in eight directions according to the pin diode ON (reflector)/OFF (director) state. The antenna with a reactance load value achieves a better VSWR and gain than the antenna with a pin diode. We confirm that a beam is formed in eight directions owing to the RF switch operation, and the measured peak gain is 7 dBi at 2.45 GHz and 10 dBi at 5.8 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.7A
• /
• pp.603-610
• /
• 2005

Beam-forming method based on the estimated channel information at the base station degrade the performance mismatching directional vector in case of systems which Frequency Division Duplex (FDD) center frequency of uplink and downlink are different. Also blind estimation technique which is to obtain directional vector of reverse link through received signal has disadvantage of hardware complexity increase. To solve these problems, in present paper, a smart antenna algorithm which is to improve the beam-forming complexity increase due to user number by appling the spatial fourier transform to be able to beam- forming toward a wanted direction through adjusting a obtained uplink weight function by estimating Angle-of-Arrival (AoA) to the competable form at the downlink is proposed. The proposed algorithm is integrated to the CDMA downlink transmitter and simulations are performed to confirm the performance as frame error rate at the receiver. As a result, the beam forming effect is confirmed and the performance gain with the proposed algorithm is comparable to ordinary smart antenna system.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.20 no.1
• /
• pp.71-77
• /
• 2016

In this study, the seismic performance of connections between filled composite beam (CG beams) and forming angle composite (FAC) column was experimentally evaluated. First, the bending tests were conducted on two CG beams and the axial tests were conducted on two FAC columns. Then, based on these preliminary test results, the cyclic loading test were performed on two interior connections between CG beam and FAC column. The main difference of two specimens is the plate shape of the CG beam. The test results showed that both specimens achieved the maximum story drift capacity over 0.04 radian which is required for special moment frame.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.431-440
• /
• 2012

In this paper, new beam-forming array antenna is proposed. The proposed beam-forming array antenna has control ability for beam-direction/width by employing low loss reconfigurable power divide and three-dimensional array structure. The reconfigurable power divider is key idea in the proposed antenna, because it has reconfigurable RF power distribution ability to each antenna. And, for research and verification of the proposed antenna, 3-dimensional beam-forming array antenna is implemented, and the experimental results show that the proposed antenna has various radiation modes from 1:1 to 1:N by adjusting RF power distribution.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.62-67
• /
• 2003

This paper is concerned with the design of the beam forming module that is a key unit of the active phased array antenna(APAA) system for mobile satellite communications. This module includes two blocks for main signal and tracking signal. Main signal block has the role of transmitting input signal from phased array antenna to tracking signal block. And, tracking signal block executes main roles, beam forming of tracking signal and electronic beam control. The several electrical performances of this module, phase characteristics and linear gain, etc., agreed with specifications needed fur APAA, and for more clear verification of the performances, the satellite communication test of the APAA including the modules was accomplished in the outdoors.