• 한국분말재료학회지
• /
• 제29권4호
• /
• pp.314-319
• /
• 2022

The effect of the laser beam diameter on the microstructure and hardness of 17-4 PH stainless steel manufactured via the directed energy deposition process is investigated. The pore size and area fraction are much lower using a laser beam diameter of 1.0 mm compared with those observed using a laser beam diameter of 1.8 mm. Additionally, using a relatively larger beam diameter results in pores in the form of incomplete melting. Martensite and retained austenite are observed under both conditions. A smaller width of the weld track and overlapping area are observed in the sample fabricated with a 1.0 mm beam diameter. This difference appears to be mainly caused by the energy density based on the variation in the beam diameter. The sample prepared with a beam diameter of 1.0 mm had a higher hardness near the substrate than that prepared with a 1.8 mm beam diameter, which may be influenced by the degree of melt mixing between the 17-4 PH metal powder and carbon steel substrate.

• Applied Microscopy
• /
• 제36권spc1호
• /
• pp.25-33
• /
• 2006

Nanofabrication with finely focused ion and electron beams is reviewed, and position and size controlled fabrication of nano-metals and -semiconductors is demonstrated. A focused ion beam (FIB) interface attached to a column of 200keV transmission electron microscope (TEM) was developed. Parallel lines and dots arrays were patterned on GaAs, Si and $SiO_2$ substrates with a 25keV $Ga^+-FIB$ of 200nm beam diameter at room temperature. FIB nanofabrication to semiconductor specimens caused amorphization and Ga injection. For the electron beam induced chemical vapor deposition (EBI-CVD), we have discovered that nano-metal dots are formed depending upon the beam diameter and the exposure time when decomposable gases such as $W(CO)_6$ were introduced at the beam irradiated areas. The diameter of the dots was reduced to less than 2.0nm with the UHV-FE-TEM, while those were limited to about 15nm in diameter with the FE-SEM. Self-standing 3D nanostructures were also successfully fabricated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1089-1092
• /
• 2001

In the stereolithography process, build parameters are laser power, scan velocity, scan width, bean diameter, layer thickness and so on. These values are determined according to product accuracy and build time. Build time can be reduced by improving of scan velocity, laser power, layer thickness, hatching space and so on. But variation of these parameters influence part accuracy, surface roughness, strength. This paper observed cure properties in various beam diameter. In order to examine these, relationships of scan velocity and cure depth, scan velocity and cure width according to various beam diameter in one scan line are measured. And cure thickness is measured according to beam diameter and scan velocity in scan surface of one layer. For reduction of build time, beam diameter and scan velocity is proposed in stereolithography process.

• 한국광학회지
• /
• 제11권2호
• /
• pp.73-79
• /
• 2000

사출성형법으로 제조된 $fheta$렌즈를 주사렌즈로 상요하는 Laser Scanning Unit의 주주사 및 부주사 방향의 빔경을 측정했다. 주주사 빔경의 경우 $62muextrm{m}$~ $68\mu\textrm{m}$로써 설계치와 유사한 성능을 보이지만 부주사 빔경의 경우 $78\mu\textrm{m}$~$115\mu\textrm{m}$로써 꽤 큰 빔경편차( $37\mu\textrm{m}$)를 나타내었다. 사출성형렌즈에서는 냉각.고화시 수축에 의한 형상오차와 불균일 냉각에 의한 내부왜곡(복굴절)이 발생하게 되는데, 이는 결국 파면수차(빔경확대)를 발생시키게 되고 결국 레이저프린터의 화상열화로 나타나게 된다. 본 논문에서는 부주사 빔경편차의 주요인을 밝혀내기 위해 복굴절(편광비) 및 $f\theta$렌즈의 비구면 형상을 측정하였다. 그리고 측정된 비구면 형상치를 CODE-V(미국 ORA사의 광학설계 프로그램)에 입력하여 부주사 상면만곡을 계산하고, 이와 설계 초점심도를 비교.분석함으로써 복굴절이 부주사 빔경편차의 주요인임을 알 수 있었다.

• 한국가구학회지
• /
• 제13권2호
• /
• pp.11-18
• /
• 2002

This study was carried out to investigate the strength and technical feasibility of glulam from small diameter Pinus densiflora and Larix kaempferi. Small diameter logs are currently not used in structural laminated beam construction, but it is suggested that its properties may be feasible for this purpose. The glulam combinations were designed with high grade laminae located at outer laminations (face) and low grade laminae located at center laminations. Important problems of finger jointed glulam as a structural beam are the small modulus of rupture (MOR). One solution for this problem Mi to use veneer and solid wood as the face laminae. The MOE values were predicted for each beam from laminae. The results showed that actual beam MOE values exceeded slightly the predicted values. Based on the evaluation and analysis of Pinus and Larix glulam, the maximum load of Larix kaempferi glulam indicated large values. The bending properties of A and E types glulam were superior to others. It is suggested that this small diameter log can be a candidate for structural glulam construction, providing the proper combinations of face laminae.

• Structural Engineering and Mechanics
• /
• 제89권2호
• /
• pp.155-170
• /
• 2024

Several types of column-beam connections are used in the design of steel structures. This situation causes different cross-section effects and, therefore, different displacements and deformations. In other words, connection elements such as welds, bolts, continuity plates, end plates, and stiffness plates used in steel column-beam connections directly affect the section effects. This matter reveals the necessity of knowing the steel column-beam connection behaviours. In this article, behaviours of bolted column-beam connection with end plate widely used in steel structures are investigated comparatively the effects of the stiffness plates added to the beam body, the change in the end plate thickness and bolt diameter. The results obtained reveal that the moment and force carrying capacity of the said connection increases with the increase in the end plate thickness and bolt diameter. In contrast, it causes the other elements to deform and lose their capacity. This matter shows that optimum dimensions are very important in steel column-beam connections. In addition, it has been seen that adding a stiffness plate to the beam body part positively contributes to the connection's moment-carrying capacity.

• 한국안전학회지
• /
• 제20권4호
• /
• pp.54-62
• /
• 2005

This Study is to find out how RC beam mixed with sawdust acts comparing with normal beam without sawdust mixture, and how they can be applied to the actual structural frame, despite a Int that they are mixed with waste material : saying sawdust. ED3H1, ED3H2, ED5H1, ED5H2, ED3H1UB, ED5H1UB, ED3H2L, ED5H2L and Normal without sawdust mixture are main factor to be tested here in order to apply them to the actual case. D and H means diameter 3cm or 5cm, and holes one and two respectively. And all variables are tested with each two for one variables. Test results are compared using crack diagrams and strain & loads. There are eleven(11)% capacity decrease between ED 3H1 and ED5H1 in rebar, strain. Left and right side crack shapes are much similar in variable ED3H2L having maximum capacity 14.5 tone. ED5H2L having maximum capacity thirteen(13)tone, in case of normal 19.6 tone. Two holes in beam rather on the longitudinal direction than on the forcing direction can be more effective to keep the original capacity of the beam because this case can distribute load more uniformly. There is 33% capacity decreased in case of diameter five(5)cm, compared to diameter three(3)cm. Two holes give thirty nine(39) percent capacity decrease than one of diameter three(3)cm.

• 센서학회지
• /
• 제8권3호
• /
• pp.219-225
• /
• 1999

본 연구의 목적은 beam 지름이 12.5mm에서 40mm 까지의 소형 x-선에 대한 TMR, OAR, TSF를 전리함, 다이오드, 필름 및 TLD 등의 검출기로 측정하여 6MV 소형 x-선 beam 선량 측정에 적합한 검출기를 결정하였다. 가장 작은 beam인 지름 12.5mm beam의 TMR 값을 여러 가지 검출기로 측정한 결과 다이오드와 필름이 가장 우수하였으며 표준 TMR 값에 대한 오차 범위는 2% 이내였다. 그리고 이 다이오드와 필름은 OAR 측정 시공간 분해능이 뛰어났으며 이 두 검출기의 상대 비교에서 오차는 3% 이내였다. 이에 반해 전리함은 소형 beam의 TMR 및 OAR을 정밀하게 측정하는데 적합하지 않았다. beam 지름 12.5mm에서 40mm까지의 beam에 대한 TSF를 다이오드와 TLD로 측정한 결과 그 값은 $0.89{\sim}0.96$이었다. 그리고 beam 지름이 25mm 보다 크면 0.125cc 전리함 및 markus 전리함으로 측정한 TSF 값은 다이오드 및 TLD로 측정한 TSF 값과 잘 일치하였으며 그 오차 범위는 2% 이내였다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.76-80
• /
• 1989

Spatial filters were designed for 1 TW high power phosphate glass laser development. Laser beam should be expanded from 1 mm diameter to 200mm diameter. Pin hole size should be determined and most of incident energy should be transmitted through out to final spatial filter. Each pin hole size is determined by calculating encircled energy for Gaussian beam from the oscillator. The optical tube length of each spatial filter is corrected to have the best collimating quality by scew raytracing through the total system.

• 한국진공학회지
• /
• 제20권6호
• /
• pp.403-408
• /
• 2011

MFX tube를 개발하기 위하여, MFX tube 내에서 전계방출음극으로부터 방출된 전자의 궤적을 SIMION 프로그램을 이용하여 전산모사하였다. 전자의 출발위치와 상관없이 emitter에서 방출된 전자빔을 한곳에 집중시킬 수 있는 optimum extractor voltage Ve가 존재한다는 것을 알아내었다. Extractor voltage Ve는 source voltage Vs에 따라 변하지만, 두 전압의 비율(Ve/Vs)는 항상 일정하고, 그 값은 99.4%였다. Source와 extractor에 인가된 전압의 비율(Ve/Vs)이 99.4%일 때, 교차점에서의 빔 직경은 $1.2{\mu}m$였다. MFXG의 초점 크기는 교차점에서의 beam diameter보다 작을 수 없기 때문에, 교차점에서의 beam diameter을 작게 할 수 있는 조건을 찾는 것은 중요하다. 따라서 위의 두 결과는 MFX tube의 개발에 있어서 매우 중요한 결과로 판단된다.